Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for SnapAV Dragonfly
- Page 1 I N STALL AT ION MA N UA L Motorized Tab Tension Projection Screen...
-
Page 2: Important Safety Precautions And Warnings
Before you unpack the projection screen, read the entire manual to become familiar with the steps involved for installation and operation. If you feel uncomfortable performing any of the steps required, stop and consult a qualified installation professional. Dragonfly is not responsible for any damage or injury that occurs from incorrect installation or operation. -
Page 3: Table Of Contents
8. Using the Screen 8.1. Automated Control 8.2. Manual Control 9. Cleaning the Projection Screen 10. Troubleshooting 11. Specifications 12. Dimensions and Weight 12.1. Screen and Housing 12.2. Mounting Brackets 13. Warranty 14. Contacting Technical Support Pg. 3 www.snapav.com Support: 866.838.5052... -
Page 4: Overview
DFM-TAB Installation Manual 2. Overview Thank you for purchasing a Dragonfly™ Motorized Projection Screen. These projection screens can be hidden away when not in use and are designed to be easy to operate and reliable. They feature several convenient mounting methods, can be controlled manually or automatically by a control system or projector, and are fully adjustable. -
Page 5: Pre-Installation
4.5. Control Method Dragonfly motorized screens can be controlled via manual wall switch, IR remote, 12 volt trigger, or RS232. Complete instructions for each method are described in the Control Setup section (Page 9). Decide on the method that will be used before installation begins to avoid any issues with control later. -
Page 6: Installation
Use a 7/32” masonry bit to drill a hole for each screw. • Insert the anchors into the holes until they are flush. • Do not install anchors into mortar joints. • Use 4 of the 8 included screws to mount each bracket as pictured. Pg. 6 © 2013 Dragonfly... -
Page 7: Hanging Mount
3. Hang one bracket from the suspension system at the desired height. 4. Using a level, attach the second bracket to the suspension system at the same height as the first bracket. Pg. 7 www.snapav.com Support: 866.838.5052... -
Page 8: Installing The Screen On The Brackets
If everything is working correctly, continue with the installation. For any issues see the Troubleshooting section on page 13. Control Connections Viewing Manual Power Area Button (Bottom View of Screen) Pg. 8 © 2013 Dragonfly... -
Page 9: Control Setup
Mount the IR receiver using the adhesive foam tape on the back. Note: The included external IR receiver is proprietary to Dragonfly projection screens. Other IR receivers will not work correctly. -
Page 10: Ext Ctrl Port Wiring Diagram
3. Terminate conductors in the Cat5e/6 to the desired pins of the RJ12 connector as shown in the diagram above. Insulate the ends of the unused RJ12 conductors to prevent short circuits. 4. Terminate the same conductors to the appropriate wires on the RS232 port or contact/relay connection of the control system processor. Pg. 10 © 2013 Dragonfly... -
Page 11: Screen Adjustments
Turn the adjustment knob on each side until both sides are even and flat. • To tighten the tabs, turn the adjustment knob CLOCKWISE. • To loosen the tabs, turn the adjustment knob COUNTERCLOCKWISE. Pg. 11 www.snapav.com Support: 866.838.5052... -
Page 12: Using The Screen
9. Cleaning the Projection Screen Dragonfly screens are designed to provide many years of trouble-free use. After the screen is installed and adjusted, no further maintenance is required for the operation of the screen, unless the viewing surface gets dirty. Follow these guidelines to clean any marks or residue from the viewing surface: •... -
Page 13: Troubleshooting
If you have trouble, check the installation while reviewing all instructions. Some of the most common issues and solutions are also listed below. If you continue to have trouble, please contact an authorized Dragonfly dealer, or Dragonfly support at Info@dragonflyscreens.com or (866)838-5052... -
Page 14: Dimensions And Weight
5.71 117.48 5.47 59.92 95.87 3.94 17.72 5.79 4.49 109.80 60.58 DFM-TAB-123-MW-1610 5.71 126.18 5.47 65.35 104.57 3.94 17.72 5.79 4.49 118.50 63.60 DFM-TAB-133-MW-1610 5.71 134.92 5.47 70.83 113.31 3.94 17.72 5.79 4.49 127.24 69.00 Pg. 14 © 2013 Dragonfly... -
Page 15: Mounting Brackets
This warranty shall not apply to products which have been abused, modified or disassembled. Products to be repaired under this warranty must be returned to SnapAV or a designated service center with prior notification and an assigned return authorization number (RA). - Page 16 © 2013 Dragonfly 131230-1200...
Need help?
Do you have a question about the Dragonfly and is the answer not in the manual?
Questions and answers