Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Sea King 1500-HD
- Page 1 ® Gyro Stabilized Satellite TV Antenna Model 1500-HD Model 1800-HD Installation and Operating Instructions ® Digital TV Solutions for Mobile Markets 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (952) 922-6889 Fax: (952) 922-8424 www.kingcontrols.com MEMBER 20339 REV G...
-
Page 3: Table Of Contents
The satellite TV market is expanding and changing. The information in this manual was accurate at the time of printing. If your Sea-King does not operate as outlined in this manual please call King Controls at (952) 922-6889 or visit our website at www.kingcontrols.com. -
Page 4: Introduction
INTRODUCTION SECTION 1 The Sea-King Fully Stabilized Marine Satellite System includes 6 main components (Fig. 1). Dome (Antenna) Unit Mounted on the vessel. The dish is covered by a protective dome that keeps operational components free from the elements. Controller Located in the vessel. -
Page 5: Definition Of Terms
DEFINITION OF TERMS SECTION 2 AZIMUTH: Angle in degrees measured clockwise from Magnetic North (0°) (Fig. 2). Fig. 2 ELEVATION: Angle in degrees measured from a level plane (Fig. 3). Fig. 3 SIGNAL STRENGTH: Intensity of electronic signal received from the satellite transmission. Page 3... -
Page 6: Installation
INSTALLATION SECTION 3 TOOLS AND MATERIALS REQUIRED • drill and drill bit set • tape measure • 7/16” open end wrench (coax connections) • 5/32” allen wrench, channel lock or pliers (to remove shipping bolt) • 1/8” allen wrench or phillips screw driver (to remove dome cover) •... - Page 7 The shortest distance between the dome unit and the main satellite receiver is most desirable. b) The dome unit requires a 16.5” (model 1500-HD) or 20” (model 1800-HD) diameter mounting area on the vessel surface. You may also use an industry standard mount.
- Page 8 2. Place the components in the selected areas. REMOVE SHIPPING RESTRAINTS Note: Reference appropriate figure on next page for your model number: Model 1500-HD: see Fig. 6A Model 1800-HD: see Fig. 6B 1. Remove and save the dome cover screws (Figs. 6A and 6B).
- Page 9 Fig. 6A 1500-HD IMPORTANT! The shipping bolt must be removed prior to installation. IMPORTANT! CAREFULLY remove the dome cover. Do not allow dome cover to catch on internal components or wiring. Fig. 6B 1800-HD IMPORTANT! The shipping bolt must be removed prior to installation.
- Page 10 EXTREMELY IMPORTANT! NEVER lift the unit by the LNB assembly, Wave Guide assembly, or the dish. Lift the unit by the base ONLY. PRE-INSTALLATION CHECK To verify proper operation of the components, perform a Pre-Installation Check as follows: 1. Place the dome unit in your chosen location and on its mounting pedestal. Temporarily secure the unit from falling.
- Page 11 COIL AND STORE EXCESS CABLE IN THE CABINET WITH THE COMPONENTS. DO NOT CUT COAX. If coax cable other than that supplied with the Sea-King is used, the following guidelines must be followed: 1) Ends must be terminated with SNAP-N-SEAL ®...
- Page 12 Fig. 8 Note: The Sea-King is wired for multiple receiver support. There are two coax ports on the bottom of the dome unit. The one labeled “MAIN” MUST be connected to the Tuner (IDB) in vessel. The unlabeled port can be used for an additional receiver (see page 13).
- Page 13 3. Fill end of coax cable that will connect to the MAIN port on the antenna unit with supplied dielectric grease. Connect this end of the coax cable to the MAIN port and tighten connection (Fig. 9). If using a second (auxiliary) receiver, fill end of second coax cable and connect it to the unlabeled port.
- Page 14 ELECTRICAL HAZARD WARNING! The coax cable that connects the dome unit to the tuner carries a 24 volt electrical current. Exercise extreme caution when handling this cable. Do not cut, break, or splice this line. Do not insert or connect any devices such as splitters or any other device for any reason.
- Page 15 Fig. 10 DISH Network/Bell TV Sea-King 1500-HD & 1800-HD Auto-switching from master receiver only Note: In order to view programming from the master and secondary receivers simultaneously, both receivers must be tuned to a channel broadcast from the same satellite. Use the controller to manually switch satellites for the secondary receiver.
- Page 16 Fig. 11 DIRECTV Installation Sea-King 1500-HD & 1800-HD Auto-switching from any receiver Note: To automatically switch between satellites using any receiver, tune all other receivers to channel 202 on the 101 satellite. IMPORTANT! HDTV Converter must be hooked to 18V input on multi-switch.
- Page 17 This page intentionally left blank. Page 15...
- Page 18 OPTIONAL WALL MOUNT FACEPLATE (INCLUDED) Note: If not using the faceplate, see faceplate removal instructions below. IMPORTANT! Depending on the thickness of the vessel wall, a relief notch may need to be cut for the cable. THE CABLE MUST NOT BE PINCHED OR BENT WHEN MOUNTING THE DISPLAY. 1.
