Summary of Contents for MKN 2023104-00ABBE-B
- Page 1 Operating Manual Induction hob Open out the cover page to see the controls and displays. Version Size Induction hob 1-zone hob 2-zone hob 4-zone hob 2023104-00ABBE-B / en-GB Operating Manual...
- Page 2 Induction hob Induction hob Controls and displays Figure 1: Controls and displays, 4-zone induction hob Unit switch Control lamp front right Operation and malfunction” Power control front right Control lamp rear right Operation and malfunction” Power control rear right Control lamp front left Operation and malfunction” Power control front left Control lamp rear left Operation and malfunction”...
-
Page 3: Table Of Contents
Induction hob Contents Introduction ............Intended use ..............About this operating manual ........... Warnings ................Warranty and liability ............Signs and symbols ............Safety information ..........Construction and function ........Description of the unit ............3.1.1 Tabletop unit ................3.1.2 Floor standing unit .............. - Page 4 Contents Induction hob Faults ..............Explanation of the coded flashing ........Causes of faults and troubleshooting ......Service ..............Disposal ................7.1.1 Disposing of the air filter ............. Declaration of Conformity ........Operating Manual...
-
Page 5: Introduction
Introduction 1 Introduction 1.1 Intended use MKN units are solely intended to be used for commercial purposes, especially in commercial kitchens. The unit may only be used for cooking food with suitable cookware. It is not permitted to use the unit for the following purposes, among others:... -
Page 6: Warnings
Incorrect commissioning, operation or servicing of the unit Technical changes to the unit without the binding agreement of the manufacturer Use of spare parts or accessories not approved by MKN Faults resulting from the failure to comply with these operating instructions... -
Page 7: Signs And Symbols
Induction hob Introduction 1.5 Signs and symbols DANGER (Type and source of danger) Imminent danger Non-observance leads to death or serious injury. WARNING (Type and source of danger) Possible danger Non-observance can lead to death or serious injury. CAUTION (Type and source of danger) Dangerous situation Non-observance can lead to slight and semi-serious injury. -
Page 8: Safety Information
Safety information Induction hob 2 Safety information MKN appliances comply with the relevant safety standards. However, this does not mean that all possible dangers that may arise, e.g. due to incorrect operation, can be excluded. Therefore, when operating the unit, the operating staff must be familiar with and observe local regulations, e.g. - Page 9 Induction hob Safety information Risk of injury due to ceramic glass splinters ® Damaged Ceran ® Do not allow any hard or pointed objects to fall onto the Ceran hob. ® Do not operate the unit if the Ceran hob is damaged. Switch off the damaged unit immediately and disconnect it from the mains.
- Page 10 Safety information Induction hob Improper use Equipment damage due to improper use ® Do not place any wet pots on the Ceran Remove any scattered salt or boiled-over food immediately. Do not use pots and pans with rough surface. Avoid overheating and turn down the power control in good time. Do not operate the unit without the air filter insert.
