Table of Contents ............3 GENERAL INFORMATION ..Package Contents ................. 3 Safety Instructions—Please read............3 Front Panel View .................. 4 Back Panel View ..................5 .............. 6 INSTALLING THE ROUTER Connect the ADSL Line and Telephone..........6 Connect the PC to the Router ............... 6 Connect the Power Adapter ..............6 ...............7 INSTALLATION DIAGRAM...
Page 3
..............30 ACCESS MANAGEMENT ACL .....................30 Filter.....................31 IP/MAC Filter................31 Application Filter................33 URL Filter..................33 SNMP....................34 UPNP....................34 DDNS....................35 CWMP....................36 ................37 MAINTENANCE Administration ..................37 Time Zone.....................37 Firmware....................38 Sys Restart...................39 Diagnostics...................39 ..................STATUS Device Info ..................40 System Log..................40 Statistics....................41 APPENDIX TROUBLESHOOTING.............42 Using LEDs to Diagnose Problems............42 Can’t Access Web Configuration............43 Forgotten Login Username and Password...........44 Can’t Access LAN Interface..............44...
General Information The 4-Port Wireless Ethernet Router features 4 LAN ports and wireless ability. Package Contents The package includes one of each of the following items— 4-Port wireless Ethernet router Modem 12 VAC AC power adapter RJ-11 telephone cable ...
Front Panel View Mode Indication Wireless is disabled. WLAN Wireless is enabled or wireless traffic. Blinking ADSL link established and active. Blinking ADSL is not connected. Link Quick ADSL is trying to establish link。 blinking ADSL is not connected. blinking ADSL traffic.
Back Panel View Port Description On / Off Press to turn the router on and off. Power Connects to a 12 VAC AC power adapter. RJ-45 connects the unit to an Ethernet device such as a LAN1-LAN4 PC or a switch. Restart—press the button for less than 4 seconds.
Installing the Router Connect the ADSL Line and Telephone An RJ-11 cable will be connected to the wall phone jack and the Line - end of the splitter. Connect another RJ-11 phone wire from the modem-end of the splitter to the port labeled “line” on the router.
Mounting the Router The router can be mounted on the wall with the screws provided. Mounting can be done on wall material including concrete, wood, or drywall. Select an appropriate location free from obstructions or any possible interference. Make sure the cables can be easily attached to the router without strain.
Configuring Your Computer Prior to accessing the router through the LAN port, note the following necessary configurations— Your PC’ s TCP/IP address: 192.168.1. (The last number is any number between 2 and 254) The router’s default IP address: 192.168.1.1 ...
8. After your computer restarts, click on the Network and Dial- up Connections icon again, and right click on the Local Area Connection icon and then select Properties. 9. In the Local Area Connection Properties dialog box, select Internet Protocol (TCP/IP) and then click on Properties. 10.
Logging into the Router This section explains how to login to your router using the following steps— 1. Launch your web browser. 2. Enter the URL in the address bar and click on http://192.168.1.1 Enter. A login screen like the one below will be displayed after you connect to the user interface.
Interface Setup This section of the user manual is on the Interface configurations of the router. The under Interface Setup are Internet, LAN and Wireless. Internet The Internet Configuration screen allows you to configure the ATM VC and Encapsulation. 1、ATM VC & QoS The ATM PVC Configuration screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a ATM QoS service category.
Verify the following values with your ISP before you change them. LABEL DESCRIPTION Virtual Circuit Select the PVC you wish to modify. Status Each PVC can be toggled Activated or Deactivate. Enter the VPI here. VPI can range from 0 to 255. Enter the VCI here.
Page 15
The following table describes the labels in this screen. LABEL DESCRIPTION Encapsulation Select your encapsulation type from the dropdown list. Select whether NAT is Enabled or Disabled. Default Route Select whether this PVC will be the default route for Internet data. Dynamic Route Select the RIP type and direction from the dropdown lists.
Page 16
◆ PPPoE/PPPoA The following table describes the labels in this screen. LABEL DESCRIPTION Username Enter your username here. Password Enter your password here. Encapsulation Select your encapsulation type from the dropdown list. Connection Select whether your connection is always on or if it connects demand.
the user name exactly as your ISP assigned it. If the assigned name is in the form of user@domain where domain identifies a service name, enter it exactly as given. Bridge Mode ◆ The following table describes the labels in this screen. LABEL DESCRIPTION Encapsulation...
