Advertisement
10 ft x 20 ft / 3 m x 6 m
STEEL FRAME CANOPY
Instruction Manual
ITM./ART.496840
Before assembly, read these instructions carefully.
Assemble the canopy in the location where you intend to use it.
2 or more people are recommended for assembly.
WARNING
: Keep all flame and heat sources away from this canopy fabric.
This canopy is made with fabric that meets CPAI-84 specifications for flame resistance.
It is not fire proof. The fabric will burn if left in continuous contact with a flame source.
This canopy is meant for vehicle/boat storage and should not be used for public
gatherings.
Please check with your local regulations prior to purchasing this item. Some
municipalities have restrictions and requirements.
This canopy should not be used during heavy wind, ice or snowing conditions. The
accumulation of snow and ice on canopy roof may pose a safety concern. Under severe
weather conditions, disassemble your canopy and store indoors.
It is strongly recommended that the canopy remain secure to the ground at all times via
the base plates and nylon straps supplied. Avoid placing the unit on soft ground and
ground that is prone to flooding.
MADE IN CHINA
For parts or customer service, please call 1-800-867-9018
Monday-Friday, 8:30am-4:30pm Pacific Standard Time
1
Advertisement
Table of Contents
Summary of Contents for Zhengte 496840
- Page 1 10 ft x 20 ft / 3 m x 6 m STEEL FRAME CANOPY Instruction Manual ITM./ART.496840 Before assembly, read these instructions carefully. Assemble the canopy in the location where you intend to use it. 2 or more people are recommended for assembly.
-
Page 2: Parts List
PARTS LIST PART ID DESCRIPTION ILLUSTRATION QUANTITY Incline Bar - 62” length Horizontal Bar - 75 5/8” length Post - 76” length Post - 76” length 3-way corner 4-way corner Awning Arm Awning Front Girder Bolt (M6x16mm) Bolt (M6x30mm) Ring pin w/hair spring cotter Base plate Bolt &... - Page 3 ROOF FRAME ASSEMBLY Each bar (A, B) has a spring activated button for locking into the corner pieces. Insert bars into corner pieces (D, E) as shown in the diagram below. A- Incline Bar B- Horizontal Bar D- 3-Way Corner E- 4-Way Corner POST ASSEMBLY –...
- Page 4 CANOPY ROOF ASSEMBLY Spread canopy roof (M) over assembled roof frame. If you want to attach the end panels (P & Q) then you should do so at this point. See “SIDE AND END PANEL ASSEMBLY” on page 5. POST ASSEMBLY – Part 2 Insert the remaining posts (C) into the corners on the other side of the roof as shown in the diagram.
- Page 5 BASE PLATE ASSEMBLY Insert base plates (K) onto the bottom of the posts (C, C1) and secure using the nuts and bolts (L). SIDE AND END PANEL ASSEMBLY Attach the side panel with awning (N) to the steel frame using the elastic ball straps (R). Attention: side panel with awning (N) must be attached to the side with posts (C1).
- Page 6 FINAL ASSEMBLY 1. Remove hooks from the corner posts. 2. Secure adjacent panels with hook and loop fasteners on edge of each panel. 3. Secure panels to the posts with the 3 hook 4. Insert the hooks into the pre-drilled holes at and loop fasteners attached to the side panels.
- Page 7 INSTRUCTIONS FOR ANCHORING CANOPY TO THE GROUND Listed below are 2 options for attaching this canopy to the ground Option 2: Canopy must be installed on a firm level surface, Option 1: Assemble on grass or dirt. Secure the regardless of surface type. To ensure safe use of this canopy, install canopy to the ground by inserting 8 ground stakes (S) foot plates permanently into poured concrete blocks or railroad ties through each base plate (K).
- Page 8 AWNING ASSEMBLY Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8...