REGULATORY STATEMENTS Part15, Class A This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: This device may not cause harmful interface, and This device must accept any interface received, including interface that may cause undesired operation.
FCC Part 68 Registration This equipment complies with Part 68 of the FCC Rules. On the button of this equipment is label that contains, among other information, the FCC registration Number and Ringer equipment Number (REN) for the equipment. If requested, this information must be given to the Telephone Company.
REGULATORY STATEMENTS...1 Part15, Class A ...1 FCC Part 68 Registration ...2 Introduction...1 HE MANAGEABLE ...1 EATURES ...2 ACKAGE ONTENTS ...2 PECIFICATIONS Standards ...2 Interface ...2 Buffer Memory/MAC Address Table ...2 Certifications...2 Rich LED indicators...2 ARTS AMES AND UNCTIONS Front Panel ...3 Rear Panel ...4 Hardware Installation...5 ESKTOP...
Page 5
Using Daisy-chain Topology...9 How to Manage the Switch...10 ETUP TILITY ANAGEMENT Find ...13 Configure ...15 a. Ports (configures each HomePNA port status) ...15 b. Device (manages the HomePNA Switch) ...18 c. Configure (configures the parameters for each HomePNA port)...20 d. Statistics (displays the real-time status for each HomePNA port) ...21 Firmware Upgrade ...21 OCAL ONSOLE...
Page 6
power P L...40 threshold P L...41 pname P NAME...42 name [newname]...42 private [community]...42 vlist...43 vset GP ...44 vclr GP ...45 vrst ...46 voff ...47 SNMP M ...48 ANAGEMENT...
INTRODUCTION The manageable 14-port HomePNA Switch The manageable 14-port HomePNA Switch is a device utilizing the existing telephone wiring within a building to deliver data and does not interrupt regular voice services. Data and voice run simultaneously on the same pair of wire without any rewiring. It is suitable for hotel/motel, multi-tenant apartment, multi-tenant commercial, multi-tenant student dorm, campus and local loop.
Package Contents Open the box and carefully unpack the switch. You should have all the items on the following checklist: Manageable 14-port HomePNA Switch One power cord Four rubber feet Two mounting brackets and screws User’s manual Setup diskette Console cable If any items are missing or damaged, contact the retailer where you purchased the switch for assistance.
Parts Names and Functions Front Panel The front panel of the switch, displayed below, has fourteen 1Mbps switching ports supported. System Power LEDs Warning HomePNA LINK/ACT Port LEDs (Uplink) 100 LED LINK/ACT Blinks when receiving data. Ethernet Port LEDs (Downlink) 100 LED LINK/ACT Blinks when receiving data.
a RS232 Serial Port Connects to the serial port on your PC with the RS- 232 cable. b HomePNA Ports Connects to other HomePNA devices. Uplink 10/100 Fast Ethernet port with MDI/MDIX auto crossover capability. Management for the HomePNA switch through this (Management) Port port.
HARDWARE INSTALLATION The switch can be placed directly on your desktop, or mounted in a rack. Desktop Installation Follow these steps to install the switch on a desktop: 1. Place the four rubber feet at the corners of the switch. 2.
MDF/IDF Connection There are two ways to connect the switch to MDF/IDF panel. Method A: Cut in the existing phone line, connecting the PBX/PSTN ends to the switch LINE ports and the PCs to the PNA ports. Method B Keep the existing phone line, pulling another connection line from the MDF/IDF and connect it to the PNA ports.
EXPANDING TO MORE HOMEPNA PORTS To expand the home networking applications, you could: Uplinking to a Multi-ports Ethernet Switch Use an UTP CAT5 cable to connect the switch’s Uplink port to the Uplink of another Switching-Hub, for example an 8-ports switch, as illustrated below. Check the Link LED on the 8 port switch to verify if the switch and Ethernet switch are well connected.
HOW TO MANAGE THE SWITCH You can configure this Manageable 14-port HomePNA Switch through one of the following methods: 1. Setup Utility that comes with the package via an Ethernet connection. 2. Local Console management in terminal emulation program via a RS-232 cable connection.
Setup Utility Management Run the switch setup utility provided. Go to Start Run. Browse to select the setup utility and click OK. When the setup utility installation is complete, go to Start Programs HomePNA HomePNA Switch Management Utility. - 12 -...
Find When the opening screen appears, click Find to search for all the switches in the local network. Local Switch Click OK when the Find Switches window pops up. being found in the local network. Remote Switch To configure the switch outside the local network, you may enter the IP address of the switch and click OK.
