Autoguide TURF TROOPER 3 Operator's Manual
  1. Manuals
  2. Brands
  3. Autoguide Manuals
  4. Lawn Mower
  5. TURF TROOPER 3
  6. Operator's manual

Autoguide TURF TROOPER 3 Operator's Manual

Ride-on mower
Hide thumbs
Table of Contents

Advertisement

Quick Links

OPERATORS MANUAL
&
SPARE PARTS LIST
TURF TROOPER 3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TURF TROOPER 3 and is the answer not in the manual?

Questions and answers

Summary of Contents for Autoguide TURF TROOPER 3

  • Page 1 OPERATORS MANUAL & SPARE PARTS LIST TURF TROOPER 3...

  • Page 6: Table Of Contents

    CONTENTS Page CERTIFICATE OF CONFORMITY SPECIFICATIONS INTRODUCTION SAFETY INSTRUCTIONS ASSEMBLING THE MACHINE OPERATING THE MACHINE SAFETY INTERLOCK SWITCHES TO START THE ENGINE TO STOP THE ENGINE STEERING WORKING INSTRUCTIONS SPEED CONTROL CYLINDER DRIVE CLUTCH CUTTING WITH THE MACHINE THROTTLE CONTROL BRAKE &...

  • Page 7: Certificate Of Conformity

    EC DECLARATION OF CONFORMITY I, the undersigned, of Allen Power Equipment Ltd., The Broadway, Didcot, Oxon OX11 8ES, certify that the machine described below: - Category Lawnmower Make ALLEN Type Ride-on Model Turf Trooper III Cutter 60” (1530mm) Cylinder Comply with the following Directives. 79/113/EEC 89/336/EEC as amended by 92/31/EEC 89/392/EEC...

  • Page 8: Specifications

    SPECIFICATIONS MODEL ENGINE GXV 270 MANUFACTURER Honda POWER HP MAX PERMISSIBLE (KW) ENGINE SPEED (RPM) 3600 SOUND POWER LEVEL (LWA) dB(A) SOUND PRESSURE LEVEL (LPA) dB(A) 86.4 EXPLANATION OF SYMBOLS Warning Read Instruction Manual before operating Engaged Parking Brake Disengaged Engaged Cutter clutch Disengage...

  • Page 9: Introduction

    INTRODUCTION SAFETY INSTRUCTIONS The ALLEN TURF TROOPER 3 is an advanced Please ensure that the instructions ride-on cylinder mower designed to cut grass contained in this manual are read quickly, efficiently and economically, giving your carefully and fully understood by any person lawn the velvet finish only a quality cylinder likely to operate the Trooper.

  • Page 10: Assembling The Machine

    The seat is fitted with a safety cut-out switch ASSEMBLING THE MACHINE which stops the engine as soon as the operator dismounts unless certain parameters are met. The machine comes partially assembled however Should this happen, the ignition switch must also the following operations are necessary prior to be turned off to prevent the battery discharging.

  • Page 11: Safety Interlock Switches

    WORKING INSTRUCTIONS With the engine running at full speed, the SAFETY INTERLOCK SWITCHES machine may be used in either travelling or cutting mode. If travelling, ensure that all the The machine is fitted with a number of interlock switches to give additional safety to the customer.

  • Page 12: Cutting With The Machine

    THROTTLE CONTROL CUTTING WITH THE MACHINE The Throttle Control ‘I’, Fig 6 is a combined The Trooper is designed to have all three choke and engine speed control housed in one cylinders operating at the same time. There is no unit.

  • Page 13: Lubrication

    If working on lifted parts ensure that adequate Use Castrol L.M. grease or equivalent. support is provided. Occasionally lubricate all other moving parts by Do not alter engine speed above the maximum oil can, in particular the Throttle Control at the quoted in the engine specification.

  • Page 14: Cylinder Drive Belt Adjustment

    If belt replacement is necessary, remove the CYLINDER CLUTCH ADJUSTMENT main access panel as detailed above ‘R’. Then remove the Locating Spigot Bar from the The clutch is designed to be partially self- fan/pulley assembly, Fig. 15 and separate the adjusting, however periodic inspection should be fan/pulley assembly, Fig.

  • Page 15: To Adjust

    necessary. Removal of the Cylinder Belt greatly GUARANTEE eases this operation. If there is any component, or components, Note: manufactured by ALLEN POWER EQUIPMENT LTD that is found to be defective within 12 months from the date of purchase (or in the case The performance of a blunt cylinder/bottom blade of a machine used for hire purposes, 45 days).
  • Page 18 !" " "...
  • Page 20 &...
  • Page 22 " " " ! " " ( " " "...
  • Page 24 " " !" " " " " " " " " "...

  • Page 26: Cutting Cylinder Assemblies

    CUTTING CYLINDER ASSEMBLIES ITEM No. PART No. DESCRIPTION 27984 REEL ASSEMBLY (LH) 27985 REEL ASSEMBLY (RH) 27983 REEL ASSEMBLY (REAR) 23917 BODY (LH) BODY (RH) BODY (REAR) 02137 GREASE NIPPLE 23741 PULLEY 03467 ROLL PIN 23979 GUARD (LH) 23980 GUARD (RH) 23981 GUARD (REAR) 23985...
  • Page 28 !" " +...
  • Page 30 " " "...
  • Page 32 " " , -../01.23.-0./0 , -../01.2/-0.4 , -../01.2/5675/-8./05-.20 % 9 -../01./0:75-8 "...
  • Page 34 Heddington, Nr Calne, Wiltshire, SN11 0PS Telephone: +44 (0) 1380 850885 Fax: +44 (0) 1380 850010...

Table of Contents

Save PDF