Summary of Contents for M2M C600
- Page 1 Technical Manual 1.05, C600 Professional Technical Manual M2M Control C600 Professional Version 1.05...
-
Page 2: Introduction
GSM activity, change of digital inputs or a vibration sensor! These features open up for the use of the C600 Professional in exciting new application areas where extremely low power consumption and flexible wake-up conditions are a crucial parameter for successful product integration. -
Page 3: Table Of Contents
DIP-Switch ........................19 Reset-Switch ........................19 Internal Li-Ion battery ......................20 Vibration Sensor ........................20 Specifications for the C600 Professional ................21 Specifications for the 16-channel GPS receiver..............22 Appendix A – Enabling the CAN bus Write capability ............23 Page 3 of 24 M 2 M C o n t r o l Ph: +49.40.69647-260... -
Page 4: Graphical View
Technical Manual 1.05, C600 Professional Graphical view Page 4 of 24 M 2 M C o n t r o l Ph: +49.40.69647-260 by Infranet Technologies GmbH Tempowerkring 2 Fax: +49.40.69647-259 21079 Hamburg Email: info@m2mcontrol.de Germany Web: www.m2mcontrol.de... -
Page 5: External Connections
Technical Manual 1.05, C600 Professional External connections Overview Connections to external equipment are done via the connectors located back and forth on the product. All connections are available externally for easy access; this also includes SIM-Card and SD-Card. There are no user-serviceable parts inside and the warranty is void if the unit is disassembled. - Page 6 Technical Manual 1.05, C600 Professional Connector X1: 4 pin (Power) connector overview. Name Description SUPP Power supply, positive (+) connection DI5/IGN Digital input 5 / Ignition input (Shared with 16 pin connector) SUPP Power supply, positive (+) connection PGND Power Ground Connector X2: 12 pin (Communication) connector overview.
- Page 7 Signal Ground Receive data to Serial port 2 Transmit data from Serial port 2 Clear To Send Request To Send Accessories available from M2M Control for cable assembly. Order-code Name RT-O-TYCO-H4 TYCO, Connector house 4 pins. Bag with 10 pcs...
-
Page 8: Power Supply
M2M Control IDE online help for more information. When the ignition input is activated with a logical high, the C600 unit will wake-up if it was in power down mode. The ignition input (digital input 5) is available on the power... -
Page 9: Digital Outputs
The digital outputs control four “high-side” switches. They function like a contact, where one side is connected to the positive supply of the C600 unit, and the other is the output. The switches are protected against short circuit, ESD and electronic kickback from inductive loads such as relays etc. - Page 10 Technical Manual 1.05, C600 Professional X3: 16 pin (I/O) connector overview. Name Description DIN 1 Digital input 1 DIN 2 Digital input 2 DIN 3 Digital input 3 DIN 4 Digital input 4 DIN 5/IGN Digital input 5 / Ignition input. (Shared with 4 pin connector)
-
Page 11: Analog Inputs
RS-DET pin must be connected to GND. When using the port as general-purpose RS232, the RSDET pin must be left unconnected. Further details on the programming cable are available in the M2M Control IDE online help. -
Page 12: Serial Port 2
The serial port 2 is a general-purpose RS232 port with all control signals according to EIA- 561 that defines RS-232 on a modular connector. The signals are available on the RJ45 connector located on the front plate of the C600. RJ45 (Serial port 2) connector overview. -
Page 13: Can
CAN-H and CAN-L at each end of the transmission-line to terminate it and avoid signal reflections. Be aware that connecting the C600 to a CAN network can be dangerous. If the C600 is not configured with the correct network parameters, it will lead to network corruption and may interfere with other connected equipment on the bus. -
Page 14: 1Wire
It is recommended to install a fuse to protect the output. This output must be enabled from the application. Please consult the M2M Control IDE online manual for more information. X2: 12 pin (Communication) connector overview. -
Page 15: Headset Connector
Technical Manual 1.05, C600 Professional Headset connector The C600 unit has a 4-pole 2.5mm jack connector for connecting a Nokia compatible headset to the built-in GSM modem. The speaker output is amplified through the internal amplifier and is a differential (balanced) signal. An audio line transformer must be used to convert the signal to a single ended signal, when connected to external equipment that does not have a differential (balanced) input. -
Page 16: Installing The Sim-Card
Technical Manual 1.05, C600 Professional Installing the SIM-card The C600 Professional unit contains a standard SIM card reader. It is located on the front plate (please see the graphical view) and is easily accessed. The SIM card reader has a push/push eject system and a mechanical lock for secure installation of the SIM card. -
Page 17: Installing The Sd-Card
GSM antenna. GPS Antenna The C600 Professional unit contains an SMB Male connector for connection of a suitable GPS antenna. The GPS antenna must be a 3V active GPS antenna mounted with a SMB Female connector. -
Page 18: Indicators (Led's)
The single yellow LED is signaling either the GSM module activity or if all other LED’s are off it will signal that the C600 is in the “wait for event” low power state. Please see the table below:... -
Page 19: Switches
The C600 Professional unit contains a combined reset/diagnostic switch. This switch is located on the front-plate of the C600 unit (see the graphical view). By activating the switch shortly the C600 unit will do a complete reset, as if the power was removed and reapplied. -
Page 20: Internal Li-Ion Battery
100-hour after the last charge. This is to compensate for the battery self-discharge etc. As standard the battery cannot be charged above 45°C or below 0°C. The C600 unit will automatically detect the temperature and terminate the charge process if the temperature is out of this range. -
Page 21: Specifications For The C600 Professional
Technical Manual 1.05, C600 Professional Specifications for the C600 Professional Page 21 of 24 M 2 M C o n t r o l Ph: +49.40.69647-260 by Infranet Technologies GmbH Tempowerkring 2 Fax: +49.40.69647-259 21079 Hamburg Email: info@m2mcontrol.de Germany Web: www.m2mcontrol.de... -
Page 22: Specifications For The 16-Channel Gps Receiver
Technical Manual 1.05, C600 Professional Specifications for the 16-channel GPS receiver u-blox LEA-4A General: 16 Channels simultaneous operation DGPS capable L1 frequency (1575.42MHz) C/A code (Standard Positioning Service) Continuous tracking receiver Update Rate: NMEA @ 1 Hz Accuracy: Position 2.5m CEP DGPS/SBAS 2.5m CEP... -
Page 23: Appendix A - Enabling The Can Bus Write Capability
Technical Manual 1.05, C600 Professional Appendix A – Enabling the CAN bus Write capability Connecting the C600 to a CAN network can be dangerous. If the C600 is not configured with the correct network parameters, it can lead to network corruption and may interfere with other connected equipment on the bus. - Page 24 Technical Manual 1.05, C600 Professional 3. Mount the jumper, as shown on the picture below: 4. Gently push the electronic board back into the encapsulation again. In any case DO NOT USE FORCE. If difficulty is experienced it is because the light-pipes on the...