Page 20
Remotely Configuration with IP sharing device 1. Click the Behind Firewall and check the box. 2. Enter the public IP address. 3. Click OK. Note: With this function provided, you can manage multiple switches without knowing their IP addresses. However, it is only applicable to our company’s associated device, like CA2000 or CAS2040, NAT Routers are not applicable.
Configure Select the switch that you want to manage from the switch list and press the Configure button to change the default settings. The Configure dialog box is categorized into four tabs. a. Ports (configures each HomePNA port status) - 15 -...
Page 22
Port Status Displays the Enable/Disable status for each HomePNA port. When the port button lights green, the port is enabled. When the port button lights red, the port is disabled. The default settings for all ports are Enabled. Click the port button to toggle between Enable/Disable status of each port.
Page 23
Displays the ports included in the VLAN Group you currently create. If you want to delete the port you previously added in the VLAN Group, you can click ▼ to remove them. Not In Group Displays the ports not included in the VLAN Group you currently create. You can highlight the ports in the list, click ▲...
Page 24
b. Device (manages the HomePNA Switch) Device Name Specifies the full name of the switch. The default device name for this switch is untitled. It is changeable. IP Address Specifies the unique IP address of your LAN. Default: 192.168.168.168. It is changeable.
Page 25
Adapter Address Displays the hardware address of the switch. Read only. Change Administrator’s Password Enter the user’s password in this field. Passwords are case sensitive. Please record the passport and keep it in safety. The default values have no password for the switch. administrator’s password and click apply all and reboot switch, you will jump back to the initial screen.
c. Configure (configures the parameters for each HomePNA port) Label Displays the name of each port. It is changeable. Power The default power level is 5. It is adjustable. For the best transmitting quality, you can move the arrow up or down to select the optimal level. Threshold The default threshold level is 4.
d. Statistics (displays the real-time status for each HomePNA port) Uplink Displays packets that the upper Fast Ethernet (Uplink) port counts from other cascade switches. Management Displays the real-time data transmitting status for the HomePNA Switch. Firmware Upgrade Follow the steps below to upload new firmware: Download the latest firmware from your distributor and save it to the hard drive of your PC or the floppy disk drive.
Page 28
Highlight the HomePNA switch and select the Upgrade button. When the Upgrade window opens, there are two options provided for your choice. Default File Replace the older firmware with the latest one in the default location (the default path followed by the file name is C:\FIRMWARE.BIN.) Specify File Replace the older firmware with the latest one in the specified location.
Page 29
When the firmware transfer is complete, you will see the Programming…Done message displayed on the screen. Click finish. - 23 -...
Local Console Management Local Console Management is done through the RS-232 Console port. Managing the switch in this mode requires a direct connection between a PC and the switch. This type of management is very useful when the network is not working and the switch cannot be reached by any other means.
Page 31
Name the new connection and select an icon for this session. In the Connect To dialog box, select the COM port that you used to connect to this switch. When the following dialog box appears, set the Bits per second rate as 38400, and Flow control at None.
Page 32
Once the connection is successfully made via HyperTerminal, press Enter to enter the configuration mode. The screen prompts you for the following command. command> Type help for a list of all commands. 10. Refer to the Telnet command for detailed description of each command. - 26 -...
Web Management Web Management provides you an easy access to set up your switch. Open the web browser, enter the IP address to the Switch (default: 192.168.168.168), and click “Go” to run the Web Management. In the home page, the left navigation pane where bookmarks are provided links you to the representative items to set up appropriate parameters.
Page 34
SAVE Click to save settings. RESET Click to go back to the saving screen. No VLANs Click to disable VLAN. Normal VLANs Click to return to the default value. - 28 -...
Device Setting Device Name Specifies the full name of the switch. Default: untitled. It is changeable. IP Address Specifies the unique IP address of your LAN. Default: 192.168.168.168. It is changeable. Subnet Mask Specifies the Subnet Mask. Default: 255.255.255.0. It is changeable. Gateway Specifies the Gateway.
Page 36
Specifies the hardware address of the switch. Read only. Change Password Enter the user’s password in this field. Passwords are case sensitive. Please record the passport and keep it in safety. The default values have no password for the switch. Once you setup the administrator’s password, every time you want to manage or configure the switch, the following screen may pop up and ask you to enter your password.
Ports Setting Label (Port Name) Displays the name of each port. It is changeable. Power The default power level is 5. It is adjustable. For the best transmitting quality, you can move the arrow up or down to select the optimal level. Threshold The default threshold level is 4.
View Stats (statistic) Label Displays the name of each port. It is changeable in Device Setting page. Port Displays the port number of each port. Displays the real-time data receiving byte counts for each HomePNA port. Displays the real-time data transmitting byte counts for each HomePNA port. Link Displays that which ports connect to the NIC.
