Page 1
Introduction The DIP1000 system is a perfect solution to extend HDMI, USB, and optional IR/RS‐232/Remote‐Power‐On‐Off over IP networks. It includes the main units of DIP1000 DIP1000T transmitter and DIP1000R Receiver, as well as the below mentioned optional accessories. The DIP1000T transmitter connects with a PC or any other device with via HDMI source. The DIP1000R receiver connects to HDMI display, speaker, microphone, USB devices (Keyboard/Mouse/Storage/…) and RS232 devices. It is based on the standard Ethernet IP network. Gigabit or Fiber LAN switches can be used for HDMI with USB inter‐connection or multi‐casting. Optional Accessories: Over 3.5m mini‐stereo to DB9 Female RS232 control cable 3.5m mini‐stereo to DB9 Male RS232 control cable IP LAN 3.5m mini‐stereo to 2‐pins Remote Power on/off cable IR blaster cable (Multi‐cast Version) Installation and User’s Manual For Sales and Service please contact ICP Global Pty Ltd Phone ‐ 02 9314 2092 Fax ‐ 02 9344 9537 Suite 603, Level 5, 152 Bunnerong Road PAGEOOD NSW 2035 Date: October 4, 2011...
Panel View On/Off (optional) DIP1000T Transmitter 4 bit DIP switch for 16 ID settings. To enable Transmitter/Receiver as a pair 6 Link ID or group, the transmitter and receiver must be set with the same Link ID. 7 Gigabit Ethernet For connecting directly to DIP1000R or via a Gigabyte Switch 8 RS‐232 Control Provide Serial‐over‐IP function. (optional) 9 DC 5V In System power input (DC 5V 2A) Connects this USB‐B to PC: 1. USB audio device. (USB audio device will be detected when it is 10 USB‐to‐PC attached to PC in Windows OS) 2. Virtual 4‐port USB Hub for remote USB devices. Connects to HDMI Source. For DVI source, you may need a HDMI‐to‐DVI 11 HDMI IN adapter cable. No. Component Description 12 IR Blaster Connects to external IR LED. (optional) 1 HDMI Loop‐out HDMI Loop‐out for Local Monitor. Press button for 1 Switch video to Remote or Loop‐out monitor. Panel View second Press button for > 3 Output video to both Remote and Loop‐out DIP1000R Receiver 2 (Button 1) seconds monitors. Press and Hold Power ON Resets unit to the Factory default setting. until Green and Red LED’s ...
Page 3
Stereo Audio output for the USB PnP audio device. (Set the OS 13 Line OUT default audio to the USB PnP audio device that is created by the No. Component Description DIP1000T) Green Blinking/Red Off: System is starting up. 14 Gigabit Ethernet For connecting directly to DIP1000T or via a Gigabyte Switch 1 Green LED (Power/Link) Green On/Red Blinking: Linking or waiting HDMI input. 2 Red LED (System status) Green On/Red On: Connection established. 4 bit DIP switch for 16 ID settings. To enable Transmitter/Receiver as 3 Link ID a pair or group, the transmitter and receiver must be set with the same Link ID. 4 USB Host For remote USB devices, such as USB KB/Mouse, storage, audio, … 5 IR Rx (optional) Remote Universal IR receiver. 6 Remote Power On/Off Button for Remote PC Power On/Off function. (optional) Press button for 1 Switch to Video or Graphic mode second Anti‐Dither Mode. Setting to “Anti‐Dither Press button for > 3 Mode” to achieve better video quality for seconds 7 Mode button some ATI graphic cards. Press and Hold at Establishes EDID as the system EDID Power ON until Green (update DIP1000T EDID) LED blinking Press button for 1 ...
2. To Use the DIP1000T Loop‐out monitor EDID: Press and Hold the Button to Installation Power ON until the Green LED starts blinking. 1. Ensure that the Link‐ID of both the DIP1000T and DIP1000R have the same 3. To update the DIP1000R EDID: Press and Hold the Mode button to Power ON settings. until Green LED is blinking. 2. Attach the HDMI display to the DIP1000R HDMI‐Out port. 4. To Reset the DIP1000R to the Factory default setting: Press and Hold the Link 3. Power on the DIP1000R. An “AVExtender” logo will be displayed. If this does not button to Power ON until Green and Red LED’s are blinking. appear an error has occurred with either the DIP1000R, HDMI cable or the Remote Power On/Off (optional) display. 4. You can connect multiple DIP1000R’s and multiple DIP1000T units to your Gigabit This function is designed for remote Power on/off control of your PC through the Ethernet switch. Alternatively use a CAT6 UTP cable (straight, EIA 568B) to DIP1000R [Remote Power On/Off] push button. directly connect a DIP1000T with a DIP1000R as a pair. 5. Attach the HDMI source (PC or Blue‐Ray) to the DIP1000T HDMI‐In port and then power On the DIP1000T. 6. The first DIP1000R that is detected by the DIP1000T will gain the USB access right. 7. If you are using your PC as your HDMI source, you will see your HDMI display EDID information on the PC graphic card control panel. If not, then something is wrong either with the DIP1000T or HDMI cable. 8. Output HDMI (with audio) from HDMI source and check if they are correctly displayed on your HDMI display. USB over IP installation: ...
1. Connect the 3.5mm mini‐stereo plug of the supplied RS‐232 cable to the [RS‐232] socket at the rear panel of the DIP1000T Transmitter, and then connect the DB9 Female connector of the supplied RS‐232 cable to the COM port of your PC. 2. Connect the 3.5mm mini‐stereo plug of the supplied RS‐232 cable to the [RS‐232] socket at the rear panel of the DIP1000R Receiver, and then connect the DB9 Male connector of the supplied RS‐232 cable to the RS‐232 device. RS232 Pin Assignments Signal ‐NC‐ TxD RxD ‐NC‐ ‐NC‐ ‐NC‐ ‐NC‐ ‐NC‐ ‐NC‐ DIP1000R 5 3 2 7 8 4 6 1 9 DIP1000T 5 2 3 8 7 6 4 1 9 Infrared Control (optional) This function is designed to transmit IR signal from the DIP1000R to the AV sources. ...