Contents Welcome Orbitsound contact information: Package contents The soundbar Remote control The subwoofer Setting up the orbitsound T9 1. Connect subwoofer 2. Connect power 3. Connect a sound source 1. Power on 2. Source selection 3. Volume / Mute 4. Tone adjustment Advanced Setup 1.
Welcome Thank you for purchasing the orbitsound T9 compact spatial stereo soundbar with iPhone/iPod dock. With proper use the orbitsound T9 delivers superb sound fidelity, engaging stereo sound and will provide you with a fantastic listening experience. This instruction booklet covers important safety and setup information as well as advice on how to get the most out of your orbitsound T9.
BLUE (FLASHING): Mute or remote operation OFF: Power off Status LED IR receiver The orbitsound T9 soundbar produces most of the sound that you hear. It produces the main signal and stereo information. It also houses the amplifiers for itself and the subwoofer. Remote control...
Setting up the orbitsound T9 1. Connect subwoofer Connect the subwoofer to the subwoofer output on the stereo soundbar as shown: Note: The speaker wire is colour marked to make identifying the correct wire for the speaker/soundbar terminal easy. Connect the wire marked with a red tab to the red terminal on the soundbar and the subwoofer.
2. Connect power Power Cable - use correct country plug type AC Adaptor Connect the power supply as shown. 3. Connect a sound source You can connect multiple sources to the unit and listen to either: iPod connection iPod/iPhone iPod Dock Adapter AUX connection (rear of sound bar) Music source...
Basic operation 1. Power on Press & hold (2 seconds) Power on Standby IMPORTANT: The main power switch must be ‘ON’ for soundbar operation. This is located on the rear of the soundbar unit. Standby (sleep) / On: The soundbar may be put into ‘standby’ or resumed from standby by pressing the [power] button on the remote.
3. Volume / Mute Volume - Volume+ Mute Main Volume adjust Mute: Press the [mute] button on the remote to silence or resume play through the soundbar. NOTE: When the soundbar is on and mute is enabled, you will see a blue flashing light on the front of the soundbar.
Advanced Setup The orbitsound T9 is easy to set up and enjoy, but even better sound can be achieved by following these guidelines. 1. Positioning: getting the most from spatial stereo The spatial stereo sound field is produced by the speakers in the sides of the soundbar.
Connection to TV This configuration can be used for TVs with an optical digital output. The TV sends stereo sound directly to the soundbar. Connecting sound from the TV like this is usually the best sound connection method for many reasons. Connecting the soundbar directly to a set-top box / Blu Ray can introduce A/V sync issues as some TVs will delay the video a little.
There is no on screen menu, the video output is to watch video ouput only (i.e. youTube and stored videos). iPhone/iPod control & charge Basic play control is achieved by pressing the following buttons on the orbitsound T9 remote control unit: Play/Pause Stop Random Prev.
Charge / Menu The iPod/iPhone is charged when it needs charge and when connected. Also, the menus may conveniently be navigated from the remote for most iPod models. Pressing the ‘iMenu’ button enters the iPod menu. You can use the remote control’s navigation functions to control your iPhone/iPod.
Battery replacement (remote) Replace remote battery with anode up (+) from back-side. BATTERY: CR 2025 Troubleshooting No sound is heard • Check power connections and that there is a continuous blue light on the front of the unit. • Check that the iPod/TV or other sound source is playing and that it is connected properly to the soundbar.
Check the output format of the optical signal from the playing device. Choose ‘normal’ or ‘PCM’ format. Refer to the TV manufacturer’s handbook for more information. You can also contact Orbitsound for advice, see contact helpline in this handbook and on the packaging.
Orbitsound Warranty This Orbitsound product is supplied with a 12 month limited manufacturer’s warranty dated from new purchase date. This warranty covers repairs or replacement that may be required in the event of unit failure during normal use, subject to the terms and conditions stated below and at the Agent’s discression.
Page 17
that the equipment has been installed and used in accordance with the supplied handbook instructions. The warranty will not cover repairs or replacements arising from misuse or accidental damage. See Warranties and Liabilities. 3. CHARGES For warranty repairs that are 100% covered by the manufacturer’s warranty, there will be no charge for any repair or replacement or return freight to the purchaser.
GENERAL The Agent may assign or subcontract responsibilities and rights under this warranty. In all warranty cases, please refer to the support pages of www.orbitsound.com first. Contact Information ORBITSOUND LTD.
Tweeter drivers 1 x 1” m/c Front main drivers 2 x 2.5 “ Spatial drivers 2 x 2” full-range Enclosure type Sealed/orbitsound spatial Sub-Bass driver 1 x 6.5” Sub-Bass Enclosure type Low profile tuned reflex Connection input(s) Stereo Line level -10dBu 3.5mm jack and RCA.