Features of the JX4000 Types of Installations System Requirements Kit Contents Tools Required M10II Front & Rear Panel Features Connections & Features of the Amplified Antenna The DC Power Injector/Lightning Protector Overall System Configuration Antenna System Connections Surveying the Antenna Site Preparing for System Installation Mounting &...
Rev. A Page 4 Clarion/Hyperlink Bridge Kit Installation Manual WARNINGS The manufacturer assumes no responsibility for damage caused by interference due to this equipment. Radio Frequency Interference Statement USA - Federal Communications Commission (FCC): This device complies with Part 15 of FCC Rules. Operation of this device is subject to the following two conditions: This device may not cause harmful interference.
The M10II offers true “Plug and Play” installation. No additional driver software is required for operation. That is, the M10II can be connected not only to a computer but also to a hub or to a router.
Central Node in a Multipoint Network or Mobile Network: This type of installation typically requires an Omni Directional Kit at the central node for 360 degree coverage. System Requirements The Clarion/HyperGain™ Amplified Extended Range Bridge Kit provides a Hyperlink Technologies, Inc.
Please read this manual in its entirety before beginning the installation. Kit Contents: Each Kit contains the following items: Clarion M10II Radio and DC Power Supply HyperAmp Remote Mounted Amplifier HyperGain Antenna (Omni, Yagi, or Grid) HyperGain DC Power Injector/Lightning Protector Signal Filter 50 ft.
Rev. A Page 8 Clarion/Hyperlink Bridge Kit Installation Manual M10II Front and Rear Panel Features Internal antenna (inside of the top cover) MAU port MAU LED TX LED External antenna port RX LED Power LED DC 6.2V port Power Switch...
Rev. A Page 9 Clarion/Hyperlink Bridge Kit Installation Manual Connections and Features of the Amplified Antenna Familiarize yourself with the connections and features of the Amplifier Unit: Mounting Flanges: Two sets of mounting holes are provided on the amplifier’s mounting flanges for either mast mounting using the included U-bolts, or bolted directly to a bracket or other structure.
Rev. A Page 10 Clarion/Hyperlink Bridge Kit Installation Manual The DC Power Injector/ Lightning Protector The DC Power Injector (also known as a "Bias-T") is an in-line device which couples DC power onto a coaxial cable, enabling the cable to carry both RF (radio frequency) signals and DC power.
Rev. A Page 11 Clarion/Hyperlink Bridge Kit Installation Manual Overall System Configuration The overall system configuration is shown below. Refer to this diagram while reading the section which follows, and during system installation. Transceiver JX-4000 Antenna AUI to 10BaseT Signal Filter...
Rev. A Page 12 Clarion/Hyperlink Bridge Kit Installation Manual ANTENNA SYSTEM CONNECTION Warning The M10II may only be operated using one of the approved antenna kits described herein. All antenna system components equipped with unique connectors. Although these connectors may look similar to standard types they are not compatible with them.
Rev. A Page 13 Clarion/Hyperlink Bridge Kit Installation Manual Preparing for System Installation Warning: These antennas are designed to be mounted in open areas such as rooftops or building exterior walls. They are designed to be installed at least 6 feet away from areas occupied by people. During system operation, always keep the antenna at least 1 foot away from your head.
Page 13
10. Attach the end of the 50 ft. antenna cable to the DC Power Injector. Attach the 4 foot adapter cable between the DC Power Injector and the M10II. 11. Attach a second ground wire to the ground lug on the DC Power Injector/Lightning Protector and to a good building ground.
Rev. A Page 15 Clarion/Hyperlink Bridge Kit Installation Manual Basic System Checks Using the system’s diagnostic LEDs, some basic system checks can now be performed. When the power is applied to the amplifier, the Power/Transmit indicator LED (found on the bottom corner of the amplifier) glows green. the Power Indicator LED on the DC Power Injector/ Lightning Protector will also illuminate green.
Rev. A Page 16 Clarion/Hyperlink Bridge Kit Installation Manual M10II LED Diagnostic Display During power-up, the front panel LEDs on the M10II provide some diagnostic information. Refer to the table below for LED diagnostic information. Label Color Description Green Indicates MAU signal (upload or download) is active.
+60 C Humidity: 0% ~ 1. Note 1 M10II has its own MAC address for configuration of operating parameters. M10II also memorizes single MAC address of attached Network Interface Card(s) for re-transmission protocol. Spread Spectrum p-persistent CSMA Hyperlink Technologies, Inc.
Rev. A Page 18 Clarion/Hyperlink Bridge Kit Installation Manual Clarion Quick Installation Manual A quick installation manual for Clarion Amplified and non-amplified systems. www.hyperlinktech.com Hyperlink Technologies, Inc.
Page 18
• (2) Antenna Mounting Hardware • Sealant Tape • Manual OS requirements: The Clarion radios are true transparent bridges so they will work with all Operating Systems, protocols, IEEE 802.3 and Ethernet II Tools: 7/16” open-end wrench or adjustable wrench...
Page 19
2. Connect the CAT 5 Patch cable from the transceiver to the computer network card. 3. Connect the Clarion antenna adapter cable to the EXT ANT on the back of the Clarion radio. 4. Connect the Clarion adapter cable to the lightning protector for non-amplified and into the DC Power Injector for amplified systems.
Page 20
Please follow the the steps below to power up the equipment. 1. Power on the Clarion radio first. The power button on the front of the radio is not operational. When the power cord is inserted into the radio it will power up. The following is the LED sequence that should appear after you power up the radio (self-test).
Page 21
Rev. A Page 22 Clarion/Hyperlink Bridge Kit Installation Manual 1201 Clint Moore Road Boca Raton, FL 33487 Technical Support and Sales Web Site: www.hyperlinktech.com For technical support support@hyperlinktech.com For Sales sales@hyperlinktech.com Phone: 561-995-2256 Fax: 561-995-2432 Hyperlink Technologies, Inc.