Carrier TSTATCCREC01 Installation Instructions Manual
Hide thumbs
Also See for TSTATCCREC01:
- Product data (8 pages) ,
- Installation instructions manual (13 pages)
Advertisement
Advertisement
Related Manuals for Carrier TSTATCCREC01
Summary of Contents for Carrier TSTATCCREC01
-
Page 1: Installation Instructions
Installation Instructions TSTATCCREC01 Wireless Reciever TSTATBBREC01 P474-1100REC NOTE: Read the entire instruction manual before starting the installation. HEAT COOL HEAT COOL & POWER HEAT PUMP MULTI-STAGE WIRELESS RECIEVER Catalog No. 13TS-TA36 Form: IM-TSTAT-10 Cancels: Printed in U.S.A. -
Page 2: Table Of Contents
Table Of Contents PREPARATION REMOVE OLD THERMOSTAT MOUNT WALL PLATE & WIRE CONNECTIONS & SWITCHES WIRING DIAGRAMS CALABRATION TROUBLESHOOTING CAUTION Follow Installation Instructions carefully. DISCONNECT POWER TO THE HEATER - AIR CONDITIONER BEFORE REMOVING THE OLD THERMOSTAT AND INSTALLING WARNING THE NEW THERMOSTAT. -
Page 3: Preparation
STEP #1 PREPARATION 12:00 Cool Fan Auto Proper installation of the receiver will be MODE accomplished by following these step by step instructions. If you are unsure about any of these steps, call a qualified technician for assistance. 12:00 Cool Fan Auto Assemble tools as shown below. -
Page 4: Remove Old Thermostat
STEP #2 REMOVE OLD THERMOSTAT 12:00 Cool Fan Auto Turn off the power to the Heating/Air MODE Conditioning system at the main fuse panel. Most residential systems have a separate breaker for disconnecting power to the furnace. 12:00 Cool Fan Auto Remove the cover of the old thermostat. -
Page 5: Mount Wall Plate & Wire
STEP #3 MOUNT WALL PLATE AND WIRE Mount the wall plate with the 2 screws supplied. 12:00 Cool Fan Auto Use the supplied wall anchors if mounting on MODE drywall. A 3/16" hole will have to be drilled for the wall anchors. If the terminal designations on your old 12:00 Cool... -
Page 6: Connections & Switches
Connections & Switches - Setting House Code Terminals for Antenna Connection to HVAC Switches Circuit Board Rear Housing ON Indicator Add all ON switches to arrive at HOUSE CODE number. All thermostats Example: communicating with this House Code 10, receiver must have the 2+8=10 same House Code #. - Page 7 Connections & Switches - Heat Pump Circuit Board Antenna Switches Heat Pump ON Indicator To configure the receiver for heat pump operation Slide HP switch to the ON position as shown. Reversing Valve polarity (O or B) can also be set. O / B O / B OFF = O, ON = B...
-
Page 8: Wiring Diagrams
Sample Wiring Diagrams 5 Wire, 1 Stage Cooling, 1 Stage Gas Heat Residential Gas or Electric Heat *, Electric Cool, split systems & package units Receiver 24 vac common fan relay compressor relay 1st stage heat circuit 24 vac return * If using electric heat this option must be selected on during advanced setup. - Page 9 Sample Wiring Diagrams 6 Wire, 2 Stage Cooling, 1 Stage Heat Residential 2 Stage Cooling, with Gas or Electric Heat* Receiver 24 vac common fan relay compressor relay 1st stage heat circuit 24 vac return 2nd stage compressor relay * If using electric heat, this option must be selected during advanced setup.
- Page 10 Sample Wiring Diagrams Commercial Gas or Electric Heat ***, 7 Wire, 2 Stage Cooling, 2 Stage Heat Electric Cool, split systems & package units including Commercial Heat Pumps ** Receiver 24 vac common fan relay compressor relay 1st stage heat circuit 24 vac return 2nd stage compressor relay 2nd stage heat circuit...
-
Page 11: Calabration
Sample Wiring Diagram Sample Wiring Diagram 6 Wire, 1 Stage Cooling, 2 Stage Heat, Heat Pump * Most residential split and package heat pumps with auxiliary heat Receiver 24 vac common fan relay compressor relay 1st stage heat circuit 24 vac return 2nd stage heat circuit * The heat pump option must be selected on during advanced setup. -
Page 12: Troubleshooting
TROUBLESHOOTING 12:00 Cool Fan Auto SYMPTOM: When using 4 wires (R, G, W, Y), MODE the air conditioning or heat equipment tries repeatedly to turn on, but cannot. At times the display dims or disappears. CAUSE: There is not enough power available to "power share". - Page 13 TROUBLESHOOTING 12:00 Cool Fan Auto SYMPTOM: When controlling a residential heat MODE pump, and asking for cooling, the heat comes on. CAUSE: Heat pump is not selected "on" in the Advanced Setup. REMEDY: Select heat pump on during Advanced Setup programming. Consult the Owner's Manual.