Jeep Grand Cherokee Owner's Manual

Jeep Grand Cherokee Owner's Manual

2009 jeep
Hide thumbs Also See for Grand Cherokee:
Table of Contents

Advertisement

GRAND CHEROKEE 2009 owner's manual
I n f o r ma t i o n P r o v i d e d b y :

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Grand Cherokee and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Jeep Grand Cherokee

  • Page 1 GRAND CHEROKEE 2009 owner’s manual I n f o r ma t i o n P r o v i d e d b y :...
  • Page 2 VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of Chrysler LLC shall be deemed to be deleted and the features and equipment that are either standard or op- name Chrysler Canada Inc.
  • Page 3: Table Of Contents

    TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
  • Page 4 I n f o r m a t i o n P r o v i d e d b y :...
  • Page 5 INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....8 Rollover Warning .
  • Page 6: Introduction

    4 INTRODUCTION INTRODUCTION working the vehicle, don’t overload the vehicle or expect This is a specialized utility vehicle designed for both the vehicle to overcome the natural laws of physics. on-road and off-road use. It can go places and perform Always observe federal, state, provincial and local laws tasks for which conventional two-wheel drive enclosed wherever you drive.
  • Page 7: Rollover Warning

    INTRODUCTION 5 NOTE: After you read the manual, it should be stored in Do not attempt sharp turns, abrupt maneuvers, or other the vehicle for convenient reference and remain with the unsafe driving actions that can cause loss of vehicle vehicle when sold so that the new owner will be aware of control.
  • Page 8: How To Use This Manual

    6 INTRODUCTION Failure to use driver and passenger seat belts provided HOW TO USE THIS MANUAL is a major cause of severe or fatal injury. In fact, the U.S. Consult the Table of Contents to determine which section government notes that the universal use of existing seat contains the information you desire.
  • Page 9 INTRODUCTION 7 I n f o r m a t i o n P r o v i d e d b y :...
  • Page 10: Warnings And Cautions

    8 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
  • Page 11: Vehicle Modifications/Alterations

    INTRODUCTION 9 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death. I n f o r m a t i o n P r o v i d e d b y :...
  • Page 12 I n f o r m a t i o n P r o v i d e d b y :...
  • Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....14 Vehicle Security Alarm ....20 Wireless Ignition Node (WIN) .
  • Page 14 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Express Down Window Feature — If Power Windows ..... . 31 Equipped ......24 Wind Buffeting .
  • Page 15: Things To Know Before Starting Your Vehicle

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Seat Belts And Pregnant Women ..45 Transporting Passengers ....69 Seat Belt Extender .
  • Page 16: A Word About Your Keys

    14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Your vehicle uses a keyless ignition system. This system consists of a Remote Keyless Entry (RKE) transmitter with integrated ignition key and a Wireless Ignition Node (WIN) with integral ignition switch. You can insert the double-sided key into the ignition switch with either side up.
  • Page 17: Integrated Ignition Key

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Integrated Ignition Key The integrated ignition key operates the ignition switch. It also contains the Remote Keyless Entry (RKE) trans- mitter and a valet key, which stores in the rear of the RKE transmitter.
  • Page 18 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Settings (Customer-Programmable Features)” under • If you try to remove the key before you place the shift “Electronic Vehicle Information Center (EVIC)” in lever in PARK, it may become trapped temporarily in Section 4 of this manual.
  • Page 19: Key-In-Ignition Reminder

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Key-In-Ignition Reminder the vehicle. The system will shut the engine off in two If you open the driver’s door with the integrated ignition seconds if an invalid RKE transmitter is used to start the key in the ignition, a chime will sound to remind you to engine.
  • Page 20: Replacement Keys

    18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: the vehicle. Once an RKE transmitter is programmed to a • The Sentry Key Immobilizer system is not compatible vehicle, it cannot be programmed to any other vehicle. with aftermarket remote starting systems. Use of these CAUTION! systems may result in vehicle starting problems and loss of security protection.
  • Page 21: Customer Key Programming

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: When having the Sentry Key Immobilizer 3. Insert a blank integrated key into the ignition switch system serviced, bring all vehicle RKE transmitters with and turn the ignition switch to the ON position within you to the authorized dealer.
  • Page 22: General Information

    20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE General Information NOTE: The Panic and Security alarms are quite differ- The Sentry Key system complies with FCC rules Part 15 ent. Please take a moment to activate the Panic and the and with RSS-210 of Industry Canada.
  • Page 23: To Disarm The System

