Table of Contents
Advertisement
Quick Links
IVIE Enterprises
www.ivie-ent.com
Ph:(918)254-5161 or (888)262-5161 Fax:(918)250-4807
Super 7R
Operator's
Manual
Edger
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your American
Sanders Technology machine could result in injury to you or to other personnel; damage to the machine
or to other property could occur as well. You must have training in the operation of this machine before
using it. If you cannot read English, have this manual explained fully before attempting to operate this
machine.
Si Ud. no pueden leer el Inglés, se hagan explicar este manual completamente antes de tratar el
manejo o servicio de esta máquina.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: ALTO U.S. INC., 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 78155B
10/01
AMERICAN SANDERS TECHNOLOGY
Printed in the U.S.A.
Advertisement
Table of Contents
Summary of Contents for Alto 07011A
- Page 1 All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: ALTO U.S. INC., 2100 Highway 265, Springdale, Arkansas 72764. Form No. 78155B...
-
Page 2: Table Of Contents
Contents of this Book Operator's Manual - Section I Operator Safety Instructions ............3 Machine Specifications ..............5 Sanding Cuts and Sandpaper ............ 6 Machine Set-Up ................7 Operating Instructions ..............7 Adjustment Procedures ..............8 Routine Maintenance..............8 Carbon Brushes..............8 Dust Bag ................ -
Page 3: Operator Safety Instructions
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER means: Severe bodily injury or death can occur to you or other personnel if the DANGER statements found on this machine or in this Owner's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Owner's Manual and on your machine. - Page 4 DANGER: Electrocution could occur if the machine is used on a power circuit that repeatedly trips or is undersized. Have a licensed electrician check the fuse, circuit breaker or power supply. DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that is not properly disconnected from the power source.
-
Page 5: Machine Specifications
Control Switch Work Light Operating Handles Wall Guard Abrasive Wrench Steel Reinforced Molded Rubber Sanding Pad Specifications Model 07011A 07075A 07054A Electrical Rating 115V, 12.0 A, 50-60 Hz 115V, 12.0 A, 50-6- Hz 230V, 6.0A, 50-60 Hz Storage Case Optional Standard... -
Page 6: Sanding Cuts And Sandpaper
SANDING CUTS AND SANDPAPER Initial Cut The purpose of the initial cut is to remove old finish and gross imperfections on the floor surface. A coarse abrasive should be used. If glazing, loading, or burning takes place immediately into an initial cut, select a coarser abrasive. If this should occur during an initial cut, the abrasive has dulled and must be replaced. -
Page 7: Machine Set-Up
MACHINE SET-UP 1. Familiarize yourself with the machine. Read all danger, warning, and caution statements and the Owner's Manual before operating this machine. If you or your operator cannot read English, have this manual explained fully before attempting to operate this machine. 2. -
Page 8: Adjustment Procedures
OPERATING INSTRUCTIONS cont. DANGER: Failure to disconnect the supply cable from machine whenever servicing, replacing abrasive, or emptying the dust bag could result in electrocution or severe injury. Never leave machine unattended while the supply cable is connected. DANGER: Never leave dust bag unattended with sanding dust in it.
Need help?
Do you have a question about the 07011A and is the answer not in the manual?
Questions and answers