Pioneer AVIC-F700BT Service Manual page 58

1
QQ
- Flow Chart
3 7 63 1515 0
[Key]
Contents
Test Mode In
A
Display
Source On
TRK
[07]
(T.Offset is adjusted)
TRK
00 00 00
[07] [03]
Power Off Focus Close
B
S curve check
TRK MIN SEC TRK
91 91 91
[07] [01]
T.Close & AGC
Power Off
Applicable servomechanism
TRK MIN SEC TRK
?tr ?min ?sec
[07] [01]
Power Off F,T,RF AGC
F.Bias display switching
TRK MIN SEC TRK
??
C
[07]
Power Off
TRK MIN SEC
TE
L 13942296513
→
*1) TYP
TRK MIN SEC
*2) Focus Close → S Curve check setting → F EQ measurement setting
TRK MIN SEC TRK
00 00 00 01
TRK MIN SEC
( 99 99 99)
D
*3) F.Offset Display → RF.Offset → T.Offset Display → Switch to the
*4) 1TR/4TR/10TR/32TR/100TR
→ 4TR → 10TR → 32TR → 100TR → CRG Move
*5) Single
9x(8x):91(81) 92(82)
*6) Only at the time of CRG move, 100TR jump
*7) TRK/MIN/SEC → F.AGC → T.AGC Gain → F.Bias → RF AGC
E
*8) CRG motor voltage = 2 [V]
→
*9) TYP (1X)
TRK MIN SEC TRK
www
• As for the double speed (2x), audio output cannot be supported
*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
F
• In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
58
1
http://www.xiaoyu163.com
2
MIN SEC
[03] [02]
Power On Power On
(T.Offset is not adjusted) Gain switching
MIN SEC TRK MIN SEC TRK
99 99 99 GG
[06] [01]
Focus Mode switching Tracking Servo
*2
00 00 00
MIN SEC TRK MIN SEC
0X 0X 0X or 99 99 99
[06] [03]
T.Close RF AGC /
Applicable servomechanism RF AGC coefficient display
MIN SEC TRK MIN SEC TRK
?tr ?min ?sec ??
[03] [06]
*7
F,T AGC / F.Bias CRG/TR jump
RF AGC value switching
MIN SEC TRK MIN SEC TRK
?? ?? ?tr ?min ?sec ?tr ?min ?sec
→
+ 6 dB + 12 dB
TRK MIN SEC TRK MIN SEC
06 06 06 12 12
MIN SEC TRK MIN
01 01 02 02
order of the original display
93(83) 94(84) 95(85)
→
2X 1X
MIN SEC TRK MIN SEC
22 22 22 11 11
x ao
y
. i
AVIC-F700BT/XS/UC
2
http://www.xiaoyu163.com
3
[04]
*1 *9
RF AMP SPINDLE
Speed switching
MIN SEC TRK MIN SEC
GG GG SP SP SP
[08] [09]
CRG +
Close *8
00 00 00 00 00 00
or 99 99 99 or 99 99 99
[08] [09]
CRG +
MIN SEC 8X 8X 8X 8X 8X 8X
?? ?? or 9X 9X 9X or 9X 9X 9X
*5
[08] [09]
CRG/TR Jump + CRG/TR Jump -
*4
MIN SEC TRK MIN SEC TRK
?tr ?min ?sec ?tr ?min ?sec
[02]
Tracking Open
8X 8X 8X
Q Q
or 9X 9X 9X
3 6 7
[Key]
12
[07] Power On/Off
CRG + / TR Jump +
[08]
(Direction of the external surface)
SEC
02
CRG - / TR Jump -
[09]
(Direction of the internal surface)
[01] T. CLS & AGC & Applicable servomechanism /
AGC,AGC display setting
[02] RF Gain switching / Offset adjustment display /
T.Balance adjustment / T. Open
[03] F. Close,S Curve / Rough Servo and RF AGC /
F,T,RF AGC
SPDL 1X/2X switching
[04]
As for the double speed(2x), audio output cannot be
96(86)
supported.
Error Rate measurement
[5]
[6] F. Mode switching / Tracking Close / CRG•TR
Jump Switching
*10) OFF(TYP)
TRK MIN SEC
11
u163
3
4
2 9 9 4
8
[02]
[05]
CRG - Self-adjusting
Gop Mode
*8 switching *3
Gop Mode switching
TRK MIN SEC
TRK
?? ?? ??
OL
[02]
CRG - T.Balance adjustment /
T.BAL coefficient display
TRK MIN SEC
?? ?? ??
[02]
Tracking Open
*4
8X 8X 8X
MIN SEC
or 9X 9X 9X
*6
1 3 1 5 0 5 8 2 9
Operation
Test Mode
ON : ERR 30Counts Start
BER display data[%]
→ →
FORCUS TRACKING
TRK MIN SEC TRK MIN
70 70 70 71 71
m
co
.
4
2 8
9 9
*10
MIN SEC
OL OL
9 4 2 8 9 9
SEC
71