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Vehicle Security Alarm is arming. During this 16 second the alarm will sound. If this occurs, press the UNLOCK arming period, opening any door or the liftgate will button on the RKE transmitter to disarm the Vehicle cancel the arming.
  • Page 24: To Unlock The Doors

    22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Keyless Entry (RKE) transmitter. The RKE transmitter does not need not be pointed at the vehicle to activate the system. NOTE: Inserting the RKE transmitter into the ignition switch disables all buttons on that RKE transmitter; however, the buttons on the remaining RKE transmitters will continue to work.
  • Page 25 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles equipped with the Electronic Vehicle Remote Key Unlock, Driver Door/All Doors First Press Information Center (EVIC), refer to “Flash Lamps with This feature lets you program the system to unlock either Lock”...
  • Page 26: To Lock The Doors

    24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Lock the Doors To Release the Liftgate Flipper Glass Press and release the LOCK button on the RKE transmit- Press the FLIPPER GLASS/TRUNK RELEASE button ter to lock all doors. The turn signal lights will flash and two times (the second press within 5 seconds of the first the horn will chirp to acknowledge the signal.
  • Page 27: Using The Panic Alarm

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Using the Panic Alarm Programming Additional Transmitters To turn the Panic Alarm feature on or off, press and hold Refer to Sentry Key “Customer Key Programming.” the PANIC button on the RKE transmitter for at least one If you do not have a programmed RKE transmitter, second and release.
  • Page 28: General Information

    26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Battery access is through a door located on the rear of 2. Remove and replace the batteries. Avoid touching the the fob. Insert a small, flat blade screwdriver into the slot new batteries with your fingers.
  • Page 29: Remote Starting System - If Equipped

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Doors closed If your Remote Keyless Entry (RKE) transmitter fails to operate from a normal distance, check for these two • Hood closed conditions. • Liftgate closed 1. A weak battery in the RKE transmitter. The expected •...
  • Page 30 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: NOTE: To avoid unintentional shutdowns, the system • If an engine fault is present the vehicle will start and will disable the one time press of the REMOTE START then shut down 10 seconds later. button for two seconds after receiving a valid Remote Start request.
  • Page 31: Door Locks

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 DOOR LOCKS Power Door Locks The power door lock switch is located on each front door Manual Door Locks panel. Press the switch to lock or unlock the doors. Use the manual door lock plunger to lock the doors from inside the vehicle.
  • Page 32: Child Protection Door Lock

    30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you press the door lock switch while the keys are in the This feature is selectable and can be turned on or off. ignition switch, and the driver’s door is open, the doors Refer to “Auto Door Locks”...
  • Page 33: Windows

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position. Child Protection Door Lock WINDOWS Power Windows Power Window Switches The power window controls are located on the driver’s The power window switches remain active for up to door trim panel.
  • Page 34 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down To stop the window from going all the way up during the Both the driver and front passenger window switch has Auto Up operation, push down on the switch briefly. an “Auto Down”...
  • Page 35: Wind Buffeting

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Resetting the Auto Up Feature Should the Auto Up feature stop working, the window probably needs to be reset. To reset Auto Up: Pull the window switch up and close the window com- pletely, then pull and hold the switch for one second.
  • Page 36: Liftgate

    34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE open or partially open positions. This is a normal occur- rence and can be minimized. If the buffeting occurs with the sunroof open, adjust the sunroof opening to minimize the buffeting. LIFTGATE To open the liftgate, pull up (squeeze) on the handle and lift.
  • Page 37: Liftgate Flipper Glass

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Liftgate Flipper Glass WARNING! The liftgate flipper glass is also unlocked when the liftgate is unlocked. To open the flipper glass, push up on To avoid injury, stand back when opening. Glass may the window switch located on the liftgate.
  • Page 38: Occupant Restraints

    36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The front airbags have a multistage inflator WARNING! design. This allows the airbags to have different rates of inflation that are based on collision severity. Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle.
  • Page 39: Lap/Shoulder Belts

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 This feature allows the shoulder part of the belt to move WARNING! (Continued) freely with you under normal conditions. But in a colli- • Buckle up even though you are an excellent driver, sion, the belt will lock and reduce the risk of you striking even on short trips.
  • Page 40: Lap/Shoulder Belt Operating Instructions

