Table of Contents
Advertisement
electrical circuit connections as arranged in the 110-120 volt and.~.125wl.30 .... ¯
volt Model T9 Toasters.
"
'
' " '
Note: The front of th~ Toaster is the side with the Signal light ; which
places the. movable handle ~x~d thermostat adjustment knob on the right side -....
and the fixed handle and "pop-up" control kno.b..on the left side when the
user faces the front of the Toaster° USE ON ALTERNATING CURRENT ONLY.
HOW TO SERVICE MODEL ~T9 SUNBEAM AUTOMATIC TOASTER
Plug toaster co~d into electric power circuit of same' voltage as that marked
on name plate at bottom of toaster. The electric power circuih must have
sufficient capacity fdr ~upplying the Toaster with.the wattage it require~
list attached to this bulletin)..is lowered the switch closes, all elements
..
will heat to a cherry red .color, ~nd the signal light wil.! glow. ' '
¯
The main thermostat blade (key number 47) is heated by the 'thermostat heater
element (5), the heat is reflected to the thermostat by the reflector (3)
and the amount of ~heat reaching the thermostat blade is 96gulated by moving
this reflector through the cam (13) 'turned by t~e thermostat adjustment"
knob (24). The temperature at which the thermostat snaps off is regulate~
by the tension of the coiled spring (48) which can be adjusted byturning.
the nut (49A). The thermostat blade will snap with a '~61ick" against the
flat s.urface of its supporting casting. But before it reaches this surface
the thermostat blade hits the end of lever (33) which opens the switch and
if the 'control (2~D) is set to "pop-up" the toast ra~k will move up, coming
to a slow stop. The cushioning cylinder (56A) dampens the action of the
"pop-up" spring. If the control k~ob (24D) is inthe position marked "Keeps
Toast Warm", the movable handle (15) must be raised by hand to remove the
toast. The thermostat blade (~7) cools rapidly and snaps back into its orig-
inal position with a second "click" a few seconds after the flrst~ thus re-
setting the thermostat, The ~ext toast must not be started until after this
second click. The auxili~-~ t-~e ~rmos-~at ~ compensates for the temperature
rise in the metal parts of the toaster~ Without the auxiliary thermostat,
the toast would tend to become lighter as successive slices, were made.
2. Taking Toaster A_~_~.
"
2-A. To remove bottom cover and thermostat bracket a~sembly (12). Use Tool No. 1
(see list of tools at the end of this bulletin) to remove the four Gulmite
screws(6OA) near the edges of the thermostat bracket and the..crumb tray and ¯
bracket (12) may be removed from the plastic base (16). 'Th~ thermostat b~acket
should be carefully lifted out, sliding the thermostat blade ~(47) over .the end
of the switch locking lever (33). Remoi~lng the thermostat bracket (12~ pe~ts
inspection of the heat adjustment cam (13), the reflector assembly (3) and the
thermostat heater element (5)°
: ~
' ¯ ~ ¯
2-A1.The thermostat blade (47) may be removed from the assembly by first loosening
the spanner nut (49A) for tension on adjusting spring (~). Then ~ take off
shield (64) from the auxilia~ thermostat (46), and remove shoulder screw (44)
and its nut (~AA), This will relieve pressure of set screw (55) on the main
thermostat blade (47) which may now be lifted out from under the .thermostat
stop (43).
'
~"
Hide quick links:
Advertisement
Table of Contents
