Subscribe to Our Youtube Channel
Summary of Contents for Smarter tools 38PC
-
Page 1: Spray Gun
38PC GRAVITY FEED SPRAY GUN Operating Manual Revision: AB Issue Date: January 2012 Manual No.: 0-GF-38PCKIT0112... - Page 2 We Appreciate Your Business. Thank you and congratulations on choosing Smarter Tools. Now you can stop working harder and start working smarter. This Operating Manual has been designed to instruct you on the correct use and operation of your Smarter Tools’ product. Your satisfaction with this product and its safe operation is our ultimate concern.
-
Page 3: Safety Instructions And Warnings
Description The Smarter Tools 38-Piece Gravity Feed Spray Gun Kit includes the spray guns you need for automotive, furniture and equipment painting. Kit includes a gravity- feed spray gun with 550ml canister, touch-up spray gun with 120ml canister, air adjusting valves with gauges, cleaning kit, paint filters and bonus blow mold storage case. -
Page 4: General Safety Information
Unpacking After unpacking the product, inspect carefully for any damage that may have occurred during transit. Make sure to tighten fittings, bolts, etc., before putting unit into service. WARNING! DO NOT OPERATE TOOL IF DAMAGED DURING SHIPPING, HANDLING OR USE. DAMAGE COULD RESULT IN BURSTING AND CAUSE INJURY OR PROPERTY DAMAGE. - Page 5 WARNING! DO NOT MISUSE THIS PRODUCT. EXCESSIVE EXPOSURE TO VIBRATION, WORK IN AWKWARD POSITIONS, AND REPETITIVE WORK MOTIONS CAN CAUSE INJURY TO HANDS AND ARMS. STOP USING ANY TOOL IF DISCOMFORT, NUMBNESS, TINGLING OR PAIN OCCUR, AND CONSULT A PHYSICIAN. 4.
- Page 6 Introduction The spray gun is a vital link in any finishing application. In addition to operating the spray gun properly, techniques of surface preparation and paint preparation must be understood. These instructions will explain the differences among various spray technologies and serve as a guide in the proper operation and techniques of spray painting.
- Page 7 used with this method. Pressure feed is generally used for spraying heavy bodied paints or for large size projects. Siphon Feed – Method of paint feed where atmospheric pressure creates a partial vacuum to siphon paint to the gun. Only external mix air caps are used with this method.
- Page 8 Air Tool and Spray Gun Set-up Conexiónes de las Herramientas Neumáticas y Pistolas Pulverizadoras...
-
Page 9: Fan Direction
PREPARATION 1. Thoroughly mix and thin paint in accordance with the paint manufacturer’s instructions. Most materials will spray readily if thinned properly. 2. Strain material through cheese cloth or a paint strainer. 3. Fill the canister about 3/4 full and start the air compressor. 4. -
Page 10: Operation
3. Turn fluid control knob fully clockwise until closed (See Figure 6). 4. Trigger a short burst while turning fluid control knob counterclockwise. Observe the spray pattern on the target and adjust the fluid control knob until the desired pattern (atomization) is obtained (See Figure 7). -
Page 11: Maintenance
4. The amount of paint being applied can be varied by the speed of the stroke, distance from the surface and adjustment of the fluid control knob. 5. Overlap strokes just enough to obtain an even coat (See Figure 11). NOTE: Two thin coats of paint will yield better results and have less chance of runs than one heavy layer. - Page 12 3. Remove the air cap and soak in solvent until clean. Use a small brush for stubborn stains if necessary. Toothpicks or small brushes may be used to clean air passages; however, NEVER USE METAL OBJECTS TO CLEAN PRECISELY DRILLED PASSAGES. DAMAGED PAS- SAGES WILL CAUSE IMPROPER SPRAYING.
- Page 13 tighten a packing nut because this will restrict movement of the needle. 6. Re-assemble in reverse order of above and use a non-silicone oil on moving parts. Apply Vaseline® or light grease on threaded joints and hose connections. STORING 1. When not using spray gun, turn the fluid adjustment knob counterclockwise to open which will reduce spring tension on needle fluid tip.
-
Page 14: Limited Warranty
No employee, agent, or representative of Smarter Tools is authorized to change this warranty in any way or grant any other warranty, and Smarter Tools shall not be bound by any such attempt. Correction of non-conformities, in the manner and time provided herein, constitutes fulfillment of Smart Tools’... -
Page 15: Garantía Limitada
Smarter Tools, tanto si se producen fuera de contrato, acto ilícito, incluida la negligencia o responsabilidad estricta, o bajo cualquier garantía, o de lo contrario, no podrá...
Need help?
Do you have a question about the 38PC and is the answer not in the manual?
Questions and answers