    38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) • Two people should never be belted into a single seat belt. People belted together can crash into one another in an accident, hurting one another badly. Never use a lap/shoulder belt or a lap belt for more than one person, no matter what their size.
  • Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
  • Page 42 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tight, tilt the latch plate and pull on the lap belt. A snug WARNING! (Continued) belt reduces the risk of sliding under the belt in a • A belt that is worn under your arm is very danger- collision.
  • Page 43: Adjustable Upper Shoulder Belt Anchorage

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection. Inspect the belt system periodically, checking for cuts, frays, or loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system.
  • Page 44: Automatic Locking Mode - If Equipped

    42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Mode — If Equipped In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. When to Use the Automatic Locking Mode Use Automatic Locking mode anytime a child safety seat is installed in the rear center seating position.
  • Page 45: Energy Management Feature

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 How to Disengage the Automatic Locking Mode WARNING! Disconnect the combination lap/shoulder belt and allow • The belt and retractor assembly must be replaced it to retract completely to disengage the Automatic Locking mode and activate the Vehicle Sensitive (Emer- if the seat belt assembly Automatic Locking Re- gency) Locking mode.
  • Page 46: Enhanced Seat Belt Use Reminder System (Beltalert )

    44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat until the driver’s seat belt is buckled. BeltAlert will be belt placement by the occupant. The seat belt must still be reactivated if the driver’s seat belt is unbuckled for more worn snugly and positioned properly.
  • Page 47: Seat Belts And Pregnant Women

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 3. Within 60 seconds of starting the vehicle, unbuckle Pregnant women should wear the lap part of the belt and then re-buckle the driver’s seat belt at least three across the thighs and as snug across the hips as possible. times within 10 seconds, ending with the seat belt Keep the belt low so that it does not come across the buckled.
  • Page 48: Driver And Front Passenger Supplemental Restraint Systems (Srs)

    46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
  • Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 The front airbags have a multistage inflator design. This may allow the airbags to have different rates of inflation that are based on collision severity and occupant size. This vehicle is equipped with window bags to protect the driver, and front and rear passengers sitting next to a window.
  • Page 50 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Do not have any accessory items installed which • Do not put anything on or around the front airbag will alter the roof, including adding a sunroof to covers or attempt to manually open them.
  • Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 front airbags work with the instrument panel knee bol- WARNING! sters to provide improved protection for the driver and front passenger. Window bags also work with seat belts Infants in rear facing child restraints should NEVER to improve occupant protection.
  • Page 52 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE You should read the instructions provided with your WARNING! child restraint to make sure that you are using it properly. • Relying on the airbags alone could lead to more 2. All occupants should use their lap and shoulder belts severe injuries in a collision.
  • Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 • Front Acceleration Sensors Airbag System Components The airbag system consists of the following: • Driver and Front Passenger Seat Belt Pretensioners • Occupant Restraint Control (ORC) How the Airbag System Works •...
  • Page 54 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The ORC also turns on the Airbag Warning • The Driver and Passenger Airbag/Inflator Units are Light for 2.5 to 8 seconds for a self-check located in the center of the steering wheel and the right when the ignition is first turned on.
  • Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 • The Side Impact SRS Side Curtain Airbags are de- • The Knee Impact Bolsters help protect the knees of signed to activate only in certain side or rollover the driver and the front passenger, and position every- collisions.
  • Page 56 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • It is not advisable to drive your vehicle after the abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium airbags have deployed. If you are involved in another floor.
  • Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 NOTE: The interior lights can only be deactivated if the WARNING! (Continued) key is removed from the ignition switch or the vehicle is • You need proper knee impact protection in a driven.
  • Page 58 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light block for blown fuses. Refer to “Fuses” in Section 7 of this You will want to have the airbag system ready to inflate manual. See your authorized dealer if the fuse is good. for your protection in an impact.
  • Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • Under certain circumstances, EDR data may not be court with legal jurisdiction (i.e., pursuant to a warrant). recorded (e.g., loss of battery power). A copy of the data will be provided to the custodial entity upon request.
  • Page 60: Child Restraints