The following table describes the labels in this screen. LABEL DESCRIPTION IP Address Enter the IP address you wish to use with your LAN here. IP Subnet Mask Enter the IP subnet mask you wish to use with your LAN here. Dynamic Route Select the Routing Information Protocol (RIP) you wish to use from the dropdown list and the direction you want from the dropdown list.
Page 19
The following table describes the labels in this screen. LABEL DESCRIPTION Starting IP Address Enter the starting IP address you wish to use as the DHCP server's IP assignment. IP Pool Count Enter the maximum user pool size you wish to allow. Lease Time Enter the amount of time you wish to lease out a given IP address.
Wireless This section introduces the wireless LAN and some basic configurations. Wireless LANs can be as simple as two computers with wireless LAN cards communicating in a peer-to-peer network or as complex as a number of computers with wireless LAN cards communicating through access points which bridge network traffic to the wired LAN.
larger than the maximum MSDU (MAC service data unit) size turns off the RTS/CTS handshake. Setting this attribute to zero turns on the RTS/CTS handshake Enter a value between 1500 and 2347. Fragmentation Threshold: The threshold (number of bytes) for the fragmentation boundary for directed messages.
Key 1 to Key 4: Enter the key to encrypt wireless data. To allow encrypted data transmission, the WEP Encryption Key values on all wireless stations must be the same as the router. There are four keys for your selection. The input format is in HEX style, 5 and 13 HEX codes are required for 64-bitWEP and 128-bitWEP respectively.
Page 23
To change your router’s MAC filter settings, click Wireless LAN, MAC Filter to open the MAC Filter screen. The screen appears as shown. Active: Select Activated to enable MAC address filtering. Action: Define the filter action for the list of MAC addresses in the MAC address filter table.
Advanced Setup This section of the user manual is on the advanced configurations of the router. The topics under Advanced Setup are Firewall, Routing, NAT, QOS, VLAN and ADSL . Firewall Select whether the Firewall and SPI will be enabled, and click on SAVE. Routing This screen shows the routing rules you have already set.
The following table describes the labels in this screen. LABEL DESCRIPTION Destination IP Address Enter the destination IP address for this routing rule. IP Subnet Mask Enter the destination IP subnet mask for this routing rule. Gateway IP Address Enter the gateway IP address for this routing rule or select which PVC will be affected by this routing rule.
Page 26
◆ A demilitarized zone (DMZ) is a host between a private local network and the outside public network. It prevents outside users from gaining access to a server that you wish to keep private. Users of the public network outside the company can only access the DMZ host. The following table describes the labels in this screen.
The following table describes the labels in this screen. LABEL DESCRIPTION Rule Index Select which rule index to use with this virtual circuit. All VCs with the same IP will use the same rules. Application Select the Application you wish to use from the dropdown list .
On this screen you can ADD and delete QoS settings. VLAN A Virtual LAN (VLAN) is a switched network logically segmented by functions, project teams, or applications; the physical location of VLAN members is unimportant. VLANs allow ports on the same or different switches to be grouped so that traffic is confined to members of only that group.
Click on Assign VLAN PVID for each Interface or Define VLAN group to open there spec. screens. 1、Assign VLAN PVID for each Interface Enter the PVID number you wish to assign to ATM VC, Ethernet Port and Wireless LAN. When you are done making changes, click on SAVE to save your changes, CANCEL to exit without saving or NEXT to continue to the next screen.
The following table describes the labels in this screen. LABEL DESCRIPTION VLAN Index The number of the index is determined by the model or IC. Active Toggle this index on or off with Yes and No, respectively. VLAN ID Enter the VLAN ID number. ATM VCs Checking the Tagged and Port # boxes for each port number will add a tag to let other devices know if they need to check the packet and allow...
The following table describes the labels in this screen. LABEL DESCRIPTION ADSL Mode Select which mode your ADSL connection uses from the dropdown list. ADSL Type Select the ADSL type you use from the dropdown list. When you are done making changes, click on SAVE to save your changes. Access Management The access management screens help you manage what can access your network.
