Noga net NG-192 User Manual
  1. Manuals
  2. Brands
  3. Noga net Manuals
  4. Wireless Router
  5. NG-192
  6. User manual

Noga net NG-192 User Manual

Wireless n router
Hide thumbs
Table of Contents

Advertisement

Quick Links

1

Advertisement

Table of Contents
loading

Summary of Contents for Noga net NG-192

  • Page 2: Table Of Contents

    TABLE OF CONTENT 1. ABOUT THIS GUIDE ................... 4 1.1 Navigation of the User’s Guide ............4 2. PRODUCT OVERVIEW ................5 2.1 Introduction ..................5 2.2 Features ....................5 2.3 Panel Layout ..................6 2.3.1 Front Panel ................. 6 2.3.2 Rear Panel .................
  • Page 3 5.3.9 WPS Settings ................30 5.4 Network ..................... 31 5.4.1 LAN Interface ................31 5.4.2 WAN Interface ................33 5.4.3 WAN Advanced ................ 34 5.5 Firewall ....................35 5.5.1 Rule Filter ................. 35 5.5.2 MAC Filtering ................36 5.5.3 URL Filtering................36 5.5.4 Port Forwarding ................

  • Page 4: About This Guide

    1. ABOUT THIS GUIDE Thank you very much for purchasing this NG-192 Wireless N Router. This guide will introduce the features of this Router and tell you how to connect, use and configure the Router to connect with Internet. Please follow the instructions in this guide to avoid affecting the Router’s performance by improper operation.

  • Page 5: Product Overview

    2. PRODUCT OVERVIEW 2.1 Introduction NG-192 is a combined wired/wireless network connection device that integrates with internet-sharing router and 4-port switch. It complies with the most advanced IEEE 802.11n technology and supports multiple security encryptions, including wireless LAN 64/128-bit WEP, WPA/WPA2, WPA-PSK/WPA2-PSK authentication and TKIP/AES. Besides, IP, URL and MAC address filtering function makes it easy for user management.

  • Page 6: Panel Layout

    2.3 Panel Layout 2.3.1 Front Panel The front panel of NG-192 Router consists of 8 LEDs, which is designed to indicate connection status. This indicator lights blue when the hub is receives power, otherwise it is POWER off. This indicator blinks blue when Router powered on.

  • Page 7: Rear Panel

    2.3.2 Rear Panel The figure below shows the rear panel of NG-192 router. The Power socket is where you will connect the power adapter. DC IN RST: With the router powered on, use a pin to press and hold the button until the SYS LED becomes quick-flash from slow-flash.

  • Page 8: Hardware Installation

    3. HARDWARE INSTALLATION 3.1 Unpacking Please open the box of NG-192 Wireless N Router carefully. The box should contain items listed below: One NG-192 Wireless N Router  One Power Adapter  One Quick Installation Guide  One CD-ROM (User’s Guide) ...
  • Page 9 Connect the local PC to the LAN port on the Router. There are then two ways to configure the IP address for your PC. Configure the IP address manually  1. Set up the TCP/IP Protocol for your PC. 2. Configure the network parameters. The IP address is 192.168.0.xxx (“xxx” range from 2 to 254).

  • Page 10: Connecting To Internet

    If the result displayed is similar to that shown in the above figure, it means that your PC has not connected to the Router successfully. Please check it following below steps: 1. Is the connection between your PC and the Router correct? If correct, the LAN port on the Router and LED on your PC’s adapter should be lit.

  • Page 11: Changing Password

    Now you have logged into the web interface of the router. 4.2 Changing Password First, we recommend that you change the password to protect the security of your router. Please go to Management—Password change the password required to log into your router.

  • Page 12: Setup Wizard

    4.3 Setup Wizard Setup Wizard is provided as part of the web configuration utility. Users can simply follow the step-by-step process to get the wireless Router configuration ready to run in 6 easy steps by clicking on the Setup Wizard on the left navigation menu. Then the following screen will appear.

  • Page 13: Gateway

    4.3.1.1 Gateway Generally, this operating mode is selected by default as more and more users choose to access Internet by ADSL/Cable Modem. In this mode, the device works as a Software Router of the LAN, all clients will connect to Internet through this “agent”. If you choose this mode, PCs in four LAN ports share the same IP to ISP through WAN port.

  • Page 14: Lan Interface

    Enable NTP client update: NTP means Network Time Protocol which is used to make the computer time synchronized with its server or clock source, such as Quartz and GPS. It can provide high-precision time correction and prevent harmful protocol attack by confirming encryption.