    58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Transmission gear selection 4. Otherwise required by law. • Cruise control status Data parameters that may be recorded: • Diagnostic trouble code(s) and warning lamp status • Traction/stability control status for electronically-controlled safety systems, including •...
  • Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 enough for an adult safety belt. Always check the child Infants and Child Restraints seat Owner’s Manual to ensure you have the right seat • Safety experts recommend that children ride for your child. Use the restraint that is correct for your rearward-facing in the vehicle until they are at least child.
  • Page 62 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child WARNING! restraint: • Rearward-facing child seats must NEVER be used • Before buying any restraint system, make sure that it in the front seat of a vehicle with the front passen- has a label certifying that it meets all applicable Safety ger airbag unless the airbag is turned off.
  • Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 designed to keep the lap portion tight around the child buckle or latch plate is too close to the belt path restraint so that it is not necessary to use a locking clip. opening on the restraint.
  • Page 64 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: additional information refer belt-positioning booster seat. The child and belt- www.seatcheck.org or call 1-866-SEATCHECK. positioning booster seat are held in the vehicle by the lap/shoulder belt. Older Children and Child Restraints Children who weigh more than 20 lbs (9 kg), and who are Children Too Large for Booster Seats older than one year, can ride forward-facing in the...
  • Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 LATCH — Child Seat Anchorage System (Lower kits or retro-fit kits. You are urged to take advantage of all Anchors and Tether for CHildren) the available attachments provided with your child re- Your vehicle’s rear seat is equipped with the child straint in any vehicle.
  • Page 66 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you are installing LATCH-compatible child restraints The rear seat lower anchorages are round bars, located at in adjacent rear seating positions, you can use the the rear of the seat cushion where it meets the seatback, LATCH anchors or the vehicle’s seat belt for the outboard and are just visible when you lean into the rear seat to position, but you must use the vehicle’s seat belt at the...
  • Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 In addition, there are tether strap anchorages behind each means of adjusting the tension in the strap. Forward- rear seating position located on the back of the seat. facing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
  • Page 68 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For seat belts having an Automatic Locking Retractor WARNING! (ALR), pull the belt from the retractor until there is enough allowance to pass it through the child restraint and slide Improper installation of a child restraint to the the latch plate into the buckle.
  • Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position. To attach a child restraint tether strap: Route the tether strap over the seatback and attach the hook to the tether anchor located on the back of the seat.
  • Page 70: Engine Break-In Recommendations

    68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Drive moderately during the first 300 miles (500 km). WARNING! After the initial 60 miles (100 km), speeds up to 50 or 55 mph (80 or 90 km/h) are desirable. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the While cruising, brief full-throttle acceleration within the child.
  • Page 71: Safety Tips

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 A new engine may consume some oil during its first few WARNING! (Continued) thousand miles (kilometers) of operation. This should be • Do not allow people to ride in any area of your considered as a normal part of the break-in and not vehicle that is not equipped with seats and seat interpreted as an indication of difficulty.
  • Page 72: Safety Checks You Should Make Inside The

    70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not run the engine in a closed garage or in confined damaged, have a competent mechanic inspect the com- areas any longer than needed to move your vehicle in or plete exhaust system and adjacent body areas for broken, out of the area.
  • Page 73: Periodic Safety Checks You Should Make Outside The Vehicle

    THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Airbag Warning Light lodged in the tread. Inspect the tread and sidewall for The light should come on and remain on for six to eight cuts and cracks. Check the wheel nuts for tightness. seconds as a bulb check when the ignition switch is first Check the tires (including spare) for proper pressure.
  • Page 74 I n f o r m a t i o n P r o v i d e d b y :...
  • Page 75: Understanding The Features Of Your Vehicle

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......78 Illuminated Vanity Mirrors — If Equipped . . . 81 Inside Day/Night Mirror .
  • Page 76 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information ....110 Front Heated Seats — If Equipped ..118 Voice Recognition System (VR) —...
  • Page 77 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 Headlights And Parking Lights ..130 Headlight Time Delay ....137 Automatic Headlight System —...
  • Page 78 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed ....146 Overhead Console ..... 153 To Vary The Speed Setting .
  • Page 79 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Opening Sunroof — Express ... . 161 Power Inverter — If Equipped ... . 165 Closing Sunroof —...
  • Page 80: Mirrors

    78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical adjustment of the mirror. The mirror should be adjusted to center on the view through the rear window. Headlight glare from vehicles behind you can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
  • Page 81: Outside Mirrors

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Outside Mirrors To receive maximum benefit, adjust the outside mirrors to center on the adjacent lane of traffic with a slight overlap of the view obtained on the inside mirror. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
  • Page 82: Outside Mirrors Folding Feature

