1. Manuals
  2. Brands
  3. Mutec Manuals
  4. Amplifier
  5. MC-7
  6. Operating manual

Mutec MC-7 Operating Manual

Word clock distribution amplifier & audio clock converter
Hide thumbs
Table of Contents

Advertisement

Quick Links

WORD CLOCK DISTRIBUTION AMPLIFIER &
AUDIO CLOCK CONVERTER

Advertisement

Table of Contents
loading

Related Manuals for Mutec MC-7

Summary of Contents for Mutec MC-7

  • Page 1 WORD CLOCK DISTRIBUTION AMPLIFIER & AUDIO CLOCK CONVERTER...

  • Page 3: Safety Instructions

    §1 Warranty MUTEC GmbH warrants the flawless performance of this product to the original buyer for a period of two (2) years from the date of purchase. If any failure occurs within the specified warranty period that is caused by defects in material and/or workmanship, MUTEC GmbH shall either repair or replace the product free of charge within 90 days.

  • Page 5: Table Of Contents

    General Function Description ....7 MC-7 Features ......7 MC-7 Applications .

  • Page 7: General Function Description

    This all makes MC-7 for sure an uni- years after purchasing the product. More- que and outstanding digital audio clock distributor and converter enabling...

  • Page 8: Peripheral Mutec Products

    > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Peripheral MUTEC Products...

  • Page 9: Control Elements And Terminals

    MULTIPLIERS panel. For adjusting these outputs see chapter OPERATING THE MC-7. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >...

  • Page 10: Rear Panel

    IEC 60958 stand- ard. Their numbering is aligned to the corresponding functional menu on the front panel. For adjusting these outputs see chapter OPERATING THE MC-7. 3 AES3/11 OUT 5 This AES/EBU output transmits a transformer-balanced electrical AES3 or AES11 signal.

  • Page 11: Installation

    Always be sure to connect the Word Clock output of the MC-7 the same, as this is the only way to to the corresponding input of the device you wish to synchronize.

  • Page 12: Wiring The Aes/Ebu And S/P-Dif Interfaces

    Special shielded cable material should be Glass fiber cables can transfer data reliably even over greater distances. used for transfer of higher clock rates. MUTEC offers optical cables of various lengths that have been specifically tested for the transmission of S/P-DIF and ADAT™...

  • Page 13: General Operation

    2 Switching the SELECT key activtes individual functions within one powering-up! function menu. We also recommend reading the CONTROL ELEMENTS AND TERMINALS chapter for information on how to connect MC-7! 2. SELECT 1. MENU selects individual selects individual functions within function menus.

  • Page 15: Operating The

    = x 256 of the reference signal‘s base clock rate MULTIPLIERS After these general decisions are made, your MC-7 is configured for optimal operation in your set-up! Due to the fact that the system monitors for useful function combinations, maloperation is not possible.

  • Page 16: Word Clock As Input Reference Including Options

    «. The Word Clock reference signal will be internally regenerated and distributed phase-aligned to all eight Word Clock outputs. Your MC-7 is able to lock to so- Simultaneously, the input signal will be converted into AES11 and S/P-DIF called »Super Clock« (SCLK) reference and output at the corresponding outputs.

  • Page 17: S/P-Dif Coaxial As Input Reference Including Options

    S/P-DIF coaxial as Input Reference including Options *) If you need to convert the AES3 format WCLK HOLD into S/P-DIF, please use the MUTEC MC-1 or MC-1.1. These converters are especially made AES3/11 REF PASS for AES3 to S/P-DIF, and vice versa, digital S/P-DIF co audio format conversion.

  • Page 18: S/P-Dif Optical As Input Reference Including Options

    CLK Multipliers as mentioned at page 19. *) If you need to convert the S/P-DIF format into AES3, please use the MUTEC MC-1 or MC-1.1. These converters are especially made for AES3 to S/P-DIF, and vice versa, digital audio format conversion.

  • Page 19: Multiplying Clock Rates

    Generatable Clock Rates rate multiplication factor to each pair of clock outputs. This is possible in any state of operation of your MC-7. The numbering of the multipliers is For a better understanding of the efficiency aligned to the output numbers. Select the prefered output with the MENU of the MC-7‘s clock multiplier, please refer...

  • Page 20: Status

    4: S/PDIF outputs run at 176.4kHz or 192.0kHz STATUS This area displays different system conditions of your MC-7. There is no access for changing settings. »LOCK« This blue LED lights when the internal PLL circuit has detected the incoming clock reference signal as valid.

  • Page 21: Appendix

    B E D I E N E L E M E N T E B E D I E N E L E M E N T E B E D I E N E L E M E N T E >...

  • Page 22: Switching-Off The Termination Of The Word Clock Input

    = Termination When moving the jumper from position 2 to position 1, the input termi- nation will be switched-off. Therefore, the MC-7 must be connected in a chain, in which a device with terminated input follows. Otherwise you need to use a BNC-T piece in combination with a 75 Ω BNC resistor for terminat- ing the MC-7’s input.

  • Page 23: Generatable Clock Rates, Example: 44.1Khz

    \\\\\\\\\\\\ AP P E N D I X AP P E N D I X AP P E N D I X > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Generatable Clock Rates, Example: 44.1kHz as Input Clock Rate for all mentioned Input Signals WORD CLOCK SIGNAL AS INPUT REFERENCE Outputs...
  • Page 24 \\\\\\\\\\\\\\\\\\ A N H A N G A N H A N G A N H A N G > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > AES11 BLANK FRAME SIGNAL AS INPUT REFERENCE + HOLD FUNCTION Outputs Multiply x 1...
  • Page 25 \\\\\\\\\\\\\\\\\\ A N H A N G A N H A N G A N H A N G > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > S/P-DIF OPTICAL DIGITAL AUDIO SIGNAL AS INPUT REFERENCE + HOLD FUNCTION Outputs Multiply x 1...

  • Page 26: Technical Data

    \\\\\\\\\\\\\\\\\\ A N H A N G A N H A N G A N H A N G > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Technical Data WORD CLOCK INPUT (WCLK) 1 x BNC, 200 mV-7 V, unbalanced, input impedance 75 Ω...
  • Page 28 > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > WWW.MUTEC-NET.DE FON 0049-(0)30-746880-0 ALL SOFTWARE AND HARDWARE PRODUCT NAMES ARE REGISTERED TRADEMARKS OF THEIR RESPECTIVE OWNERS. FAX 0049-(0)30-746880-99 WE RESERVE THE RIGHT TO CHANGE TECHNICAL DETAILS WITHOUT PRIOR NOTICE. © MUTEC GmbH 2002 • 7045-014...

Table of Contents