The following table describes the labels in this screen. LABEL DESCRIPTION ACL can be toggled Activated or Deactivated. ACL must be Activated before you can edit the settings. ACL Rule Index Select the rule index you wish to edit. Active Toggle the rule on or off with Yes or No, respectively.
Page 33
The following table describes the labels in this screen. LABEL DESCRIPTION Filter Type Selection Select the filter type you wish to apply. IP Filter Set Index Select the IP Filter Set Index you wish to modify. Interface Select the Interface you wish to modify. PVC0-PVC7 are WAN interfaces Direction Select which direction of data flow you wish to apply the filters to.
Port Number Enter the port number of the source IP address. Note that 0 means all that ports are allowed. Destination IP Address Enter the destination IP address that you wish to deny access to your system. Subnet Mask Enter the subnet mask of the destination IP address. Port Number Enter the port number of the destination IP address.
changes or CANCEL to exit without saving. 3、Filter Type : URL Filter When you are done making changes, click on SAVE to save your changes, DELETE to delete the rule with the parameters you set or CANCEL to exit without saving. SNMP Simple Network Management Protocol (SNMP) is a protocol for exchanging management information between network devices, and is...
UPnP Universal Plug and Play (UPnP) is an open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. An UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network.
DDNS can be toggled Activated and Deactivated. DDNS must be activated before you can edit the following options. The following table describes the labels in this screen. LABEL DESCRIPTION Active Dynamic DNS can be toggled Activated or Deactivated. Service Provider Select the name of your Dynamic DNS service provider.
When you are done making changes, click on SAVE to save your changes, CANCEL to exit without saving. Maintenance The maintenance screens help you manage your router. Administration Use the Administration screen to change your password. Page 37 Total 47 pages...
The following table describes the labels in this screen. LABEL DESCRIPTION New Password Enter the password you wish to use here. Confirm Password Enter the password again to confirm it. Time Zone Use the Time Zone screen to change your router’s time and date. following table describes the labels in this screen.
Firmware Use the Firmware screen to view and update your router’s firmware. The following table describes the labels in this screen. LABEL DESCRIPTION Current Firmware Ver The current firmware version your device is using. New Firmware Location The location on your computer of the firmware you wish to upload. Enter the location here, or click on Browse…...
Diagnostics The Diagnostics screen tests the performance of your virtual circuits. Select which PVC you wish to test from the dropdown list. The router will automatically run diagnostic tests on that circuit. A green PASS means that the given test was passed, a red FAIL means that the test was failed and a green SKIPPED means that the test was skipped.
System Log The system log screen displays a log of the router’s functioning. Click on CLEAR LOG to clear the log or on SAVE LOG, which will save the log data to a separate file. Statistics The statistics screen gives you information on how much data your router has processed.
Appendix Troubleshooting This chapter covers potential problems and the corresponding remedies. Using LEDs to Diagnose Problems The Light-Emitting Diodes (LED) are useful aides for finding the possible causes of problems. Problem: Power LED Doesn’t Light Up The Power (PWR) LED on the front panel does not light up. STEPS CORRECTIVE ACTION Make sure that the router’s power adaptor is connected to the router and...
Problem: DSL LED Doesn’t Light Up The DSL LED on the front panel does not light up. CORRECTIVE ACTION STEPS Check the telephone wire and connections between the router DSL port and the wall jack. Make sure that the telephone company has checked your phone line and set it up for DSL service.
The Web configurator does not display properly. STEPS CORRECTIVE ACTION Make sure you are using Internet Explorer 5.0 or later versions. Delete the temporary Web files and log in again. In Internet Explorer, click Tools, Internet Options and then click the Delete Files ... button.
Can’t Access WAN Interface Initialization of the ADSL connection failed. STEPS CORRECTIVE ACTION Check the cable connections between the ADSL port and the wall jack. The DSL LED on the front panel of the router should be on. Check that your VPI, VCI, type of encapsulation and type of multiplexing settings are the same as that you obtained from your telephone company and ISP.
Can’t Access Remote Management I cannot remotely manage the ROUTER from the LAN or WAN. STEPS CORRECTIVE ACTION Refer to the Remote Management Limitations section in the Firmware and Configuration File Management chapter for scenarios when remote management may not be possible. Use the router’s WAN IP address when configuring from the WAN.