Telnet Management Telnet is done over the network. You can manage the switch via Telnet. First you have to assign a unique IP address to the switch, then you can use the Telnet Management method. Follow these steps to manage the Switch Assign an IP address to the switch Run Telnet (e.g., telnet 192.168.168.168 , which is the factory default values for the HomePNA Switch)
Passwd List Uptime enable P disable P Quit Reboot power P L threshold P L pname P NAME name [newname] private [community] vlist vset G P vclr G P vrst voff P = port (1..14), L = level (0..10) show Displays the current configuration of the switch about the IP Address, Subnet Mask and Gateway.
Page 41
passwd No password is required for the first time login. Password can be set up to six characters long. Password is case sensitive. Example: command>passwd Please type old password : type new password (0 to 6 characters) : re-type new password (0 to 6 characters) : Password has been changed.
Page 42
Gateway : [192.168.1.254] Save and reboot ?(Yes/No) : [No] list Displays the status of each port. Example: command>list Port Enable Power Threshold RxCounter TxCounter Link label ==== ====== ===== ========= ========= ========= ==== ===== 6128 - 36 - 6128 management 6029 port 1 6029...
Page 43
uptime Displays how much time the switch has been running. Example: command>uptime System Name:Untitled System Uptime:90 seconds. enable # Each port can be set to enabled or disabled. You can only log in ports which are enabled, and make changes on them. After performing this command, there will be a listing of ports displayed on the screen.
Page 44
disable # Each port can be set to enabled or disabled. Disabled port cannot log in and no changes can be made. After performing this command, there will be a listing of ports displayed on the screen. Example: command>disable 2 Port Enable Power Threshold RxCounter TxCounter Link label ==== ====== ===== ========= ========= ========= ==== ===== 10333...
Page 45
quit This command allows you to exit the login prompt. Example: command>quit Bye ! reboot This command allows you to restart the switch, which simulates the action of powering the switch off and then back on. Example: command>reboot Disconnect & Reboot the switch ... 10333 - 39 - 10170...
Page 46
power P L This command allows you to adjust the transmitting level for each HomePNA port. * P: HomePNA Port # (1-14) * L: Level (1-10) Example: command>power 5 2 Port Enable Power Threshold RxCounter TxCounter Link label ==== ====== ===== ========= ========= ========= ==== ===== 10333 - 40 - 10332...
threshold P L This command allows you to adjust the receiving level for each HomePNA port. * P: HomePNA Port # (1-14) * L: Level (1-10) Example: command>threshold 5 2 Port Enable Power Threshold RxCounter TxCounter Link label ==== ====== ===== ========= ========= ========= ==== ===== 10333 - 41 - 10332...
Page 48
pname P NAME This command allows you to change name for each HomePNA ports. Example: command>pname 5 Home5 name [newname] The command allows you to set or display the system’s name. Example: command>name HSM1402 Setting Name to hsm1402 (Sets the switch’s name) command>name Switch Name:hsm1402 online for :1104 seconds.
Example: command>private public SNMP private community string set to public vlist This command allows you to view the virtual LAN Group status for each port. Example: Command>vlist Port Port #: 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 N P Group 0: V Group 1: Group 2:...
vset GP This command allows you to create new VLAN Groups. The following example shows you how to add Port 3, Port 5 in the VLAN Group 1. G: VLAN Group # (1-14) P: HomePNA Port # (1-14) Example: command>vset 1 3 5 Port Port #: 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 N P...
vclr GP This command allows you to delete VLAN settings. The following example shows you how to remove Port 3, Port 5 from VLAN Group 1. Example: command>vclr 3 5 1 Port Port #: 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 N P Group 0: V Group 1: Group 2:...
vrst This command allows you to reset VLAN Groups. Example: command>vrst Resetting VLAN Port Port #: 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 N P Group 0: V Group 1: Group 2: Group 4: Group 4: Group 5:...
voff This command allows you to disable VLAN Groups. Example: command>voff Port Port #: 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 N P Group 0: V V V V V V V V V V V V V V V Group 1: V V V V V V V V V V V V V V V Group 2: V V V V V V V V V V V V V V V Group 4: V V V V V V V V V V V V V V V...
SNMP Management The Manageable 14-port HomePNA Switch supports SNMP through SNMP applications, like SNMPc or Hewlett Packard OpenView. documentation for instructions on installing and using the SNMP applications that you choose. SNMP: Simple Network Management Protocol As networked installations become larger and more complex, the cost of network management rises.