Table of Contents
Advertisement
Quick Links
ARAG
Series 466 Console
®
Operating Instructions and Parts Manual
Series 466 Console
These sprayer consoles allow the operator to
monitor and control boom pressure and control each
boom section. These controls can be easily mounted in
the sprayer and tractor cabs. Control valves are kept on
the sprayer frame.
Features:
• Sealed switches
• High brightness LED indicators
• Master valve and pressure regulating switches
• General protection fuse, automotive type
• Switches tested to last more than 100,000 cycles
• 12 VDC operation
• Liquid-filled pressure gauge, 2.5" diameter with rear connection
Description
Part Number
4665-3-OP100-3
4665-3-OP300-3
4665-5-OP100-5
4665-5-OP300-5
All part numbers include: power cables, 10' extension
cable, 16.5' boom section output cables, pressure gauge,
connection hose and fittings.
Form 1481
Sections
Gauge
3
100 psi
3
300 psi
5
100 psi
5
300 psi
7-03
Advertisement
Table of Contents
Summary of Contents for Hypro ARAG Series 466
- Page 1 Form 1481 7-03 ARAG Series 466 Console ® Operating Instructions and Parts Manual Description Series 466 Console Part Number Sections Gauge These sprayer consoles allow the operator to 4665-3-OP100-3 100 psi monitor and control boom pressure and control each 4665-3-OP300-3 300 psi boom section.
- Page 2 Warning! Read the instructions in this manual carefully. Hypro/ARAG cannot be held responsible for damage caused by improper use or installation. PRECAUTIONS: 1. Never spray the console with a pressure washer. 2. Never use solvents for cleaning. 3. In case of electric welding, make sure that the power supply to the console is disconnected. If necessary, disconnect the battery cables.
- Page 3 Installation Continued To avoid the risk of short circuits, do not connect the power supply cable until the installation has been completed. WARNING: Make sure that the voltage of the tractor battery is the same as that of the switch box (12Vdc). Fig.
- Page 4 Instructions for Wiring 466 Series Consoles to Non-Hypro/Arag Valves WARNING: Non-Hypro/Arag valves typically draw more amps. Do not exceed a total amp draw capability of 10 amps. WARNING: Modifying cable harnesses will void the warranty. Three-wire boom section valves (motorized ball valves) 1.
- Page 5 Instructions for Wiring 466 Series Consoles to Non-Hypro/Arag Valves Two-wire solenoid valves 1. See Fig. 5 for wiring schematic. 2. Use standard flat spade connectors to insert into DIN connector. 3. Secure and seal with electrical tape. Fig. 5 Two-wire solenoid valves Two-wire regulating valves 1.
-
Page 6: Troubleshooting
4. The pressure regulating valve Polarity of “P” cable Check the polarity of the power works in the opposite direction. reversed. supply cable B in Fig. 6. For non- Hypro/ARAG valves, reverse the spades in the DIN connector. - 6 -... - Page 7 Parts Breakdown SPARE PARTS Fig. 6 COMPLETE CONSOLE ONLY Part Number 46625CPV02-910 COMPLETION CABLES Part Number 466550-080 466530-090 466550-090 466530-230 466550-230 Number of Sections Description power cable extension cable extension cable boom section cable boom section cable Meters Feet 16.5 16.5 - 7 -...
- Page 8 LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Hypro’s obligation under this warranty is, at Hypro’s option, to either repair or replace the product upon return of the entire product to the Hypro factory in accordance with the return procedures set forth below. THIS IS THE EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY.
Need help?
Do you have a question about the ARAG Series 466 and is the answer not in the manual?
Questions and answers