  • Page 15: Static Ip

    4.3.4.1 Static IP If your ISP has provided the fixed IP that allows you to access Internet, please choose this option. IP Address: the IP address provided by your ISP. Subnet Mask: This is used to define the device IP classification for the chosen IP address range.

  • Page 16: Pppoe

    4.3.4.3 PPPoE Point-to-Point Protocol over Ethernet (PPPoE) is a virtual private and secure connection between two systems that enables encapsulated data transport. It replies on two widely accepted standards: PPP and Ethernet. It connects users through an Ethernet to the Internet with a common broadband medium, such as wireless device or cable modem.
  • Page 17 Band-- In fact, this option allows you to choose the radio standard for operation of your Router. 802.11b and 802.11g are old 2.4GHz mode, while 802.11n (2.4GHz and/or 5GHz, in this case, only supports 2.4GHz) is the latest standard based on faster Orthogonal Frequency Division Multiplexing (OFDM) modulation.

  • Page 18: Security Settings

    Infrastructure: This mode allows Wireless LAN and wired LAN to communicate with each other by one AP. The wireless network bridges to wired network by this mode. If you choose this type, you can’t edit Channel Width and Channel Number. Ad hoc: This mode allows two or more computers with wireless function to send/receive messages from each other.

  • Page 19: Wep

    4.3.6.1 WEP WEP (Wired Equivalent Privacy) is based on the IEEE 802.11 standard and uses the RC4 encryption algorithm. Enabling WEP allows you to increase security by encryption data being transferred over your wireless network. WEP is the oldest security algorithm, and there are few applications that can decrypt the WEP key in less than 10 minutes.
  • Page 20 during data transmission. It has two formats: Passphrase and Hex (64 characters). Then you need to enter the Pre-Shared Key, either 8~63 ASCII characters, such as 012345678..(or 64 Hexadecimal digits leading by 0x, such as “0x321253abcde…”). After all the above settings, please click Finished button, then page with below messages will pop up: Now you can surf Internet and enjoy the best wireless experience brought by this router.

  • Page 21: Advanced Settings

    5. ADVANCED SETTINGS This chapter allows users to configure advanced settings includes Wireless, Network, Firewall and Management. These settings are only for more technically advanced users who have sufficient knowledge about wireless LAN. Also they should not be changed unless you know what effect the changes will have on your wireless router.

  • Page 22: Operation Mode

    Attain IP Protocol: display the way to get IP Address. IP Address: display the IP address of the LAN interface. Subnet Mask: show the subnet mask address of the LAN interface. Default Gateway: this is the IP address of the router. DHCP: display the current status of DHCP server of the LAN interface.

  • Page 23: Wireless

    5.3 Wireless The general wireless settings, such as 802.11 modes, SSID and data rates can be configured in this section. Also some more advanced settings can be setup here. 5.3.1 Wireless Status This page displays the current wireless status of the router. 5.3.2 Basic Settings On this page, you could configure the parameters for Wireless LAN clients that may connect to your Access Point.
  • Page 24 Country: please choose the country where you’re located. By default, it is Argentina. Band: this option allows you to choose the radio standard for operation of your Router. 802.11b and 802.11g are old 2.4GHz mode, while 802.11n is the latest standard based on faster Orthogonal Frequency Division Multiplexing (OFDM) modulation.
  • Page 25 Network Type: specifies the network type for your device. How to select one of them depends on whether the wireless network need to share data or peripherals with wired network. Infrastructure: this mode allows Wireless LAN and wired LAN to communicate with each other by one AP.

  • Page 26: Repeater Settings

    Enable MAC Clone: MAC address is the physical address of your computer’s network card. Generally, every network card has one unique Mac address. Since many ISPs only allow one computer in LAN to access Internet, users can enable this function to make more computers surf Internet.

  • Page 27: Advanced Settings

    802.1x Authentication: if you check this box, you need to provide the below information: RADIUS Server IP Address: enter the IP address of RADIUS server. RADIUS Server Port: the UDP port number that the RADIUS server that is used to authenticate the messages sent between them.
  • Page 28 access point, helps control traffic flow. The range is 0-2347 bytes. The default value is 2347, which means that RTS is disabled. RTS/CTS (Request to Send / Clear to send) are the mechanism used by the 802.11 wireless networking protocols to reduce frame collisions introduced by the hidden terminal problem.

  • Page 29: Multiple Aps

    value is 100%. It will deliver the best performance of the device. 5.3.6 Multiple APs This page allows you to set multiple APs. 5.3.7 Access Control Access Control Mode: you could select Allow List or Deny List according to your requirement.

