Bircher Reglomat InTra6 3 Operating Instructions

InTra6 3, InTra6
Original operating instructions
Safety and warning notices
The electrical connection may only be set up by an electrician.
The arrangement of the components depends on the structural conditions and the gate design.
Switch off the operating voltage before working on the system.
The switching device may only be used to protect against dangers at crushing and shearing points on automatic sliding gates (designated use).
Any other use is prohibited.
Use of components not supplied by Bircher-Reglomat (including safety edges) will render the guarantee and liability null and void.
1 System components
1
Close
5
7
4
1
Close
5
7
2
Electrical connection and terminal diagram
Operating
Version
voltage
InTra6 3
+/~
InTra6 3.LVAC
–/~
3 Operation
«Mode» button
Control buttons
Mode
on device:
4 Standard operation
When everything is connected correctly:
Display after switching on:
Status LED lights up green
5 Diagnose-Modus
« » «
Press the Mode and Data
« »
mode. Press the Mode button for 2 s to exit diagnostic mode.
Error display mode
The 5 most recent errors
can be interrogated.
« »
Press the Data key briefly in
each case, and the errors are dis-
played one after the other. End
« »
appears when the Data button
is pressed for the 5th time. The
malfunctions are displayed in
chronological order (new old)
Mode «S» Both outputs
1 2
– Both outputs deactivated
– No current flow OK
1 2 – At least 1 output with current flow
Error, press the «Data» button
– Both outputs are activated
1 2
– Current flow OK
– At least 1 output without current flow
1 2
Consumer missing
3.LVAC
Switching device with inductive transmission system used in combination with safety edges to
4
3
Open
9
3
2 2
Open
9 6
Stationary safety Stationary safety
edge CLOSE edge OPEN
A1
1
A2 2
Display
«Data» button
1 2
Data
Displays shown when safety edge is actuated: Status LED leuchtet orange
actuated:
Dots
flash
»
buttons simultaneously for 2 s status LED flashes orange. Press
Mode «r» Resistance
The resistances of the
safety edges are displayed
Example:
8 = Resistance between
7 and 9 kohm.
1 = safety edge
To access the next safety edge:
« »
Press the Data button
Mode «C» current configuration
Displays current configuration of
safety edge inputs, see configura-
tion table.
Configuration chapter 6
avoid dangers at crushing and shearing points in sliding gate systems.
Mobile safety edge CLOSE
(primary closing edge)
Mobile safety edge OPEN
Stationary safety edge CLOSE
Stationary safety edge OPEN
INTR-MOB61, converter for
safety edge
Hole
grey
Test input
connection
YE
GN
T2
3
WH
4 T1
+
BN
Info
CLOSE Output
OPEN Output
Mode
Data
Dots
actuated:
1 2
«
Mode
Mode «S» Simulation CLOSE
– CLOSE output is deactivated
1
– No current flow OK
– Current flow error
1
«Data» Taste drücken
– CLOSE output is activated
1
– Current flow OK
– No current flow
1
consumer missing
INTR-MOB62, converter for
mobile safety edge
INTR-FIX60, coil
InTra6 3, switching device
Steel cable (see chapter 9.3)
Hole
red
Coil
Output
CLOSE
RX
14 24
21
11
TX
= Display flashes
actuated: actuated:
1
»
buttons briefly to change to the next
Mode «S» Simulation OPEN
2
– OPEN output is deactivated
– No current flow OK
2 – Current flow error
Press the «Data» button
2
– OPEN output is activated
– Current flow OK
– No current flow
2
consumer missing
Mode «e» current fall-delay time
Displays current fall-delay time,
see fall-delay time table.
Configuration chapter 6
Output
OPEN
2