Related Manuals for Power works 51112
Summary of Contents for Power works 51112
- Page 1 1600 PSI / 1.3 GPM ELECTRIC PRESSURE WASHER 51112 OPERATOR’S MANUAL TOLL-FREE HELPLINE: 1-855-470-2181 powerworkstools.com Read all safety rules and instructions carefully before operating this tool.
- Page 2 Cleaning Units 2080 C.U 24.47 lbs (11.10 kg)
-
Page 3: Ground Fault Circuit Interrupter Protection
W A R N I N G Read and understand all instructions W A R N I N G When using this product basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT To reduce the risk of injury, close supervision is necessary when a product is used near children. - Page 4 Know your product. Read the operator’s manual carefully. Learn the machine’s applications To reduce the risk of injury, keep children and visitors away. All visitors should wear safety glasses and be kept a safe distance from work area. Use right product. use it for a purpose not intended.
- Page 5 W A R N I N G High pressure jets can be dangerous if subject to misuse. people, animals, electrical devices, or the machine itself. Check bolts and nuts for looseness before each use. A loose bolt or nut may cause serious motor problems.
- Page 6 Amps...
- Page 7 SYMBOLS SYMBOL NAME DESIGNATION/EXPLANATION USE ACIDS, ALKALINES,BLEACHES, INDUSTRIAL GRADE SOLUTIONS in this product. The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER Indicates an imminently hazardous situation, which, if not WARNING Indicates a potentially hazardous situation, which, if not avoided, CAUTION...
-
Page 8: Electrical Connection
ELECTRICAL W A R N I N G The double insulated system is intended to protect the user from shock resulting from a break in the product’s internal insulation. Observe all normal safety precautions to avoid electrical shock. DOUBLE INSULATED Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual three-wire grounded power cord. - Page 9 Remove the cap from the detergent tank and add detergent.
-
Page 10: Packing List
UNPACKING This product requires assemb ly. Carefully remove the product and any accessories from the bo x. Make sure that all items listed in the packing list are included. W A R N I N G Do not use this product if any parts on the Packing List are already assembled to your product when you unpack it. - Page 11 ASSEMBLY OPERATING THE HANDLE ASSEMBLY (See Figure 2.) Open for use: Lift up on the handle bar pivoting it towards the back into an upright position until it clicks and locks into place. To fold the handle, pull the latch sideways again, and push the handle down and foward.
- Page 12 ASSEMBLING WAND TO PRESSURE WASHER GUN See Figure 5.) Installing Wand to Pressure Washer Gun Insert the male bayonet end(1) of the wand into the female bayonet outlet(3)firmly . While pushing in the wand firmly ,turn clockwise(2)until tabs lock into place to ensure a leak-free connection .
- Page 13 ASSEMBLY CONNECTING THE GARDEN HOSE (See Figure.) C A U T I O N NOTE: There must be a minimum of 10 feet of unrestricted garden hose between the water intake and the garden hose faucet or shut off valve(such as a “Y” shut off connector). Run water through the garden hose for 120 seconds to clean any debris from the hose.
-
Page 14: Operation
OPERATION W A R N I N G Do not allow familiarity with the product to make you careless. Remember that a careless fraction W A R N I N G W A R N I N G Do not use any attachments or accessories not recommended by the manufacturer of this product. W A R N I N G APPLICATIONS You may use this product for the purposes listed below:... - Page 21 If leaving the pressure washer unattended then ensure the following.
- Page 30 TOLL-FREE HELPLINE: 1-855-470-2181 powerworkstools.com...
Need help?
Do you have a question about the 51112 and is the answer not in the manual?
Questions and answers