    80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Folding Feature After selecting a mirror, move the knob in the same All outside mirrors are hinged and may be moved either direction you want the mirror to move. Use the center off forward or rearward to resist damage.
  • Page 83: Heated Mirrors - If Equipped

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Power mirror preselected positions can be controlled by the optional Memory Seat Feature. Refer to “Driver Memory Seat” in this Section for further information. Heated Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defroster.
  • Page 84: Uconnect Phone - If Equipped

    • www.dodge.com/uconnect simple voice commands (e.g., Call” “Mike” ”Work or • www.jeep.com/uconnect Dial” “248-555-1212 ). Your cellular phone’s audio is transmitted through your vehicle’s audio system; the •...
  • Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 The uconnect phone is driven through your Bluetooth radio or the mirror has the two control buttons (PHONE “Hands-Free Profile” cellular phone. uconnect features Button and VOICE RECOGNITION button) that will Bluetooth technology - the global standard that enables enable you to access the system.
  • Page 86: Operation

    84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For certain operations, compound commands can be can be adjusted either from the radio volume control knob or from the steering wheel radio control (right used. For example, instead of saying Setup and then switch), if so equipped.
  • Page 87 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Help Command To complete the pairing process, you will need to refer- If you need assistance at any prompt, or if you want to ence your cellular phone Owner’s Manual. The know your options at any prompt, say Help following uconnect website may also provide detailed instructions the beep.
  • Page 88 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • For identification purposes, you will be prompted to Dial by Saying a Number give the uconnect phone a name for your cellular • Press the PHONE button to begin. phone. Each cellular phone that is paired should be •...
  • Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 • The system will prompt you to say the name of the • After the Ready prompt and the following beep, say person you want to call. Phonebook New Entry. • After the Ready prompt and the following beep, say •...
  • Page 90 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Automatic download and update, if supported, begins The uconnect phone will allow you to enter up to 32 names in the phonebook with each name having up to as soon as the Bluetooth wireless phone connection is four associated phone numbers and designations.
  • Page 91 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • This downloaded phonebook cannot be edited or NOTE: • The phone handset must support Bluetooth OBEX deleted on the uconnect phone. These can only be edited on the cellular phone. The changes are trans- transfers of phonebook entries to use this feature.
  • Page 92 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Edit uconnect Phonebook Entries After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in NOTE: the phonebook, call the number you just edited, or return •...
  • Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 • After you enter the Phonebook Delete menu, you will Delete/Erase “All” uconnect Phonebook Entries then be asked for the name of the entry that you wish • Press the PHONE button to begin. to delete.
  • Page 94: Phone Call Features

    92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say cellular service plan. For example, if your cellular service Phonebook List Names. plan provides three-way calling, this feature can be accessed through the uconnect phone. Check with your •...
  • Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 cellular phone. Press the PHONE button to place the Place/Retrieve a Call From Hold current call on hold and answer the incoming call. To put a call on hold, press the PHONE button until you hear a single beep.
  • Page 96 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After the Ready prompt and the following beep, say Three-Way Calling To initiate three-way calling, press the VOICE RECOG- Redial. NITION button while a call is in progress, and make a • The uconnect phone will call the last number that second phone call, as described under Making a Second was dialed from your cellular phone.
  • Page 97: Uconnect Phone Features

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • After the ignition key is switched to OFF, a call can • Continue to follow the system prompts to complete continue on the uconnect phone for a certain dura- the language selection. tion, after which the call is automatically transferred After selecting one of the languages, all prompts and from the uconnect phone to the cellular phone.
  • Page 98 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • If supported, this number may be programmable on If the phone is not reachable and the uconnect phone is operational, you may reach the emergency number as some systems. To do this, press the PHONE button follows: and say ‘Setup’, followed by ‘Emergency’.
  • Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Towing Assistance Paging If you need towing assistance: To learn how to page, refer to Working with Automated Systems. Paging works properly except for pagers of • Press the PHONE button to begin. certain companies, which time out a little too soon to •...
  • Page 100 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When calling a number with your uconnect phone that send the corresponding phone number associated with normally requires you to enter in a touch-tone sequence the phonebook entry, as tones over the phone. on your cellular phone keypad, you can press the VOICE NOTE: RECOGNITION button and say the sequence you wish...
  • Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Turning Confirmation Prompts ON/OFF Dialing Using the Cellular Phone Keypad Turning confirmation prompts off will stop the system You can dial a phone number with your cellular phone from confirming your choices (e.g., the uconnect phone keypad and still use the uconnect phone (while dialing will not repeat a phone number before you dial it).
  • Page 102: Advanced Phone Connectivity

