Advertisement

DUST COLLECTOR
KC-3105KWRC SEE PAGE 16
MODEL: KC-3105C
INSTRUCTION MANUAL
COPYRIGHT
1999 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
C

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KC-3105C and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for King Canada KC-3105C

  • Page 1 DUST COLLECTOR KC-3105KWRC SEE PAGE 16 MODEL: KC-3105C INSTRUCTION MANUAL COPYRIGHT 1999 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
  • Page 2 To take advantage of this warranty, the product or part must be returned for examination by the retailer. Shipping and handling charges may apply. If a defect is found, KING CANADA will either repair or replace the product.
  • Page 3: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS WHEN USING YOUR DUST COLLECTOR, FOLLOW THE BASIC SAFETY PRECAUTIONS WARNING: To reduce the risk of fire, electric * To avoid injury from accidental starting, unplug shock or injury: power cord before changing or cleaning the filter/dust bag or the chip bag. * Read and understand this owners manual and all the labels on the dust collector before operating.
  • Page 4 SAFETY BEFORE USING YOUR DUST COLLECTOR CAUTION: If using this dust collector to keep 3. WEAR SAFETY GOGGLES. ‘’FORESIGHT IS airborne wood dust in heavy usage within BETTER THAN NO SIGHT’’. Wear safety acceptable limits, you must regularly monitor goggles, not glasses, that comply with ANSI airborne dust and maintain the dust collector to Z87.1.
  • Page 5: General Safety Instructions

    GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS 1. KNOW YOUR TOOL recommended. Wear protective hair covering Read and understand the owners manual and to contain long hair. Roll up long sleeves above labels affixed to the tool. Learn its application the elbows. and limitations as well as its specific potential 12.
  • Page 6: Specifications

    SPECIFICATIONS MOTOR HORSEPOWER............................1-1/2 VOLTAGE ............................110V/220V AMPERAGE ............................12/6A R.P.M................................3450 Hz ..................................60 PHASE ................................1 POLE ................................2 CLASS ................................E AIR SUCTION CAPACITY ......................1200 C.F.M. FAN DIAMETER ..........................9-1/2’’ HOSE DIAMETER ............................5’’ INLET HOSE DIAMETER ..........................4’’ BAG QUANTITY & SIZE......................2@ 20’’ X 32’’...
  • Page 7 YOUR DUST COLLECTOR 1. DUST COLLECTOR BAG 2. DUST FILTER 3. BELT 4. FILTER BAG 5. BASE PLATE 6. INLET COVER 7. CASTER 8. VENTILATION CYLINDER 9. HOSE UNPACKING 1. Finish removing all the contents of the shipping carton. 2. Report any damage to your retailer. 3.
  • Page 8 ASSEMBLY 1. Install the four casters to the under side as illustrated in Fig.1. Do not remove the lock washers and nuts from caster roller shafts; these act as spacers. Insert roller shaft into threaded hole on the underside of the base, turn until it is snug, then tighten nut with wrench.
  • Page 9 ASSEMBLY 5. Install housing (A) to three support brackets (B) using 6 hex. bolts, 12 flat washers and 6 hex. nuts. Make sure the hose opening faces the fan housing. Before attaching the third support bracket, place hanger bracket (C) between the support bracket and the housing, as illustrated in Fig.5.
  • Page 10: Electrical Connections

    ELECTRICAL CONNECTIONS WARNING ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE DUST COLLECTOR DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! THIS DUST COLLECTOR IS RATED 110V/220V AND COMES FROM THE FACTORY PREWIRED AT 110V.
  • Page 11 ELECTRICAL CONNECTIONS 220V OPERATION If 220V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from its power source. 2. The dust collector comes with four motor leads that are connected for 110V operation as shown in Fig.
  • Page 12 ELECTRICAL CONNECTIONS EXTENSION CORDS The use of any extension cord will cause some loss of power. Use the following table to LENGTH OF WIRE SIZES REQUIRED determine the minimum wire size (A.W.G- CONDUCTOR (AMERICAN WIRE GAUGE) American Wire Gauge) extension cord. Use only 110V LINES 3-wire extension cords which have 3-prong 0-25 FEET...
  • Page 13: Maintenance

    MAINTENANCE MOTOR Operational hints Excessive dust in the motor could cause excessive heat in the motor. During the first use and after cleaning, the filter bag may allow some dust to escape. This is Every effort should be made to prevent foreign normal and will stop after a short period of time.
  • Page 14: Troubleshooting

    TROUBLESHOOTING PROBLEM PROBABLE CAUSE REMEDY SUGGESTED Motor will not run. 1. Defective cord, plug, 1. Consult service. Any attempt to repair this motor may create a switch and/or motor. hazard unless repair is done by a qualified service technician. 2. Blown fuse. Repair service is available at your nearest service center.
  • Page 15 2. Fuses or circuit of fuses or circuit breakers do not have breakers. sufficient capacity. PARTS DIAGRAM & PARTS LISTS Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.
  • Page 16 In cooperation with our authorized serviced center, King Canada will either repair or replace the product if any part or parts covered under this warranty which examination proves to be defective in workmanship or material during the warranty period.
  • Page 17: Electrical Diagrams

    PROPERLY GROUNDED OUTLET CURRENT CARRYING PRONGS GROUNDING PRONG Figure 2 PARTS DIAGRAM & PARTS LISTS Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list.

Table of Contents