Allworx PX 6/2 Installation Manual
  1. Manuals
  2. Brands
  3. Allworx Manuals
  4. Extender
  5. Px 6/2
  6. Installation manual
Allworx PX 6/2 Installation Manual

Allworx PX 6/2 Installation Manual

Expander px 6/2
Hide thumbs Also See for PX 6/2:
Table of Contents

Advertisement

Quick Links

®
Allworx
Px 6/2
Expander
Installation Guide

Advertisement

Table of Contents
loading

Related Manuals for Allworx PX 6/2

Summary of Contents for Allworx PX 6/2

  • Page 1 ® Allworx Px 6/2 Expander Installation Guide...
  • Page 2 Allworx. © 2008 Allworx, a wholly owned subsidiary of PAETEC. All rights reserved. Allworx is a registered trademark of Allworx Corp. All other names may be trademarks or registered trademarks of their...

  • Page 3: Table Of Contents

    11.2 Industry Canada............................17 11.3 Radio and Television Interference ......................18 12 Wall Mount Template ..........................20 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03. Revised: May 16, 2008...

  • Page 4: Installation Overview

    1 Installation Overview Note: Use of the Allworx Px 6/2 Expander requires connection to an Allworx 6x, 10x, or 24x server. The server must be equipped with the Internet Call Access Feature Key. Procure the key before beginning installation at the customer site.

  • Page 5: Procuring And Installing The Internet Call Access Feature Key

    Procuring and Installing the Internet Call Access Feature Key Note: Use of the Allworx Px 6/2 Expander requires connection to an Allworx 6x, 10x, or 24x server. The server must be running Release 6.9 and must have the Internet Call Access Feature Key installed. Obtain the key using the following procedure: 1.
  • Page 6 Unpacking Open the box and carefully unpack it. Save all shipping and packaging materials. Verify all items against the parts list shown in Table 1. If any items are missing, contact your dealer or Allworx Customer Support at 866- 255-9679.

  • Page 7: Chassis Views

    Inside Analog Extension LEDs – Indicates status of a particular FXS port Network LED – Indicates Ethernet link status; flashes for activity 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03.
  • Page 8 Ground connecting screw 5.5 x 2.1 mm power jack. Input 12 VDC @ 1A, center positive 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03. Revised: May 16, 2008...

  • Page 9: Mechanical

    Note: The unit must be mounted with the front facing forward, not up or down (see Figure 3). 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03.
  • Page 10 Px 6/2 Expander Installation Guide Figure 3: Wall Mount Orientation Correct Orientation Wrong Orientation 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03. Revised: May 16, 2008 Page 7...

  • Page 11: Electrical

    (See Figure 2 item 10) must be permanently connected to earth using 18 AWG wire or larger. 5.2 Power-Up Sequence Connect the unit’s Network port to an Allworx server LAN. Then connect the AC power adapter. The Port Expander will automatically begin to power up. As it progresses through the power up sequence, the front panel Power LED will flash green.

  • Page 12: Diagnostic Port

    Px 6/2 Expander Installation Guide 6 Diagnostic Port The Diagnostic connector (See Figure 2, Item 5) is a serial port. Should Allworx Customer Support instruct you to capture diagnostic data, connect a null modem serial cable from the Diagnostic connector to the serial port on a PC.

  • Page 13: Port Expander Configuration

    Allworx server. Therefore, the Network port of the Allworx Px 6/2 must be attached either directly or remotely to an Allworx server. This is usually done by connecting to the server LAN through a network switch. . Up to three Port Expanders can be connected to a given server. The diagram below depicts three Port Expanders connected on a server LAN.

  • Page 14: Local Connection

    1. If the Port Expander has already been powered on, disconnect power. 2. Connect the Network port of the Port Expander to the LAN of the Allworx server per the diagram above using a standard RJ-45 category 5 Ethernet cable.

  • Page 15: Remote Connection

    7.3 Remote Connection Allworx Px 6/2 Port Expanders can be configured to run at sites that are remote to the Allworx server. Much like with a remote Allworx phone, this requires manual configuration of the Port Expander. The Boot Server IP (the Allworx Server’s IP) and the server’s Plug and Play Secret Key must be entered within the Port...
  • Page 16 Section 7.1, Configuring the Port Expander Password and entering a new password. 12. Activate the FXO and FXS ports through the Web Admin page on the Allworx Server. Refer to the Allworx System Administrator’s Guide for Release 6.9 or higher for information on configuring the ports.

  • Page 17: Telephone Line Connection

    The Power Fail Phone port may be used to connect an analog phone device that is operational in the event that the Port Expander loses power, if it loses its network connection to the Allworx server, or if some other hardware failure occurs.

  • Page 18: Data Network Connection

    Blinking Activity: data is being transmitted or received Table 5: Network Port LED Definitions 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03. Revised: May 16, 2008...

  • Page 19: Physical And Environmental Specifications

    Humidity 15% ~ 90% RH, Non-condensing Table 6: Physical and Environmental Specifications 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03. Revised: May 16, 2008...

  • Page 20: Regulatory Notices

    300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03.

  • Page 21: Radio And Television Interference

    Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington D.C. 20402. 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03. Revised: May 16, 2008...
  • Page 22 A préscrites dans le Règlement sur le brouillage radioélectrique édicte par le Ministere des Communications du Canada. 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03.

  • Page 23: Wall Mount Template

    Px 6/2 Expander Installation Guide 12 Wall Mount Template 300 Main Street • East Rochester, NY 14445 • Toll Free 1-866-ALLWORX • 585-421-3850 • www.allworx.com © 2008 Allworx. All rights reserved Version 03. Revised: May 16, 2008 Page 20...

Table of Contents