Advertisement
Quick Links
DesignView
Presentation System
®
SET UP ........................................................................................................... 2
DraPE ............................................................................................................ 3
ImagE ProjEcTIon ....................................................................................... 5
TaKEDoWn ................................................................................................ 10
ScrEEn rEPlacEmEnT ................................................................................. 12
InSTallaTIon ............................................................................................... 13
aPPEnDIX - nEc ProjEcTor................................................................................14
DesignView Presentation System is a product of Skyline Exhibits
Patents Pending
©2011 Skyline Exhibits
Table of ConTenTs
1
SET UP
InSTrUcTIonS
Pn 32675-f
Advertisement
Summary of Contents for Skyline Exhibits DesignView
-
Page 1: Table Of Contents
DraPE ......................3 ImagE ProjEcTIon ..................5 TaKEDoWn ....................10 ScrEEn rEPlacEmEnT ................. 12 rEmoVal ...................... 12 InSTallaTIon ....................13 aPPEnDIX - nEc ProjEcTor................14 DesignView Presentation System is a product of Skyline Exhibits Patents Pending Pn 32675-f ©2011 Skyline Exhibits... - Page 2 DesignView Presentation System ® SET UP before setting up the DesignView Presentation system for the first time, read these instructions carefully. although this product has been designed for safety, injury could occur if certain precautions are not followed. Unpack parts.
-
Page 3: Set Up
24-72 hrs before using the Design- View system. 3) Thread the first pole into the nut, making sure it is straight, or cross threading may occur. Tighten pole down. DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits... -
Page 4: Drape
6) Proceed to thread the second pole into the nut, making sure it is both straight & tight. (corner #2) 7) attach the feet and unfold the frame per set-up instructions. BacK VIEW DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits... - Page 5 Pull hinge to the outside of the frame until you hear 2 clicks and the locking knob is fully engaged. Clicks DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
- Page 6 DesignView Presentation System ® SET UP Repeat step 4 for the last vertical side. Clicks DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
-
Page 7: Image Projection
34” (86 cm) away from the screen. The projector should be placed on the case for the three smallest screen sizes. 3. Plug power cord into projector and aC outlet. DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits... -
Page 8: Image Projection
5. Prepare the remote control by making sure it has batteries. always point the remote control to the active sensor in the front of the projector, to assure it receives the signal. (For details, review the operating guide on the DesignView Presentation System is a product of Skyline Exhibits Patents Pending... - Page 9 (the function key used may vary, depending on the computer.) The most common resolution is 1024 x 768. 9. To adjust from front to rear projection: DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
- Page 10 Use the arrow buttons to adjust the position of the corner. c. Press enTeR when you reach the desired location to exit the adjustment of the corner. DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
-
Page 11: Lamp Indicator
Please note that the manufacturer provides a concise user manual and a more complete manual, in both booklet and cD formats. Follow all the instructions in those manuals, or on the product, for optimum performance. DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits... -
Page 12: Takedown
Repeat with the second side. DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits... - Page 13 DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
-
Page 14: Screen Replacement
2. Pull fabric off the frame starting at the tab or locking knob hinge area. remove the fabric by gently pulling until it is no longer attached. DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits... -
Page 15: Appendix - Nec Projector
6. Continue to work from the center of each section: continue to work from the center of each area to avoid bunching the fabric until the entire rubber strip is completely inserted. DesignView Presentation System is a product of Skyline Exhibits Patents Pending... - Page 16 THe MIRRoR by unlocking the cover lock switch and lifting it to the open position. PlUG PoWeR CoRD InTo PRoJeCToR anD aC oUTleT PoWEr PoWEr corD SWITcH InlET DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
- Page 17 SEnSor locaTIon DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
- Page 18 “TIlT InDICaToR”. If the projector needs to be leveled adjust the projector feet until both tilt indicators are centered. Tilting the projector will move the indicators. The indicators will turn green when the projector is level. DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
- Page 19 4. Should you have trouble after hours you may call our vendor compView at 1-800-248-1090. 5. If you are unable to get the help you need from these resources please call Skyline customer Service at 1-800-328-2725. DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
- Page 20 This can be done by going into the oSm and making the change there or by sending a specific rS232 command to the projector from a computer. DesignView Presentation System is a product of Skyline Exhibits Patents Pending ©2011 Skyline Exhibits...
- Page 21 15 seconds to confirm the change. click Yes to confirm the change; click no or do nothing to revert to your previous setting. DesignView Presentation System is a product of Skyline Exhibits Patents Pending...
Need help?
Do you have a question about the DesignView and is the answer not in the manual?
Questions and answers