Table of Contents
Advertisement
Quick Links
ASX / OUTLANDER SPORT / RVR
INSTALLATION AND HANDLING INSTRUCTIONS
Navigation (MMCS) unit
Thank you for purchasing the Mitsubishi Genuine Accessory.
To install and use the product correctly with proper knowledge of it, read this publication carefully.
Keep this publication for reference when maintenance is required.
・This publication gives precautionary instructions in the boxes titled as follows.
Read through these instructions thoroughly.
・Failure to follow these instructions not only prevents the product from working properly but may lead to trouble
with the vehicle. Be sure to follow all instructions carefully.
・If there is anything unclear about the installation, handing and/or usage of the product, contact your Mitsubishi
Motors dealer for clarification.
・Mitsubishi Motors Corporation is not responsible for any defects or difficulties caused by or resulting from the
failure to follow given instructions.
・We recommend you to have the installation performed at an authorized Mitsubishi Motors dealer.
To the dealer:
Be sure that the customer receives this publication.
REAR VIEW CAMERA
MZ380552EX
Describes precautions that should be observed in order to prevent injury or damage
to the vehicle or its components, which may occur if sufficient care is not taken.
Provides additional information that facilitates installation work.
Attention
1
Camera
ＪＩ２６１３７３
１０．７
Advertisement
Table of Contents
Summary of Contents for Mitsubishi MZ380552EX
- Page 1 ・Failure to follow these instructions not only prevents the product from working properly but may lead to trouble with the vehicle. Be sure to follow all instructions carefully. ・If there is anything unclear about the installation, handing and/or usage of the product, contact your Mitsubishi Motors dealer for clarification.
-
Page 2: Required Components
TOOLS （Make the following tools ready for use.） Socket wrench Philips screwdriver Flat-blade screwdriver Trim remover Utility knife Scissors Wire Cloth tape Vinyl tape COMPONENTS (Make sure that all of the following components were included in the kit.) ①... -
Page 3: Before Installation
Before installation When installing or removing parts Loosen or tighten bolts Use a Phillips screw- To remove plastic Be sure to disconnect the negative terminal and nuts using tools driver that fits the parts, use a trim that match their sizes. recess in the head of remover. - Page 4 PRECAUTIONS Be sure to apply the parking brake securely. Remove the ignition key from the key cylinder . When removing and reinstalling the vehicle parts, perform the work including the tightening torques in accor- dance with the workshop manual. Disconnecting the (–) cable from the battery causes the radio and audio presets, the clock, etc.
- Page 5 B. Wiring of Camera Cable B-1. Preparation for Wiring Camera Cable (1) Wrap the camera cable (around the pin terminal) with vinyl tape up to the cable end for protection. Vinyl Tape Caution Camera Cable Be careful not to bend or break the terminal Pin Terminal when wrapping the cable with protective vinyl tape.
- Page 6 For Right-hand Drive Vehicle Connection of Camera Cable Terminals (1) Disconnect a 24P connector from the navigation. White Disengage stoppers on the 24P connector. Insert camera cable terminals into the 24P connector as shown in left-hand illustration. Caution Be careful not to connect terminals Blue Transparent Black 24P Connector mistakenly.
- Page 7 B-3. Wiring of Camera Cable to Vehicle Rear For Left-hand Drive Vehicle For Right-hand Drive Vehicle Cable Tie Cable Tie Camera Cable Camera Cable (1) Wire the camera cable to the navigation attachment area. Fix the camera cable to the vehicle harnesses with cable ties. (2) Wire the camera cable on the left side of vehicle along vehicle harnesses toward the rear.
- Page 8 (3) Wire the camera cable on the left side of vehicle along vehicle harnesses toward the rear. Fix the camera cable to vehicle harnesses with cable ties. Cable Tie Cable Tie (4) Wrap the camera cable with half-cut urethane tape. (5) Flip the edge of the roof lining slightly and wire the camera cable inside the roof lining.
- Page 9 Connection of Camera Cord Terminals Remove the stopper from the 6P coupler. Insert camera cable terminals into the 6P coupler as shown in illustration below. Caution Be careful not to connect terminals Transparent White mistakenly. Blue It may cause malfunction. Joint Surface Joint Surface Side View Attach the stopper.
-
Page 10: Connecting Diagram
Connecting Diagram For Left-hand Drive Vehicle For Right-hand Drive Vehicle MMCS MMCS Connector for Camera 24P Connector Camera Cable Camera Cable Rear View Camera Rear View Camera... -
Page 11: Operation Confirmation
C. Reinstallation of Vehicle Parts Refer to workshop manual for how to reinstall removed vehicle parts. Operation Confirmation (1) Ensure that all the connections have been properly performed according to the connecting diagram. (2) Check for the battery and turn the ignition switch to the IGN position. (3) Confirm the state of connection and operation according to the operation manual.