Download
Share
Print this page
  1. Manuals
  2. Brands
  3. GSD Manuals
  4. Controller
  5. GSDn-WEC
  6. Installation & user manual

GSD GSDn-WEC Installation & User Manual

Wi-enterprise controller
Hide thumbs

Advertisement

Quick Links

Download this manual
Other products from GSD
GSD Wi-Max System
in access control solutions. It provides a
Wireless Network throughout the premises,
giving the convenience and security of a fully
networked system for a fraction of the cost.
For more information on the Wireless Network System visit our website
www.globalsecurity.ie
No.1 Turnpike Business Park,
Ballymount,
Dublin 22, Ireland.
Telephone: +353 1 524 2691.
Fax: +353 1 4430 430.
"Wireless Network
System"
is the next generation
Contents
3
Installation Instructions
4
6
8
9
12
19
Wi-Enterprise Controller
Installation & User Manual
V2.04

Advertisement

loading
Need help?

Need help?

Do you have a question about the GSDn-WEC and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for GSD GSDn-WEC

  • Page 1: Table Of Contents

    Other products from GSD “Wireless Network System” GSD Wi-Max System is the next generation in access control solutions. It provides a Contents Wireless Network throughout the premises, giving the convenience and security of a fully networked system for a fraction of the cost.
  • Page 2 Dimensions - Flush Mount W. 87mm D. 21mm H. 119mm - Surface Mount W. 87mm D. 35mm H. 119mm Phase 1- Setting up the GSD Controller Phase 2 - Configuring the GSD Controller Features Phase 3 - Enrolling Door Controls...

  • Page 3: Installation Diagrams

    Installation Diagrams Installation Diagrams Control Panel opening Control Panel features cable entry mount with 4 x 1.5 inch access to rear No. 8 Security Type screws mount hole void for wiring spirit level remove screw cap remove retaining screw mains pcb cable entry cable...

  • Page 4: System Overview

    System Overview System Overview RS485 Connection to Door Controls Wireless Connection to Door Controls TCP-IP connection to Controllers TCP-IP connection to Controllers Note: If using a single Controller, Note: If using a single Controller, RS485 Network to Controllers an RS232 cable may be used. RS485 Network to Controllers an RS232 cable may be used.

  • Page 5: Wiring Diagrams

    10 for wiring Door Network PC Direct PC Network PC Direct Connection can be used, when Main Input Cable using ONLY one GSD Controller. 230VAC Set the Direct address to ALL dip switches OFF (see below ) Pull Remove Battery Tab...
  • Page 6 All dip-switches ON. The dip-switches’s should then be set to the controller Address 1 - Set SW1 ON Address 2 - Set SW2 ON Address 3 - Set SW3 ON address as shown above in section “Setting the GSD controller address”...

  • Page 7: Operation Instructions

    Operation Instructions Operation Instructions Setting up TCP-IP - Static IP Setting up TCP-IP - DHCP Step Description Step Description Default the Controller. See Restore Factory settings on page 11. The Default the Controller. See Restore Factory settings on page 11. The Controllers default IP address is 169.254.1.1.
  • Page 8 Controller a clean set of instructions before beginning to enroll (see instructions on page 11) doors onto the network. This will take approximately 1 minute. Follow instructions on the CD provided to install the GSD PC application. WARNING! A New Network should only be created on first installation.
  • Page 9 Operation Instructions Operation Instructions Phase 3 - Enrolling Door Controls Phase 3 - Enrolling Door Controls Step Description Step Description The controller is now ready to allow Door Controls to enroll onto the All Door Controls should be installed at this point and powered up. Network –...
  • Page 10 Operation Instructions Operation Instructions Phase 4 - Configuring Users Phase 3 - Enrolling Door Controls Step Description Step Description Once all Door Controls are enrolled onto the network – go back to the Enable a User by ticking the ‘Enabled’ box for each User Controller application and click the ‘Secure Network’...

  • Page 11: Fingerprint Enrollment

    Operation Instructions Operation Instructions Enrolling User FingerPrints Phase 5 - Configuring Access Levels Step Description Step Description Access Levels are controlled by creating UserGroups and assigning the Note: Make sure the USB Fingerprint reader is attached to the PC UserGroup to a User as described in section ‘Configuring Users’. Select the User for fingerprint enrollment UserGroups are created by combining pairs of DoorGroups with Timezones.
  • Page 12 Finger Placement Wi-BIO Finger Placement Wi-BIO Correct Finger Placement Incorrect Finger Placement Note: Incorrect placement : finger does not fully cover the sensor window. Good Quality Image Poor Quality Image Note: Ensure that the core of finger is centered on the sensor window during the enrollment process.
  • Page 13 Finger Placement Wi-BIO Finger Placement Wi-BIO Correct Finger Placement Incorrect Finger Placement...
  • Page 14 Installation Records Installation Record Ctrl Door No. Door Type Door Location Name Walk Test Ctrl Door No. Door Type Door Location Name Walk Test...