LED LCD TV Safety Precaution ♦ Do not place the TV on unstable places, from which it may be fell off. ♦ Do not expose the TV to extreme temperature and humid environment. ♦ Avoid subjecting the TV to direct sunlight and other heat sources. ♦...
Page 5
LED LCD TV Please immediately pull out the AC power plug from adapter if there is an abnormal sound or smell or the LED LCD TV has sound but no picture, and contact after sales support. The LED LCD TV should be kept free from rain, damp and dust to prevent electrical shock and short circuits.
Page 6
LED LCD TV Do not place the LED LCD TV on an unstable surface. Do not place naked flame sources, such as lit candles on or near the LED LCD TV. Please pull out the power plug and contact after sales support if there are abnormal objects or water in the TV.
Page 7
LED LCD TV Your television is packaged with the TV stand separated from the cabinet. To setup the TV table stand, please carry out the installation according to the instructions below. Step one Place the TV faced down on a soft cloth or cushion to prevent the panel from being damaged.
LED LCD TV TV Control Panel Introduction for each key...
Page 9
LED LCD TV This LED LCD TV has digital multimedia performance and can be connected to multiple external devices. The following diagram presents the connections to other video and audio appliances. YPbPr1 Audio 1)USB: USB input jack for Multimedia. 2,3)HDMI1/HDMI2: High-definition multimedia interface.
Page 12
LED LCD TV Connecting to Satellite Receiver or Decoder In order to receive TV programs, signal should be received from one of the following signal sources: ♦ Outdoor antenna. ♦ Cable TV network. ♦ Satellite broadcast network. 1. In these three cases, the input cable of antenna or TV network should be plugged in the 75 Ohm coaxial cable jack at the rear side of LED LCD TV.
LED LCD TV 2. If you want to select program number from 10-99: Input the channel number you desired, then press OK to confirm, e.g. select channel 12. 2. If you want to select program number after 99: Input the channel number you desired, then press OK to confirm, e.g.
Page 15
LED LCD TV English Español Français Deutsch Italiano Exit Exit Cancel...
Page 16
LED LCD TV Picture Mode User Press the “ ” button to select the “Picture Mode” item, and then use “ ” button to adjust the preset picture mode. Note: Only in User mode you can adjust brightness, contrast, saturation, etc. Picture Mode User Picture Mode...
Page 19
LED LCD TV Sound Mode Sound Mode Press the “ ” button to select the “sound Mode” item, and then use “ ” button to adjust the preset sound mode. Sound Mode Sound Mode Sound Mode Sound Mode Sound Mode Sound Mode...
Page 20
LED LCD TV Sound Mode Sound Mode Sound Mode Sound Mode...
Page 21
LED LCD TV Country Country Region Channels Country Country Region Channels Country Channels Country Region Channels Channel Scan Channel Scan Digital Channel Range Scan Analog Manual Scan Update Scan Channel Skip Channel Sort Note: Channel Scan function will clear the current channel list and perform a new one.
Page 22
LED LCD TV Channel Scan Digital Channel Range Scan Digital Channel Range Scan Analog Manual Scan Update Scan Channel Skip Press the “ ” button to select the “Digital Channel Channel Sort Range Scan” item, and then use “ ” or “OK” buttons to enter digital channel range scan sub-menu.
Page 23
LED LCD TV Channel Scan Digital Channel Range Scan Analog Manual Scan Update Scan Channel Skip Channel Sort your Channel Scan Digital Channel Range Scan Analog Manual Scan Update Scan Channel Skip Channel Sort Press the “ ” button to select the first channel, press OK button;...
Page 24
LED LCD TV Channel Scan Digital Channel Range Scan Analog Manual Scan Update Scan Channel Skip Channel Sort Press the “ ”button to select the “Channel Number” or ‘‘Frequency’’item, and then use the numeric key “0-9” on the remote control to input the channel number or frequency.
Page 25
LED LCD TV Press the “ ” button to select the “Day Light” item, and then use “ ” buttons to select day light on/off. Note: If you turn on the Day Light function, the TV time will become daylight saving time, which pulls ahead for an hour than the standard time.
Page 26
LED LCD TV Pressing the Standby button to turn off the LED LCD, the setup time will be retained. If the unit is unplugged, or main power is otherwise disrupted, the memory for time will be lost. The following items are active only when you select “Off”...
Page 27
LED LCD TV DTV mode. Restriction of Access No Block Press the “ ” button to select the block level: R, AV, MA, M, PG, G.
Page 28
LED LCD TV Note: if you want to unlock the input source, press the ‘ MTS’’ button on the remote control to display ‘ password menu, then input the password (the Multimedia initial password is 0000), the input source will unlock.
LED LCD TV 1. Enter into Multimedia mode Please insert the mobile storage device to the USB input S-Video jack on the back panel of TV first (see page 8). After connecting the device, press the “SOURCE” button on YPBPR 1 remote control or TV front panel to display the source list, YPBPR 2 use the “...
Page 30
LED LCD TV The remote control doesn’t work...
Page 31
LED LCD TV Product name: Color LED LCD TV Power: Less than 150W...
Need help?
Do you have a question about the LEDTV42FHD and is the answer not in the manual?
Questions and answers