Summary of Contents for Exadigm GT IPSec
-
Page 1: Setup Guide
GT IPSec Setup Guide 2 8 7 1 P u l l m a n S t r e e t , S a n t a A n a , C A 9 2 7 0 5 P h o n e . 9 4 9 . 4 8 6 . 0 3 2 0 F a x . - Page 2 The information contained in this document is subject to change without notice. ExaDigm makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties or merchantability and fitness for a particular purpose.
-
Page 3: Table Of Contents
GT IPsec Setup Guide Table of Contents Web GUI Login ..................... 4 1.1 Initial Connection ....................... 4 IPsec ........................4 2.1 Tunnel Configuration ....................5 Cisco ASA Settings ....................6 3.1 Network Diagram ....................... 6 3.2 Cisco ASA Configuration ................... 6 3.3 Cisco ASA Configuration ................... -
Page 4: Web Gui Login
The Ethernet Port on the GT is “auto-sensing”, which means a straight through or cross- Note: over cable can be used to connect to the ExaDigm router. 3. Launch a web browser and connect to the GT using the address http://192.168.12.20:8080/. If you cannot connect, verify the address provided by the GT’s DCHP host using your system’s... -
Page 5: Tunnel Configuration
GT IPsec Setup Guide Tunnel Configuration The IPsec parameters will need to be added according to the specific Adaptive Security Appliance (ASA). Click the Add button to configure the parameters. The above configuration should be set according to the ASA being used. -
Page 6: Cisco Asa Settings
GT IPsec Setup Guide Cisco ASA Settings Network Diagram Cisco ASA Configuration My Subnet will be set to the default DNS for the GT. The Peer Address is the external interface address and the Peer Subnet is the internal address. -
Page 7: Cisco Asa Configuration
GT IPsec Setup Guide Cisco ASA Configuration ASA Version 8.4(2) hostname asa2 domain-name exadigm.com enable password /xxxxxxxxxxxxxxxx encrypted passwd xxxxxxxxxxxxxxxx encrypted names interface Ethernet0/0 switchport access vlan 2 interface Ethernet0/1 interface Ethernet0/2 interface Ethernet0/3 interface Ethernet0/4 interface Ethernet0/5 interface Ethernet0/6... - Page 8 GT IPsec Setup Guide mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 nat (inside,any) source static obj-192.168.166.0 obj-192.168.166.0 destination static obj-192.168.155.0 obj-192.168.155.0 no-proxy-arp object network obj_any nat (inside,outside) dynamic interface...
- Page 9 GT IPsec Setup Guide telnet timeout 60 ssh timeout 5 console timeout 0 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept tunnel-group 166.142.29.80 type ipsec-l2l tunnel-group 166.142.29.80 ipsec-attributes ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** class-map inspection_default match default-inspection-traffic...
-
Page 10: Netgear Vpn Settings
GT IPsec Setup Guide NetGear VPN Settings Network Diagram NetGear VPN Configuration My Subnet will be set to the default DNS for the GT. The Peer Address is the external interface address and the Peer Subnet is the internal address. -
Page 11: Netgear Prosafe Vpn Screen
GT IPsec Setup Guide NetGear ProSafe VPN Screen NetGear will display the following information on their VPN setup screen. Figure 1 – page 1 of NetGear VPN setup © 2012 ExaDigm, Inc. Page 11 of 13 Rev. 1/1212... - Page 12 GT IPsec Setup Guide Figure 2 – page 2 of NetGear VPN setup © 2012 ExaDigm, Inc. Page 12 of 13 Rev. 1/1212...
-
Page 13: Ipsec Tunnel Listing
GT IPsec Setup Guide Figure 3 – page 3 of NetGear VPN setup IPsec Tunnel Listing A listing of configured Tunnels will appear. In this screen you can add new tunnels. An existing tunnel may be deleted, modified or details viewed.
Need help?
Do you have a question about the GT IPSec and is the answer not in the manual?
Questions and answers