Philips 190EW9FB 00 Service Manual page 38

38 190EW9 LCD
General Trouble Shooting Guide
Philips's monitors build in VESA DDC2B feature to support Plug & Play requirement for Windows 95/98/2000/Me. You can install the
information file(.inf) in order to select your Philips monitor from "Monitor" dialog box in Windows 95/98/2000/Me to activate Plug &Play
application. The installation procedure based on Windows 95 OEM Release 2, 98, Me and 2000 is specified as follows, (in case of
connecting the monitor to the PC compliant with VESA standard with the designated signal cable, the PC reads display pixels ,frequency
and color feature of this monitor to optimize the picture for the monitor automatically.)DDC: Abbreviation for Display Data Channel
For Windows 95
For Windows 95 drivers,
your monitor is listed under
manufacture name "Philips
Business Electronics Co.".
1. Start Windows 95
2. Click the 'Start' button, point
to 'setting', and then click
'control panel'.
3. Double click the' display'
lcon.
4. Choose the 'setting' tab then
click 'advanced...'
5. Choose 'monitor' button,
point to 'change...' then click'
have disk...'.
6. Click 'browse...' button then
choose the appropriate drive
F:(CD-ROM Drive) then click
'ok' button.
7. Click the 'ok' button then
choose your monitor mode
land click the 'ok'.
8. Click 'close' button.
FOR WINDOWS 95/98/2000/ME OR LATER
For Windows 98
For Windows 98 drivers, our monitors are listed
under 2 manufactures name "Philips", and "Philips
Consumer Electronics Co." Please select
"Philips"when you would like to set up your monitor
in Windows setting, if you can not find the right
model name just as the label indication on the back
of set.
For those set that have been issued since the
release of Window 98, drivers can be found in
CD-ROM under the directory path of "\pc\driver\" or
it may be downloaded at http://www.philips.com.
Once you
have installed the new driver, Windows will add a
new manufacture name "Philips Business
Electronics" in your system.
1. Start Windows 98
2. Click the 'Start' button, point
to 'setting', and then click'
control panel'.
3. Double click the 'display' lcon.
4. Choose the 'setting' tab then
click 'advanced...'
5. Choose 'monitor' button, point
to 'change...' then click 'next'.
6. Choose 'display a list of all the
drivers in a specify location, so
you can select the driver you
want', then click 'next' and then
click 'have disk...'
7. Click 'browse...' button then
choose the appropriate drive
F: (RD-ROM Drive) then click
｀ok＂ button.
8. Click the 'ok' button then
choose your monitor model and
click the 'next' button.
9. Click 'finish' button then click
'close' button.
For Window Me
1. Start Window Me
2. Click the 'start' button,
point to 'setting' , and then
click 'control panel'.
3. Double click the 'display'
lcon.
4. Choose the 'setting' tab
then click 'advanced...'.
5. Choose 'monitor' button,
then click 'change...' button.
6. Choose 'specify the
location of the driver
(advanced)' and click the
'next' button.
7. Choose 'display a list of all
the drivers in a specific
location, so you can select
the driver you want', then
click 'next' and then click
'have disk.'.
8. Click 'browse...' button
then choose the appropriate
drive
F: (CD-ROM Drive)
then click 'ok' button.
9. Click the 'ok' button then
choose your monitor model
and click the 'next' button.
10. Click 'finish' button then
click 'close' button.
For Windows 2000
1. Start Windows 2000
2. Click the 'start' button, point to 'setting', and
then click 'control panel'.
3. Double click the 'display' lcon.
4. Choose the 'setting' tab then click
'advanced...'.
5. Choose 'monitor;
- If the 'properties' button is inactive, it means
your monitor is properly configured.
Please stop installation.
- If the 'properties' button is active, click
'properties' button.
6. Click 'driver' and then click on 'update
driver...' then click on the 'next' button.
7. Choose 'display a list of the known drivers
for this device. so that I can choose a specific
driver' then click 'next' and then click 'have
disk...'.
8. Click 'browse...' button then choose the
appropriate drive F: (CD-ROM Drive).
9. Click the 'open' button then click the 'ok'
button.
10. Choose your monitor model and click the
'next' button.
11. Click 'finish' button and then click the
'close' button. If you can see the 'digital
signature not found' window then click the 'yes'
button.