  • Page 30: Wps Settings

    Only if you have chosen WDS/AP+WDS mode, you can enable this function. MAC Address: the other AP’s MAC Address that you want to communicate with. Data Rate: please choose the transmission data rate. Comment: describes the reason why you want to communicate with others. Set Security: click this button you can set security rules for WDS.

  • Page 31: Network

    WPS Status: Display related system information for WPS. If the wireless security (encryption) function of the router is properly configured, you can see “Configured” chosen. By default, it is UnConfigured selected. Self-PIN Number: it will show the PIN Number of your device. Push Button Configuration: click Start PBC to invoke Push-Button style WPS setup procedure.
  • Page 32 IP Address: this is the IP addresses to be represented by the LAN (including WLAN) interface that is connected to the internal network. This IP will be used for the routing of the internal network (it will be the Gateway IP for all the devices connected on the internal network).

  • Page 33: Wan Interface

    This page allows you reserve IP addresses, and assign the same IP address to the network device with the specified MAC address any time it requests an IP address. This is almost the same as when a device has a static IP address except that the device must still request an IP address from the DHCP server.

  • Page 34: Wan Advanced

    Provider). MTU Size: It means Max Transmit Unit for packet. When using slow links, large packets can cause some delays thereby increasing lag and latency. The default value of DHCP is 1492, for static IP, it is 1500, for PPPoE is 1452, for PPTP/L2TP is 1460. DNS: Domain Name System.

  • Page 35: Firewall

    Enable PPTP pass through on VPN connection Enable L2TP pass through on VPN connection Enable IPv6 pass through on VPN connection 5.5 Firewall While the broadband users demand more bandwidth for multimedia, interactive applications, distance learning, security has been always the most concerned.

  • Page 36: Mac Filtering

    5.5.2 MAC Filtering On this page, you can add some MAC addresses to be filtered to isolate users’ access from wired LAN. You can choose to enable or disable this function according to your needs. If you enable MAC filtering, please provide the below information: MAC Address: you can enter the MAC addresses that you want to filter.

  • Page 37: Dmz

    You can choose to enable or disable this function according to your needs. If you enable Port forwarding, please provide the below information: IP Address: enter the IP address that you want to forward. Protocol: specify the protocol which this filter rule will apply to. Port Range: enter the port range that you want to forward.

  • Page 38: Connection Limit

    5.5.6 Connection Limit IP Range: set the IP range that you need to limit connection. Connection Limit Num: set the connection limit number. The range is from 1 to 50. Connection Limit List: after you click Apply to make the settings work. This table will display the detailed information about the limit.

  • Page 39: Traffic Statistics

    Manual Uplink Speed: you can set the uplink speed for all LAN computers. Manual Downlink Speed: you can set the downlink speed for all LAN computers. Address Type: here you can choose the limit address type. IP Address: if you choose IP address, please enter the IP address range. MAC Address: if you choose MAC, please enter the MAC address or using Scan Mac Address button.

  • Page 40: Ddns

    5.6.3 DDNS DDNS means Dynamic Domain Name System. The ISP often provides you with a dynamic IP address when you connect to the Internet via your ISP. It means that the public IP address assigned to your router changes each time you access the Internet. The Dynamic DNS feature lets you assign a domain name to a dynamic WAN IP address.

  • Page 41: Time Zone Settings

    5.6.4 Time Zone Settings This page allows you to maintain the system time by synchronizing with a public time server over the Internet. Most of the settings on this page we have discussed on P15 Setup Wizard. If you want to change, you can reset here and click Apply to make it work. Current Time: it shows the current time by default.

  • Page 42: System Log

    Enable DoS Prevention: check this box to enable DoS prevention function. This page shows the attack types that DoS prevention function can detect: Whole System Flood: SYN ICMP Smurf Whole System Flood: FIN IP Land Whole System Flood: UDP IP Spoof Whole System Flood: ICMP IP TearDrop Per-Source IP Flood: SYN...

  • Page 43: Upgrade Firmware

    Enable Log: this option enables the registration routine of the system log messages. Be default it is disabled. Below items including system all, wireless, Dos allows you to choose the log type. Enable Remote Log: enables the syslog remote sending function while System log messages are sent to a remote server.

  • Page 44: Password

    Save Settings to File: click Save button to download the current settings of the Access Point to your computer. Load Settings from File: if you want to reload the settings from the file saved before, you could click Choose File button to choose the right file then click Upload button. Reset Settings to Default: this Reset button is provided to allow you to restore the router settings to the default factory settings.

Table of Contents