Subscribe to Our Youtube Channel
Related Manuals for MyBinding RSC 1650H
Summary of Contents for MyBinding RSC 1650H
- Page 1 Royal Sovereign RSC 1650H/HR & 1650C Laminators Instruction Manual Provided By http://www.MyBinding.com http://www.MyBindingBlog.com...
- Page 2 17. WARRANTY Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are warranted for Six (6) months. This warranty is extended only to the original purchaser.
-
Page 3: Table Of Contents
RSC Series TABLE OF CONTENTS 1. INTRODUCTION TOPIC PAGE Thank you for choosing a Royal Sovereign laminator. It has been designed and manufactured to provide years of continuous service. For complete operating and 1. Introduction......................2 maintenance information please read this manual thoroughly. Upon receipt of your 2. -
Page 4: Installation
RSC Series 3. INSTALLATION 4. INCLUDED WITH LAMINATOR Thoroughly inspect the parts and the unit. It is imperative that any missing parts are Note: The laminator should be installed by a trained service technician. reported and a claim is filed with the reseller immediately upon receipt of shipment. The laminator comes fully assembled, except for the feed table, paper guide, and heat assembly (RSC-1650H and RSC-1650HR) to avoid shipping damage. -
Page 5: Product Identification
RSC Series 5. PRODUCT IDENTIFICATION 6. CONTROL PANEL When the machine is initially turned on, the LED display window will show the speed and temperature set at 1. (RSC-1650H and RSC-1650HR). ? O ? h e ? ? h e ? ? h e ? ? h e ? ? h e ? -
Page 6: Roller Nip Settings
RSC Series 7. SPEED AND TEMPERATURE SETTINGS 9. USING FOOT PEDAL AND REMOTE CONTROL USING FOOT PEDAL RSC-1650H/C/HR R S C - 1 6 5 0 H R S C - 1 6 5 0 H R Place the foot pedal on the floor in front of the Speed# Speed(Ft/min,M/min) T e m p . -
Page 7: Using Cross Cutter
RSC Series 10. USING CROSS CUTTER 11. LOADING FILM Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in). The cross cutter is located on the rear exit table of the machine. Loading films to the top and bottom film shafts: (See page 5 for assistance with parts identification.) 1. -
Page 8: Threading Film
RSC Series 9. Cut and separate the release liner and the film. 12. THREADING FILM (Figure 3) Figure 3 10. Thread the craft paper behind the Lower Idle Bar to the top film that is resting on the main roller (do not use the Lower Idle Bar for Mounting). -
Page 9: Mounting
RSC Series 17. Press the Stop button when the leader board has completely exited from the rollers. 4. Flip the image over the top roller and hold on to the release liner (Figure 4). 18. Use the Cross Cutter to cut the leader board from the web (see page 9). 19. - Page 10 RSC Series 4. Disassemble the power switch bracket and place the left 13. INSTALLATION OF FRONT FEEDER and REAR rewinder outside of the frame; fasten with round head REWINDER OPTIONS 3/16"(M5) screws (included in the option kit). Then, reinstall the power switch bracket (Figure 7). Note: Below options are to be installed by an authorized RS reseller.
-
Page 11: Maintenance
RSC Series 14. MAINTENANCE 16. SPECIFICATIONS Cleaning the Body of the laminaor 1. To clean the machine body, dampen a cloth with water only and gently wipe the machine clean. Removing Adhesive Build Up 1. Remove the film from the laminator. 2.
Need help?
Do you have a question about the RSC 1650H and is the answer not in the manual?
Questions and answers