Sanyo PLC-EF60A Service Manual page 90

Control Port Functions
Pin Function Name
198 RxD0
199 (Not used)
200 GND
201 RxD2
202 1.9V
203 IRQ5
204 SDA_SLOT4
205 SCL_SLOT4
206 SDA_SLOT3
207 GND
208 SCL_SLOT3
209 3.3V
210 SYS SW_CPU
211 POWER_SW_CPU
212 SDA_SLOT2
213 SCL_SLOT2
214 SDA_SLOT1
215 SCL_SLOT1
216 SDA_INNER
217 SCL_INNER
218 P_S_0
219 UCLK
220 RESETP
221 (Not used)
222 MD3
223 MD4
224 3.3V
225 3.3V
226 (USB1P)[Func]
227 (USB1M)[Func]
228 GND
229 (USB2P)[Host]
230 (USB2M)[Host]
231 3.3V
232 GND
233 LENS_V_POS
234 LENS_H_POS
235 KEY1
236 KEY2
237 3.3V
238 KEY3
239 OPT1
240 GND
Parallel I/O Expander(TE7780) (IC4801)
1 LAMP1_TX
2 GND
3 LAMP1_RX
4 PJMENU_TX
5 (Not used)
6 LAMP2_TX
7 LAMP2_RX
8 SH_BSY
9 (Not used)
10 LENS_UP_EX
11 LENS_DOWN_EX
12 GND
13 LENS_R_EX
14 LENS_L_EX
15 FPGA_CLB
16 FPGA_CONF_DATA
17 FPGA_CONF_CLK
18 FPGA_nCONFIG
19 FIL_SENS
20 SMK_SENS
21 SCDT_DVI
Function
Receive Data0 [PAD Remote Control]
SIOF Receive Data/IO Port for SCI
Power (0V)
Receive Data2 [External]
Power (1.9V)
I/O Expander(No.1) Interrupt
IIC Bus(Slot4)
IIC Bus(Slot4)
IIC Bus(Slot3)
Power for Inout/Output(0V)
IIC Bus(Slot3)
Power for Inout/Output(3.3V)
Bus Switch
Power Control
IIC Bus(Slot2)
IIC Bus(Slot2)
IIC Bus(Slot1)
IIC Bus(Slot1)
IIC Bus
IIC Bus
PW-SH Input SIgnal
USB Clock [48MHz]
Power On Reset Request
Hardware Reset Request
Bus Width Setting for Area0
Bus Width Setting for Area0
Test(3.3V Fixed)
USB Analog Power(3.3V)
USB1 Data I/O(+)
USB1 Data I/O(-)
USB Analog Power (0V)
USB2 Data I/O(+)
USB2 Data I/O(-)
USB Analog Power(3.3V)
Analog Power (0V)
Lens Position Detection(up/down)(10bit A/D)
Lens Position Detection(left/right)(10bit A/D)
KEY AD Converter Input
KEY AD Converter Input
Analog Power(3.3V)
KEY AD Converter Input
KEY AD Converter Input * Option Inut
Analog Power (0V)
For Lamp Dimmer
For Lamp Dimmer
Menu Control for PJ-Net Organizer
(Not used)
For Lamp Dimmer
For Lamp Dimmer
DPRAM Dual Access Prohibition Control (Output)
(Not used)
Lens Shift Up
Lens Shift Down
Lens Shift Right
Lens Shift Left
Circuit Initialize
Configuration Data
Configuration Clock
Configuration Start
n/a
Smoke Resist Box Detection
DVI Signal Detection
- 90 -
Pol. Action
I
- (Pull-up)
- -
I 19200bps or 9600bps
- -
I Active L
IO
IO
IO
- -
IO
- -
O
O
IO LActive
IO LActive
IO LActive
IO LActive
IO LActive
IO LActive
O L:Disable PW-DPRAM Com.H:Enable PW-DPRAM Com.
I -
I -
- (Pull-up)
I H Fixed
I H Fixed
I -
- -
I/O
I/O
- -
I/O
I/O
- -
- -
AI 0~1023:(Top:Max~Bottom:Max)
AI 0~1023:(Left:Max~Right:Max)
AI
AI
- -
AI
AI
- -
O H after Lamp on
- -
I lamp Error Detection after Lamp Control Starts
O 28800bps
I
O H after Lamp on
I lamp Error Detection after Lamp Control Starts
O L:BUSY
O
O H:ActiveL:Off
O H:ActiveL:Off
- -
O H:ActiveL:Off
O H:ActiveL:Off
O H after configuration
O
O
O
I "H":w/o Smoke L:w/ Smoke
I H:Signal Exist