Advertisement
Rev. Level
C
D
E
Page 6: add "effectively reverses relay polarity"
Page 10: replace "access code to 3446" with "System ID"
This product is designed to be installed and maintained by professional
security technicians.
Unless specifically noted, Inovonics products are intended for indoor use. This
receiver is intended for use with indoor security systems. Use in outdoor
applications may impair performance.
Test system regularly.
FA416 / FA416D
FA416R / FA416DR
Frequency Agile
16-Channel / 4-Output Receiver
Installation Instructions
02304E
Document revision history
Description
Create F:\Eng\parts\02304\02304C.doc from
P:\Master.dox\FA_dox\FA416_v3.doc
Replace ISO logo
Page 5: replace "95%" with "90%"
Important Notes
®
900MHz
Date
7/19/01
10/08/01
10/29./02
Advertisement
Table of Contents
Related Manuals for Inovonics FA416
Summary of Contents for Inovonics FA416
-
Page 1: Installation Instructions
This product is designed to be installed and maintained by professional security technicians. Unless specifically noted, Inovonics products are intended for indoor use. This receiver is intended for use with indoor security systems. Use in outdoor applications may impair performance. - Page 2 With the FA116, users can program 16 points into the FA416 without the FA516 display module. The FA116 also has a signal level and signal margin monitoring function, making it very useful for site surveys and troubleshooting.
- Page 3 OUTPUT 4 FAULT FA416 16 Channel Receiver by Inovonics Corporation Shown with access door removed. To remove, insert small screwdriver and gently pry door off. Figure 4: FA416 / FA416R receiver housing © 1997 Inovonics Wireless Corporation LIT-FA416-INSTALL 02304e 23-Oct-02...
- Page 4 • Technicians can observe output function by monitoring voltages between channel outputs and power on the FA416 or resistance on the FA416R relay outputs. • Transmitter, receiver and output options are factory assigned. They may be changed with the FA116 Executive Programmer or with the FA104 (upgraded C104) programmer.
-
Page 5: Technical Specifications
FA516 Display Module. Visually check the mating of pins and header to make sure that all pins are seated in the header. Note: If the FA516 display is purchased separately from the FA416, it will be packaged with a housing cover and graphic panel to replace the original FA416 cover. (Specify housing type.) Installing the case tamper: Connect leads from the Case Tamper terminal block to a zone on the hardwire panel. - Page 6 Connecting FA416-version receivers to a panel: When the FA416 will be used with a hardwire security panel, the panel will supply 12VDC power and ground to the FA416. Typically, the ground supplied to the receiver is common to the input loops of the hardwire panel. NOTE: Ground from the panel to the receiver MUST be common on the FA416 and FA416D.
-
Page 7: Programming Transmitters
2. Select a point number which matches desired transmitter parameters. 3. Press the Advance button on the FA416 as often as needed to turn on the Output LED for the desired transmitter channel. (Output LED 1 equals point # 1, etc.) The LED will blink if the point has not been programmed. -
Page 8: Receiver Operation
Output Select Jumper. (If the jumper position is changed after transmitters have been programmed, it will be necessary to press the receiver Reset Button.) Activation of an output is indicated by the corresponding Output LED on the FA416 board. The fifth LED is the Global Fault LED. -
Page 9: Troubleshooting Guide
Deleting points with the FA516: Points 1 through 16 may be deleted. 1. Use the Advance button to show the desired point on the Channel Display. 2. Press the Delete button on the FA416 board. The Programmed LED will change from steady "on" to flashing. - Page 10 Absolutely nothing. They are separate options. Transmitters can be programmed as Normally Open or Closed devices, or any combination thereof, and the output loop can be Normally Open or Normally Closed, according to the needs of the system. © 1997 Inovonics Wireless Corporation LIT-FA416-INSTALL 02304e 23-Oct-02...
- Page 11 Seconds *Only points 1 through 4 can be programmed from the FA416 and FA416R. Points 1-16 may be programmed from the FA416D and FA416DR. The FA116 programmer can be used to change any transmitter options on any receiver for all 16 points.
-
Page 12: Smoke Detector
3.75" x 5.75" x 2.50" Note: Batteries are always supervised. Lithium batteries are capacity-tested at 18-hour intervals. Typical battery life is based on 60-second check-in. The transmitter will deactivate 2 weeks after low battery is detected. © 1997 Inovonics Wireless Corporation LIT-FA416-INSTALL 02304e 23-Oct-02... - Page 13 1.25" x 6.00" x 0.750" Note: Batteries are always supervised. Lithium batteries are capacity-tested at 18-hour intervals. Typical battery life is based on 60-second check-in. The transmitter will deactivate 2 weeks after low battery is detected. © 1997 Inovonics Wireless Corporation LIT-FA416-INSTALL 02304e 23-Oct-02...
-
Page 14: Appendix D Warranty & Disclaimer
60 SEC 60 SEC 60 SEC 60 SEC 60 SEC 60 SEC 60 SEC 60 SEC 60 SEC 60 SEC 60 SEC 60 SEC 60 SEC 60 SEC Appendix D Warranty & Disclaimer © 1997 Inovonics Wireless Corporation LIT-FA416-INSTALL 02304e 23-Oct-02... - Page 15 This warranty will not be modified, varied or extended. Inovonics does not authorize any person to act on its behalf to modify, vary or extend this warranty. This warranty will apply to Inovonics Products only. All other products, accessories or attachments used in conjunction with Inovonics equipment, including batteries, will be covered solely by their own warranty, if any.
- Page 16 16-channel / 4-relay output with display FA464DR 64-channel / 16-relay output with display Receiver Accessories: FA116 Executive Programmer for FA416 / FA464 / C404 FA516 Display module for FA416 and FA416R FA541 Single-channel form ‘C’ relay module Inovonics Wireless Corporation...
Need help?
Do you have a question about the FA416 and is the answer not in the manual?
Questions and answers