-
Page 11: Construction And Function
Induction hob Construction and function 3 Construction and function 3.1 Description of the unit 3.1.1 Tabletop unit Figure 2: Counter SL 2-zone induction Type plate ® Ceran Unit switch Cooking zone marking Operation and malfunction” Air filter (tray insert) control lamp Power control Operating Manual... -
Page 12: Floor Standing Unit
Construction and function Induction hob 3.1.2 Floor standing unit Figure 3: Optima 4-zone induction range Type plate ® Ceran Unit switch Cooking zone marking Operation and malfunction” Air filter (tray insert) control lamp Power control Operating Manual... -
Page 13: Features
Induction hob Construction and function 3.2 Features Main components Housing made of chrome nickel steel ® Ceran Air filter Electrical features Unit switch Operation and malfunction” control lamp Power control Induction generator with pot detection Power supply cable with unit switch (tabletop unit) Fixed electrical connection (floor standing unit) 3.3 Functions of the controls and displays Control/display... -
Page 14: Operation
Operation Induction hob 4 Operation Open out the cover page to see the controls and displays. 4.1 Initial use Before using for the first time: 1. Remove any production or packaging residues. 2. Clean the unit (see Chapter Cleaning”, Page 17). -
Page 15: Switching On/Switching Off The Unit
Induction hob Operation 4.4 Switching on/switching off the unit 4.4.1 Switching on Turn the u nit swit c h (1). Unit is switched on. 4.4.2 Switching off Turn the u nit swit c h (1 ) to the zero position. Unit is switched off. -
Page 16: End Of Operation And Breaks
Operation Induction hob 4.7 End of operation and breaks 4.7.1 Short breaks 1. Remove cookware from the cooking zone. The induction function is switched off and is in stand-by mode. All control lamps light up for four seconds. 2. To continue cooking, place the cookware back on the cooking zone. Induction is active. -
Page 17: Cleaning
Induction hob Cleaning 5 Cleaning 5.1 Avoiding corrosion Keep the surfaces of the unit clean and well aired. Regularly remove accumulated layers of scale, grease, starch and protein. Regularly remove salt deposits. Only allow parts made of stainless steel to come into brief contact with strongly acidic foodstuffs, spices, salts or similar substances. -
Page 18: Cleaning The Ceran® Hob
Cleaning Induction hob CAUTION Damage due to abrupt cooling Never cool the unit abruptly. Clean the unit after use. Switch off the unit and allow to cool before cleaning. Clean the housing with warm water and standard detergent. 5.3 Cleaning the Ceran ®... -
Page 19: Exchanging The Air Filter
Induction hob Cleaning 5.4 Exchanging the air filter 5.4.1 Replacing the air filter underneath the unit Do not operate the unit without the air filter. Only use original filter mats (order no. 216036) or a pre-cut mat of filter class EU4. 1. -
Page 20: Exchanging The Air Filter In The Tray Insert
Cleaning Induction hob 5.4.2 Exchanging the air filter in the tray insert Check the air filter regularly for soiling and replace if necessary. 1. Switch off the unit. 2. Pull out the filter insert. 3. Take out the old filter mat and insert a new one. 4. -
Page 21: Faults
Induction hob Faults 6 Faults 6.1 Explanation of the coded flashing The control lamp indicates the operating state of the unit. Malfunctions during operation are signalled by a periodical flashing which is coded. code pause code pause msec msec msec 6.2 Causes of faults and troubleshooting Open out the cover page to see the controls and displays. - Page 22 Faults Induction hob Operating status Optical signal Fault Possible causes Remedy Unit is switched Control lamp flashes Cookware is not Power control is set to Set power control to 1-8”. briefly every four heated the zero position seconds Unsuitable cookware Use suitable cookware (see Power control is (too small or unsuit-...
- Page 23 Induction hob Faults Operating status Optical signal Fault Possible causes Remedy Internal error _ _ _ • Heat output was Inductor overheated Remove cookware. status with coded turned off dur- Turn the power control to the Empty cookware being flashing signal ing heating zero position (do not turn heated...
- Page 24 Faults Induction hob Operating status Optical signal Fault Possible causes Remedy Internal error • • • • No heat output Quality of the mains If all cooking zones are affected: status with coded or heating power is not adequate Check power supply, fuses flashing signal switches on and or power level fault...
-
Page 25: Service
Induction hob Service 7 Service When contacting the service department, always provide the serial number and device type (see type plate). MKN GmbH & Co D-38300 Wolfenbüttel SN: XXXXXXX Typ: XXXXXXXXXX XX,X kW IP XX Figure 4: Type plate Serial number... -
Page 26: Declaration Of Conformity
Declaration of Conformity Induction hob 8 Declaration of Conformity Operating Manual... - Page 27 Induction hob...
- Page 28 Induction hob MKN Maschinenfabrik Kurt Neubauer GmbH & Co. Halberstaedter Straße 2 D-38300 Wolfenbuettel (Germany) Phone +49 (0) 53 31 / 89-0 Fax +49 (0) 53 31 / 89-280...
Need help?
Do you have a question about the 2023104-00ABBE-B and is the answer not in the manual?
Questions and answers