1. Manuals
  2. Brands
  3. MICROBEE Manuals
  4. Modem
  5. PCFW-104
  6. User manual

MICROBEE PCFW-104 User Manual

Radio modem pc/104 interface
Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
PCFW-104 M-Series Radio Modem
PC/104 Interface User's Manual
MICROBEE SYSTEMS CORPORATION
9414 Danese Lane SE
Huntsville, AL 35803
Tech. Support: 256–426–2431
www.microbee-systems.com
support@microbee-systems.com
COPYRIGHT 2002 MicroBee Systems Corporation.
All rights reserved.
However, any part of this document may be reproduced, provided that MicroBee Systems
Corporation is cited as the source. The contents of this manual and the specifications herein may
change without notice.
TRADEMARKS:
Windows® is a registered trademark of Microsoft Corporation.
ROM-DOS is a trademark of Datalight.
QNX is a trademark of QNX Software Systems, Ltd
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PCFW-104 and is the answer not in the manual?

Questions and answers

Summary of Contents for MICROBEE PCFW-104

  • Page 1 COPYRIGHT 2002 MicroBee Systems Corporation. All rights reserved. However, any part of this document may be reproduced, provided that MicroBee Systems Corporation is cited as the source. The contents of this manual and the specifications herein may change without notice.
  • Page 2 The possibility of failure can be caused by the external application of input voltage to the radio via the external B+ input while the PCFW-104 power is off. If you apply 5V to the input of a TTL chip with the power off, nothing will happen. Applying a 5V input to a CMOS card will cause the current to flow through the input and out the 5V power pin.

  • Page 3: Technical Support

    MicroBee Systems does not guarantee operation with unusual or custom operating systems. If you have a question about the PCFW-104 card and cannot find the answer in this manual, call Technical Support. They will be ready to give you the assistance you need.

  • Page 4: Operating Precautions

    3.6 in. x 3.8 in x 0.6 in. 91.4 mm X 96.5 mm x 15.2 mm INSTALLATION Before installing the PCFW-104 Radio Modem, refer to Figure 1 for the location of various connectors and jumpers. Interrupt Select Jumpers, JP1 JP1 is used to select the IRQ Level. IRQ's 3, 4,5,7, 10, 11, 14 and 15 are supported.
  • Page 5 X = jumper installed meaning bit = 0. Radio Power In order to provide maximum flexibility for the user the PCFW-104 allows for powering of the Radio Module from either the PC/104 Bus 12 VDC supply or an external 6-30 VDC source.
  • Page 6 Since the PCFW-104 is to be used in remote embedded applications inside a case Connector J5 is available to facilitate the installation of a external setup switch. Shorting the pins on J5 invokes the user setup menu.

  • Page 8: Limitations On Warranty

    MicroBee’s obligation under this warranty shall not begin until Buyer returns the defective product, freight prepaid to MicroBee’s facility or another specified location. MicroBee’s only responsibility under this warranty is, at its option, to replace or repair, free of charge, any defective component part of such products.

  • Page 9: Governing Law

    There will be a 15% restocking charge on returned product that is unopened and unused, if MicroBee accepts such a return. Returns will not be accepted 30 days after purchase. Opened and/ or used products, non-standard products, software and printed materials are not returnable without prior written agreement.

This manual is also suitable for:

Pcfw-104 m-series

Table of Contents