Connection To The Swell Pedal And Pedalboard; Connection To The Farfisa Amplifiers Models; Separate Amplification Of Treble And Bass; Connection To Current Network - Farfisa Combo Compact User Manual

To assemble the Swell pedal (fig. D) loosen screws
and fix it by tightening screws
( 1 1
legs fig. C) at the right of the player. Using the same procedure, the pedalboard is to be as­
sembled at the left.
The Multi-tone-Booster lever
position.

CONNECTION TO THE SWELL PEDAL AND PEDALBOARD

The plug ( 12 fig. C) is to te inserted into the input at the back of the base of swell pedal,
taking care the reference mark is downwards.
The connector of the pedalboard is to be inserted into the input under the instrument
B). The wire of swell pedal is to be fixed t o the grips
board is to
be fixed to the grips
The other two wires, the one with a plug at one end and the other one for connection to the
be
mains, are to fixed to the grips

CONNECTION TO THE FARFISA AMPLIFIERS MODELS

Take care the knobs ( 16, 17, 18, 31, f
Insert plug ( 13 f ig
C) into the
.
GAN input there is a switch for« BASS » and« TREBLE », Switching on
performance from Compact, whi · l e swi t c hing on « TREBLE », you emphasize sharp incisive tunes ,
particularly reqvired by modern music.
More power can be obtained Inserting plug into input No.2 of the 2nd channel of FARFISA «20Jt.
and ». In this case th e
« 40
When using an amplifier other than FARFI SA MODEL

SEPARATE AMPLIFICATION OF TREBLE AND BASS

Wishing to have a separate amplification
fier for Bass ( Farfisa mo de l

CONNECTION TO CURRENT NETWORK

The cable for connection to the mains
wires of different colours: RED and BLAK for the mains; BLUE or GREEN for connection to ground.
The connection to ground may be useful to avoid buzz deriving from the current network.
Compact works on A.C. 50/60Hz, 110/240 V.
Before connecting to the mains, be sure the voltag
tage of the network.
It is dangerous to open the instrument when it is connected to the current n e t ­
Im p ortant:
work. internal I pecti
When ns
USE OF EARPHONE
The earphone outlet, placed near the ON/OFF switch, is meant for the use of an earphone
with impedance 2000
+
performance, when lt is
( 19).
Connect recesses
fig. B) must te taken out of the hook and put in vertical
( 8
fig.
(
B}.
6b
( 6c fig.
B), taking care to fix 'the first the thinner wire.
.
i
g C) are completely turned clockwise.
ORGAN » input of the FARFISA amplifiers Close to the OR­
«
and «MEDIUM» push buttons are to be inserted.
BASS
« :t
of
Treble and Bass insert the plug of a second ampli­
BT
40 is recommended) into input 32 fig.
( 14
f i g
n i needed, first disconnect
o
2000. In addition to silent practice, this is really useful for controlling a
directl y r
e c o d e d into a tape recorder, without using the
r
( 19)
and slide outwards plate {20)
( 21 )
to the studs of the bar across the
( 6a
fig. B), while the wire of the pedal­
20 40
AND
BASS», you get standard
«
and see sp ecial instructions.
«20» «40»,
C.
.
C) is supplied without plug a nd contains three
e ( 15
switch fig. C) shows the correct vol·
mains.
the
(7
fig.
amplifier.
5