Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for dbRevO Wireless Tech All-in -One Design
- Page 1 Usage Manual...
-
Page 2: Table Of Contents
Usage Manual I. Usage Notice II. Installation Method ◆Name of Various Parts ◆Installation of Power Wheel ◆Installation of Power-off Brake Levers ◆SENSOR Installation ◆Installation of Console III. Operation Instructions of Console IV. Charging Method ◆To Charge The Console ◆To Charge The Power Wheel V. -
Page 3: Usage Notice
I. Usage Notice (Foreword) Be sure to read and abide by following instructions then abide by traffic rules for your driving safety. Products may be damaged to endanger personal life safety if there is any violation. Be sure to wear safety helmets when driving bicycles. Power wheel may be damaged with speed deceleration due to passengers or heavy articles. -
Page 4: Installation Method
II. Installation Method ◆Name Of Various Parts: Charging hole Power switch Software updating location Power wheel Screw capx2 Truss headhexagon screws Power-off brake levers (M4,M5,M6) Sleeve (M4,M5,M6) Disc brake +Screw x 6 (optional) Console Magnetic disc for sensor Front fork fixation piece sensor Washer x 7 Axle center fixation sheet iron... -
Page 5: Installation Of Power Wheel
◆Installation Of Power Wheel: 2. To lock alignment position of disk 1. To detach front wheel brake wire brake by screw properly. (Disc brake is of general bicycle and front wheel. optional.) (Be sure to detach the entire brake for installation of optional disc brake.) 3. -
Page 6: Installation Of Power-Off Brake Levers
◆Installation Of Power Wheel: 5. To align L. into groove and place 6. To align E. to axle center. into axle center (in charging side) for locking. 7.To install B. onto F. and place into E. 8. To check if tyre is perpendicular to for lock (according to B.C. -
Page 7: Sensor Installation
◆Installation of power failure handle: 12. To adjust power-off brake levers 11. To install back the gearshift and gearshift lever for proper angle lever and handlebar grips. then lock. To fix brake wires then test brake repeatedly to see if it functions well. -
Page 8: Installation Of Console
◆Installation Of Console: 18. Insert console into bracket. 17. Install the bracket on the handlebar. 19. Connect wires to finish the installation. Detachment method is opposite to above steps. Note! Users shall store detached power wheel properly for best condition. -
Page 9: Operation Instructions Of Console
III. Operation Instructions Of Console Speed assistance level selection Mileage Indicator of Power battery switch capacity for Power wheel 2.4G wireless Indicator of battery transmission signal capacity for console Assistant driving force levels ◆ Istructions of data readout on console Speed: Display the speed per hour of the bike by KM/H(Mile), speed range: 0~99.9. - Page 10 ◆Operation Instructions Of Console Indicator of battery capacity for Power wheel Energy column will display full number (namely, 5 BARs) when power volume is full. BAR will flicker (with frequency of once every second) if there are only 2 BARs. It will begin to flicker and alarm to notify users of charging need.
- Page 11 3 to 5 seconds before to power on again. 3.The console and controller will communicate through 2.4G wireless transmission when use dbRevO wheel for the 1 time. 4. Users shall power on the wheel before power on the console. After the console and controller communicate through 2.4G wireless transmission,...
-
Page 12: Charging Method
Suitable ambient temperature for charging is 0~45℃. Users shall charge the battery immediately after using, and to charge at least once every month for better maintenance. Meanings of the LED colors on dbRevO Wheel charger. Green LED Orange LED Green LED... -
Page 13: Maintenance & Repair
1. To check if there’s any rusty part or leaks carefully. Leaks may be eroded to accelerate damage and enlarge the leaks itself. 2. To clean dbRevO wheel periodically and keep away from all corrosive materials such as salt. 3. Do not polish, drill or carve on wheel surface. Leaks may be caused by large scratch, chisel hole or nick. -
Page 14: Error Code (Diagnosis Message)
VI. Error Code Error Code will flicker when control system is under abnormal conditions. The console will be powered off automatically after Error Code flickers for 10 seconds. Troubles And Troubleshooting Trouble Trouble Description Troubleshooting code 1. To check if motor signal wire is disconnected. No speed signal from motor during driving. -
Page 15: Specification
VII. Dimension Form Color Many options Battery Housing Specification Wheel rim 26" Alu-alloy 20'' Alu-alloy Tire 26''X1.95 20''X1.95 G.W. 26''：8.6 kgs 20''：6.4 kgs Power System Specification Motor 24V250W DC Brushless 26'' 20'' Battery 24V8Ah Lithium Battery 24V6.6Ah Lithium Battery Optional 11A Optional 8.8A 24V2A charger for battery &...