Download Print this page

Advertisement

Quick Links

Marvel
TO AVOID CONFUSION DURING INSTALLATION
follow steps 1 through 5 listed below
Step 1. Remove pages 2 through 6 from book
Step 2. Remove your router install pages
Step 3. Return extra pages to box
Step 4. For smoothest plunging action purchase
STP® before installation. SEE PAGE 3
Step 5. See page 2 for parts diagram
Router Install Pages
MLCS Marvel 60
MLCS Marvel 62
60 & 62
instructions
7-8-9
10-11-12
©
2000-2006 Router Technologies
All Rights Reserved
Router
For Parts or Installation Assistance Contact
MLCS Woodworking
1-800-533-9298
mlcswoodworking.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the Marvel 60 and is the answer not in the manual?

Questions and answers

Summary of Contents for MLCS Marvel 60

  • Page 1 Step 3. Return extra pages to box Step 4. For smoothest plunging action purchase STP® before installation. SEE PAGE 3 Step 5. See page 2 for parts diagram Router Install Pages MLCS Marvel 60 7-8-9 MLCS Marvel 62 10-11-12 For Parts or Installation Assistance Contact...
  • Page 2 Page 1 METRIC EQUIVILANTS FOR INTERNATIONAL CUSTOMERS Note: The following metric drill bit or wrench sizes may be substituted for all operations other than drilling hole for #30 Dust Cover Insert. 1/8” = 0.125" 3.20mm = 0.126" 3/32" = 0.093 2.4mm = 0.094 5/32"...
  • Page 3 Page 2...
  • Page 4: Installation

    ( After installation you will have extra parts ) Thisl kit contains parts for all MLCS Marvel routers. Each instruction page lists the parts required for installation into that router. We advise keeping and storing all the extra parts and instructions.
  • Page 5 Page 4 Using the #46 Locating Pin Use this pin to simplify locating the Router Raizer access hole required through the original subbase or router table. Locating Hole in Original Subbase Original Subbase or Router Table Using fig 1 support router upside down on bench and place locating pin into bottom of #1 mainshaft head.
  • Page 6: Troubleshooting

    Using Paper Drilling Template Page 5 Router table fence reference line Place paper template lettering up onto top side of router table or inset plate. Router table fence reference line. Setting this line parallel with the back edge of the router table or insert plate positions the router so the Router Raizer access hole will be drilled out in front of the fence.
  • Page 7 Router Raizer Use Instructions Page 6 Caution: Always make sure router switch is in the off position, and tool is disconnected from power source when performing maintenance or making any adjustments to either the router or height adjustments to avoid accidental starting of tool which may result in personal injury. Using in a Router Table Insert Plate fig 1...
  • Page 8 MLCS Marvel 60 NOTE: Check Off Each Step When Done Page 7 TOOLS REQUIRED: Phillips screwdriver, straight screwdriver, hammer, 12.8mm or 1/2" and 8mm drill bits. ROUTER RAIZER PARTS REQUIRED: #1, #7, #9, #10, #12, ( #13 for insallation tool only,) #14, ( three of #15 ) #18, #19, #21, #22,...
  • Page 9 Page 8 MLCS Marvel 60 Select #12 green bushing ( Two #15 retainers ) #21 lead screw, #22 rapid collar, #23 O-ring, #24 thumb screw, fig 7 #26 top drive, #27 yellow set screw, #28 Allen wrench, red grease. Using ( fig 6 ) place grease on threads of...
  • Page 10 NOTE: This hole must be drilled 1/2" or .500" insert plate. for #30 dust cover insert to fit properly. MLCS Marvel 60 Use this 6" scale to check accuracy when copied Note: Cross lines for locating and drilling holes are accurate. The illustration of subbase may vary slightly in size and design, but is accurate enough for cutting the rubber gasket if required.
  • Page 11 MLCS Marvel 62 NOTE: Check Off Each Step When Done Page 10 TOOLS REQUIRED: Phillips screwdriver, straight screwdriver, hammer, 1/2" and 5/16" drill bits. ROUTER RAIZER PARTS REQUIRED: #1, #7, #10, #12, ( #13 for installation tool only,) #14, ( three of #15 ) #18, #19, #21, #22, #23, #24, #26, #27, #28, #29, #40 .
  • Page 12 Page 11 MLCS Marvel 62 Installing #1 Mainshaft Place small amount of included red grease onto both sides of #7 brass washer ,place washer down #1 mainshaft. Slide mainshaft through #12 green bushing until flush with base. Stand base upright place #14 3/16 steel washer onto #1 mainshaft drop into the post. Select #13 hollow spring bushing, place #15 retainer clip teeth up onto the top of the mainshaft.
  • Page 13 NOTE: This hole must be drilled 1/2" or .500" insert plate. for #30 dust cover insert to fit properly. MLCS Marvel 62 Use this 6" scale to check accuracy when copied Note: Cross lines for locating and drilling holes are accurate. The illustration of subbase may vary slightly in size and design, but is accurate enough for cutting the rubber gasket if required.

This manual is also suitable for:

Marvel 62