Summary of Contents for Hyper Vision DVR-800
- Page 1 Hyper Vision DVR-800 & 1600 8 & 16 Channels DVR Card Kit Installation Guide Date: Apr. 17. 2003...
-
Page 2: Table Of Contents
LIST DVR-800 & 1600 DVR SYSTEM REQUIREMENT..............3 DVR-800 & 1600 CARD KIT PACKAGE CONTENTS ............4 INSTALL THE CAPTURE CARDS ...................5 INSTALL THE FLASH MODULE & HARD DISK ..............6 4-1 I ......................6 NSTALL THE LASH ODULE 4-2 I ........................7 NSTALL ARD DISK INSTALL OTHER PARTS ......................8... -
Page 3: Dvr-800 & 1600 Dvr System Requirement
1. DVR-800 & 1600 DVR System Requirement Hyper Vision 8CH & 16CH DVR card kit needs to specify the combination of “motherboard chipset ”, “VGA chip”, and “network interface chip”. Hyper Vision DVR card kit specifies: Motherboard Chipset Intel 845E, SiS645DX, SiS648, Intel 845PE... -
Page 4: Dvr-800 & 1600 Card Kit Package Contents
2. DVR-800 & 1600 Card Kit Package Contents DVR-800 & 1600 card kit includes, 1. Four capture cards (Fig.2-1). 2. One system module and one power cable for this module (Fig2-2) 3. One special cable for connecting the system module and internal CD/RW. If you use the external CD/RW (USB interface), you won’t need this cable (Fig2-3). -
Page 5: Install The Capture Cards
AGP slot for display card Network card here Fig 3-1 DVR-800 & 1600 capture cards installed on GA-8IEX Remark: The example above is the installation procedure on GA-8IEX motherboard. For the other motherboard with Intel 845E/SiS 645DX/SiS648 chipset, the installation procedure is similar to the above procedures. -
Page 6: Install The Flash Module & Hard Disk
“Master”, then connect the D-type power line to power supply as the figure below. If you would like to install the internal CD/RW burner also (DVR-800 & 1600 supports the internal CD/RW and USB external CD/RW both), please use the special... -
Page 7: Install Hard Disk
4-2 Install Hard disk DVR-800 & 1600 could support 2 Hard Disks. If you install one hard disk only, please set it as Secondary IDE “Master”. If you install the 2nd hard disk, please set it as Secondary IDE “Slave”. -
Page 8: Install Other Parts
5. Install Other Parts 5-1 CPU GA-8IEX has a Socket 478 for CPU. For Hyper Vision, the system recording frame rate is depended on the CPU that system uses. If it uses the Intel P4-2.4G, the system recording frame rate is around 100fps(Frame per Second). -
Page 9: Configure Bios Parameters
6. Configure BIOS Parameters Due to heavy traffic between IO devices and motherboard, the optimum BIOS configuration is necessary for Digital Video Recorder system to have stable operation. When you finish assembling Capture Cards, Flash Module, and Hard Disk, please connect the keyboard and mouse before turning on power for setting BIOS. After power on, you will see a flash screen of display logo followed by a POST (power on self-test) screen with sentence “Hit DEL if you want to run SETUP”. -
Page 10: For Gigabyte Ga-8Iex
6-1. for Gigabyte GA-8IEX Please select [Load Optimize Defaults] in the main menu to load optimum setting, then please refer to the setting listed in the next. [Standard CMOS features] IDE Primary Master [PQI IDE Secured Disk] IDE Primary Slave [None] IDE Secondary Master [your hard disk]... -
Page 11: Power Management Setup
Onboard Parallel Port [Disabled] Game Port Address [Disabled] Midi Port Address [Disabled] CIR Port Address [Disabled] [Power Management Setup] ACPI Suspend Type [S1(POS)] Soft-off by PWR-BTTN [Instant-Off] PME Event Wake Up [Enabled] ModemRingOn/WakeOnLan [Disabled] Resume by Alarm [Disabled ] Power On By Mouse [Disabled] Power On By Keyboard [Disabled]... -
Page 12: For Gigabyte Ga-8Sg667
6-2.for Gigabyte GA-8SG667 Please select [Load Optimize Defaults] in the main menu to load optimum setting, then please refer to the setting listed in the next. [Standard CMOS features] IDE Primary Master [PQI IDE Secured Disk] IDE Primary Slave [None] IDE Secondary Master [your hard disk] IDE Secondary Slave... - Page 13 Midi Port Address [Disabled] [Power Management Setup] ACPI Suspend Type [S1(POS)] Soft-off by PWR-BTTN [Off] System After AC Back [Laststate] IRQ [3-7,9-15]NMI [Enabled] ModemRingOn/WakeOnLan [Enabled] PME Event Wake Up [Enabled] Power On By Keyboard [Disabled] Power On By Mouse [Disabled] Resume by Alarm [Disabled ] Power LED in S1 State...