- Page 19 TUNER MOUNTING OPTIONS You can mount the tuner or leave it freestanding: a) You can mount the tuner to an appropriate surface (Fig. 14). b) You can leave the tuner freestanding. If space requirements dictate, the mounting feet can be snapped off. Fig.
-
Page 20: Operation
Note: This example is for the DTV 101 satellite in Region 2-North Central. The information on your controller will vary depending on the satellite and region you have chosen (see pages 20-21). Note: The Sea-King must remain powered on to maintain a signal. If you are going to be stationary and wish to continue watching TV, DO NOT TURN THE SYSTEM OFF. - Page 21 DIRECTV: Before using the automatic switching feature, you must configure the Sea-king and your receiver for your desired option. For switching options see pages 22-23. DISH Network - Bell TV: Before using the automatic switching feature, you must configure the Sea-King and your receiver for your desired option. For switching options see page 25.
- Page 22 SET SATELLITE SERVICE IMPORTANT!: If you choose any DISH Network or Bell TV option in steps 1-3 below, you must then run the check switch on pages 26-27. All of the satellite options listed may not be available with your unit. If you cannot lock onto your chosen satellite(s), call the King Controls Service Department.
- Page 23 SET REGION (OPTIONAL) Note: To reduce satellite acquisition time, you can set your current region. REGION OPTIONS: NORTH WEST NORTH CENTRAL NORTH EAST CENTRAL WEST MIDDLE CENTRAL CENTRAL EAST SOUTH WEST SOUTH CENTRAL SOUTH EAST ALL REGIONS RECALIBRATE Page 21...
-
Page 24: Automatic Satellite Switching: Directv
101°, 110° and 119° with the properly installed HD converter accessory. It will not receive channels broadcast from DIRECTV’s Ka band satellites at 99° and 103°. With the properly installed HDTV Converter and multi-switch (included), this Sea-King will allow you to receive the specially formatted HD signals from DIRECTV’s 110 satellite and automatically switch between satellites 101/110 or 101/119 when simply changing channels (see the next page for instructions). - Page 25 SEA-KING CONFIGURATION: HD PROGRAMMING FROM THE 110 SATELLITE IMPORTANT! Select your current region first. Failure to select your current region may result in extraordinary delays in channel acquisition (see page 21). 1. Make sure your current region is selected (see page 21).
- Page 26 This page intentionally left blank. Page 24...
-
Page 27: Bell Tv
(May not be available in all areas due to service provider limitations.) The Sea-King will automatically switch between the 82 and 91 satellites for Bell TV by using the receiver’s remote control, after the receiver has been properly configured. Choose BEV 82/91 (see page 20) and follow the instructions on pages 26-27. -
Page 28: Check Switch Procedure
IMPORTANT! The antenna must be on the ground, dock or motionless platform with no movement in order to configure the DISH HD receiver. If you are an end user and the Sea-King is already permanently mounted, you can perform the configuration if the vessel is tied up tightly with no movement. - Page 29 6. When test is complete, a screen similar to ALL SINGLE SATELLITES one of the following should appear: (Screen graphics may vary.) NO SWITCH DETECTED INSTALLED DEVICE UNKNOWN DISH 500 BELL TV 82/91 MUST SHOW “SW21” NO “X”s DISH 1000 DISH 1000a NO “X”s MUST SHOW...
-
Page 30: Troubleshooting
TROUBLESHOOTING SECTION 8 SYMPTOM POSSIBLE SOLUTION Controller does not power up. Check: tuner is connected to power supply. controller is connected to tuner. power supply is plugged into 110 VAC outlet. Controller remains in one of the Unplug tuner for 10 seconds, then plug back in. following conditions: Check coax cables and connections between tuner and dome unit. - Page 31 SYMPTOM POSSIBLE SOLUTION Only getting signal on 1/2 of Kinked or sharply bent coax cable. transponders. Verify coax cables are properly terminated with SNAP-N-SEAL ® connectors only. Verify receiver is operating properly. Verify LNB type is set correctly. Unit never locks on or locks on Atmospheric moisture.
- Page 32 OPTION 21 RE-INITIALIZE and 0-RECALIBRATE Page 30...
- Page 33 Page 31...
-
Page 34: Maintenance
MAINTENANCE SECTION 9 The Sea-King Satellite System has been designed to be maintenance and trouble free. For optimum signal strength, keep the dome clean from dirt, bugs, and other debris. Periodic washing of the dome with mild soap and water is recommended. -
Page 35: Limited Warranty
LIMITED WARRANTY SECTION 10 Every new King Controls Satellite System is thoroughly inspected and tested before leaving the factory, and is covered by the following two year parts and one year labor limited warranty from the date of original purchase: •... - Page 36 Notes: Page 34...
- Page 37 Notes: Page 35...
- Page 38 Notes: Page 36...
- Page 40 ® 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (952) 922-6889 Fax: (952) 922-8424 www.kingcontrols.com...