PRODUCT SAFETY NOTICE Many electrical and mechanical parts in this chassis have special safety-related characteristics. These charac- teristics are often passed unnoticed by a visual inspection and the protection afforded by them cannot neces- sarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual and its supplements;...
SAFETY NOTICE 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the Handling the LCD Module surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT Safety Precaution cleaning agent.
Page 4
6. CMOS-LSI circuits are used in the module, so guard 9. Do not disassemble the LCD module. Disassembly can against damage from electrostatic discharge. Be sure cause malfunctions. to wear a wrist or ankle ground when handling the module. 7. Do not expose the module to direct sunlight or strong 10.
CONTENTS SECTION 1 GENERAL DESCRIPTIONS AND PART REPLACEMENT 1. LOCATION OF PARTS ............. 1-1 2-11.Switch PC Board ..............1-8 1-1. Buttons on the Front Panel, and 2-12.Hinge, Top Cover ..............1-8 Terminals on the Side and the Back Panel ......1-1 3.
SECTION 1 GENERAL DESCRIPTIONS AND PART REPLACEMENT 1. LOCATION OF PARTS 1-1. Buttons on the Front Panel, and Terminals on the Side and the Back Panel <Front> <Rear> TV/Video Volume Channel Power up/down up/down Headphone jack (2) : Video 2 input terminals (Video Audio L/R) Aerial input DC Input...
FAST BACK STOP Note: CHAPTER Toshiba VCR,DVD can be operated with these buttons. OPEN/CLOSE BACK press to pause or still. (DVD/VCR) press to open/close the tray. (DVD/VCR) Prev press to skip back the current chapter or track.
Note: 2. REMOVAL • A "snapping" sound will be heard when the claw is 2-1. Front Panel released. 1. Remove five screws (1). • Take care not to scratch the LCD. • Caution should be taken to avoid injury from edges on Screws (1) metal areas when removing the LCD panel.
3. Turn the LCD (2) on its back and remove two screws 3. Remove the connectors (4) from the four locations and (4). remove the wire from the three locations of claw B. 4. Slide the back lights (5) on the top and bottom out to Connector (4) the left side and remove the LCD (2).
2-4. Sensor PC Board 2-5. LCD Rear Cover 1. Remove one screw (1) and remove the connector (2) 1. Remove the front panel, the LCD panel and the from the one location, then remove the sensor PC inverter PC board. (Refer to item 1-1, 1-2 and 1-3.) board (3).
2-6. Wall Hanging Plate 2-8. Side Cover 1. Remove three screws (1), then remove the wall 1. Remove the left and right side covers. hanging plate (2). Side cover (right) Screws (1) Wall Hanging Plate (2) Side cover (left) Fig. 1-2-14 Fig.
3. Remove the core (5) and the cushion (6) from the 20 2-11. Switch PC Board pin connector (4). 1. Remove the cushion (1). 4. Remove the connectors (4) from the four locations, 2. Remove the connector (2). then remove the main PC board (7). 3.
3. GND LEAD WIRE CONNECTION DIAGRAM When assembling, refer to the diagram below for the GND lead wire connection. Left Right hinge hinge Left Right support support Connector Main PC board GND lead wire Switch PC board Right speaker Front net Fig.
Page 19
SECTION 3 PARTS LIST SAFETY PRECAUTION The parts identified by ! ( ) mark are critical for safety. Replace only with part number specified. The mounting position of replacement is to be identical with originals. The substitute replacement parts which do not have the same safety characteristics as specified in the parts list may create shock, fire or other hazards.
Page 22
15VL26P / 1 2. PARTS LIST Location No. Parts No. Description A201 72790313 FRONT COVER A202 72790325 TOP COVER (EU) A203 72624045 BOTTOM COVER A204 72790322 LEFT SIDE COVER(EU) A205 72624049 RIGHT SIDE COVER A206 72741033 PLATE, WALL MOUNTING A301...
SECTION 2 SERVICING DIAGRAMS 1. CIRCUIT SYMBOLS AND SUPPLEMENTARY EXPLANATION 1-1. Solid Resistor Indication 1-3. Capacitance Indication Table 2-1-1 Table 2-1-3 Symbol ..Carbon film Symbol ..Electrolytic, Special electrolytic ..Oxide metal film ..Ceramic, Film ..Ω Unit None Unit None...
2-2-1. Pin Assignments (microprocessor) IC701: KS88C6348 Name Signal In/Out Logic Remark IR-Input Active Low IR-IN Input Remote Control Signal Input MAIN-SWITCH INPUT Input Active High MASTER SW ON/OFF INPUT MAIN_SW DVD IDENT Input Active Low DVD_ID DVD JACK IDENT Input Active High SCART_ID Scart Ident...
3-12.Pin Voltage Power Circuit (Page 2-7) IC801(FDS4435) PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE IC803(LM2596) PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE 7.3V Microprocessor Circuit (Page 2-9) IC702(MC78L05) PIN VOLTAGE IC701(Microprocessor) PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE 4.4V 22 4.6V 4.7V 23 3.8V...
Page 43
Input Jack Circuit (Page 2-11) VPC3230 Circuit (Page 2-13) IC501(NJM2233) PIN VOLTAGE IC101(VPC3230) PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE PIN VOLTAGE 2.7V 41 2.3V 42 2.3V 2.7V 1.9V 43 2.3V 1.4V 44 2.3V 1.4V 45 3.3V IC502(GL3820) PIN VOLTAGE 1.4V 46 0V PIN VOLTAGE...
SPECIFICATIONS Color system PAL/SECAM/NTSC4.43 Sound system BG/DK/I/L Rated voltage ~110V-240V 50/60 Hz. Power consumption Audio power 2W + 2W Speaker type 40 x 70 mm 2pcs. External Connections EXT1: 21pin SCART input Component video (Y. P ) input + Audio (L+R) input EXT2: Video input +Audio (L+R) input, Phone jack (output) Dimensions Width 366mm, Height 362mm, Depth 170mm...