-
Page 14: For Asus P4S533-E
6-3.for ASUS P4S533-E Please select [Load Optimize Defaults] in the main menu to load optimum setting, then please refer to the setting listed in the next. [Main] Legacy Diskette A [1.44M, 3.5“] Floppy 3 Mode Support [Disabled] Primary Master [PQI IDE Secured Disk] Type [Auto] Cylinders... - Page 15 BIOS Update [Disabled] PS/2 Mouse function Control [Enabled] USB Legacy Support [Auto] OS/2 Onboard Memory >64M [Disabled] Chip Configuration SDRAM Configuration [By SPD] SDRAM CAS Latency [2.5T] SDRAM RAS to CAS Delay [3T] SDRAM RAS Precharge Time [3T] SDRAM RAS Active Time [7T] SDRAM Commend Lead-off Time [Auto]...
- Page 16 IRQ 3 Reserved [No/ICU] IRQ 4 Reserved [No/ICU] IRQ 5 Reserved [No/ICU] IRQ 7 Reserved [No/ICU] IRQ 9 Reserved [No/ICU] IRQ 10 Reserved [No/ICU] IRQ 11 Reserved [No/ICU] IRQ 12 Reserved [No/ICU] IRQ 14 Reserved [No/ICU] IRQ 15 Reserved [No/ICU] [Power] Power Management [User Defined]...
-
Page 17: For Asus P4Pe
Boot Up Floppy Seek [Disabled] Full Screen Logo [Disabled] Interrupt Mode [APIC] 6-4.for ASUS P4PE Please select [Load Optimize Defaults] in the main menu to load optimum setting, then please refer to the setting listed in the next. [Main] Legacy Diskette A [1.44M, 3.5“] Floppy 3 Mode Support [Disabled]... - Page 18 Keyboard Auto-Repeat Rate [ 12/Sec ] Keyboard Auto-Repeat Delay [1/4 Sec ] Language [English(US)] Supervisor Password [Disabled] User Password [Disabled] Halt on [All but Disk/Keyboard] [Advanced ] CPU Speed [2400MHz] CPU Frequency Multiple [18x] CPU External Frequency(MHz) [133] Memory Frequency [Auto] AGP/PCI Frequency Setting [Auto]...
- Page 19 Memory Hole At 15M-16M [Disabled] Delay Transaction [Enabled] Onboard PCI IDE Enable [Both] USB 2.0 HS Reference Voltage [Medium] I/O Device Configuration Floppy Disk Access Control [R/W] Onboard Serial Port 1 [3F8H/IRQ4] Onboard Serial Port 2 [2F8H/IRQ3] UART2 Use As [COM Port] Onboard Parallel Port [Disabled]...
- Page 20 IRQ 14 Reserved [No/ICU] IRQ 15 Reserved [No/ICU] [Power] Power Management [User Defined] Video Off Option [Suspend-> Off] Video Off Method [DPMS Off] HDD Power Down [Disabled] ACPI Suspend to RAM [Disabled] Suspend Mode [Disabled] PWR Button < 4 Secs [Soft Off] Power Up Control AC Power Loss Restart...
-
Page 21: For Gigabyte Ga-8Pe667 Pro
6-5.for Gigabyte GA-8PE667 Pro Please select [Load Optimize Defaults] in the main menu to load optimum setting, then please refer to the setting listed in the next. [Standard CMOS features] IDE Primary Master [PQI IDE Secured Disk] IDE Primary Slave [None] IDE Secondary Master [your hard disk]... - Page 22 Onboard Serial Port [2F8/IRQ3](Enable for PTZ) Onboard Parallel Port [Disabled] Game Port Address [Disabled] Midi Port Address [Disabled] CIR Port Address [Disabled] [Power Management Setup] ACPI Suspend Type [S1(POS)] Power LED in S1 State [Blinking] Soft-off by PWR-BTTN [Off] PME Event Wake Up [Enabled] ModemRingOn/WakeOnLan [Enabled]...
- Page 23 AGP OverVoltage Control [Normal] CPU Voltage Control [Normal]...
-
Page 24: Boot And Test
When first booting, system will enter the “Disk Management” option. Please refer to the Section 4 of the Hyper Vision 16 user manual for the related procedures for the hard disk management. After finishing the disk management, the system will reboot and show the main monitoring screen as follows. -
Page 25: Question And Answer
8. Question and Answer 8-1 System requests to format Hard disk again after formatting hard disk. Ans: Hard disk failure. Ans: IDE flat cable failure or with wrong connection. 8-2 System reboots continuously. Ans: There might be the serious bad track on the hard disk. Please change a new one Ans: There are too many bad bits on the DRAM module.