    100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mute/Un-Mute (Mute OFF) uconnect phone or vice versa, press the VOICE REC- When you mute the uconnect phone, you will still be OGNITION button and say Transfer Call. able to hear the conversation coming from the other Connect or Disconnect Link Between the party, but the other party will not be able to hear you.
  • Page 103 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 • The uconnect phone will play the phone names of all • The selected phone will be used for the next phone paired cellular phones in order from the highest to the call. If the selected phone is not available, the lowest priority.
  • Page 104: Things You Should Know About Your Uconnect Phone

    102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your uconnect Repeat the words and phrases when prompted by the phone uconnect phone. For best results, the Voice Training session should be completed when the vehicle is parked uconnect phone Tutorial with the engine running, all windows closed, and the To hear a brief tutorial of the system features, press the...
  • Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • Speak normally, without pausing, just as you would • When navigating through an automated system such speak to a person sitting a few feet/meters away from as voice mail, or when sending a page, at the end of you.
  • Page 106 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In a convertible vehicle, system performance may be • Echo at the far end can sometimes be reduced by compromised with the convertible top down. lowering the in-vehicle audio volume. • In a convertible vehicle, system performance may be Far End Audio Performance compromised with the convertible top down.
  • Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 I n f o r m a t i o n P r o v i d e d b y :...
  • Page 108 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE I n f o r m a t i o n P r o v i d e d b y :...
  • Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 I n f o r m a t i o n P r o v i d e d b y :...
  • Page 110 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
  • Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
  • Page 112: General Information

    110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information VOICE RECOGNITION SYSTEM (VR) — IF This device complies with Part 15 of the FCC rules and EQUIPPED RSS 210 of Industry Canada. Operation is subject to the Voice Recognition System (VR) Operation following conditions: This Voice Recognition system allows you to •...
  • Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 When you press the VR button, you will hear a beep. The These commands are universal and can be used from any beep is your signal to give a command. menu. All other commands can be used depending upon the active application.
  • Page 114: Commands

    112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Commands In this mode, you can say the following commands: The Voice Recognition system understands two types of • “Radio” (to switch to the radio mode) commands. Universal commands are available at all •...
  • Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 • “Previous Channel” (to select the previous channel) Radio FM To switch to the FM band say “FM” or “Radio FM”. In • “List Channel” (to hear a list of available channels) this mode, you may say the following commands: •...
  • Page 116 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Memo − “Previous” (to play the previous memo) To switch to the voice recorder mode say “Memo”. In this − “Delete” (to delete a memo) mode, you may say the following commands: • “Delete All” (to delete all memos) •...
  • Page 117: Voice Training

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 NOTE: Keep in mind that you have to press the VR SEATS button first and wait for the beep before speaking the Front Manual Seat Adjustment “Barge In” commands. Move the seat forward or rearward using the adjustment Voice Training bar.
  • Page 118: Front Seat Adjustment - Recline

    116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline WARNING! (Continued) To adjust the seatback, lift the lever located on the • Do not allow people to ride in any area of your outboard side of the seat, lean back, and release the lever vehicle that is not equipped with seats and seat at the desired position.
  • Page 119: Eight-Way Driver's Power Seat

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Manual Lumbar Control Power Seat Switches Eight-Way Driver’s Power Seat Four-Way Passenger’s Power Seat — If Equipped The driver’s power seat switches are located on the The front passenger’s power seat switches are located on outboard side of the driver’s seat lower side trim.
  • Page 120: Head Restraints

    118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The four-way seat does not have an up/down adjustment. Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Adjustable head restraints should be adjusted so that the upper edge is as High as practical.
  • Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 After turning the ignition ON, you can choose from a two to one, indicating the change. The Low-level setting High or Low heat setting. Illuminated LEDs on each will turn Off automatically after approximately 30 min- switch indicate the level of heat in use.
  • Page 122: Rear Heated Seats - If Equipped

    120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! (Continued) • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. To avoid heated seat surfaces coming in contact with each other and potential seat overheating, ALWAYS ensure that the seat heater is in the Off position (amber lights indicate High/Low/Off) before plac-...
  • Page 123 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 When the High-level setting is selected, the heater will WARNING! provide a boosted heat level during the first four minutes • Persons who are unable to feel pain to the skin of operation. Then, the heat output will drop to the normal High-level.
  • Page 124: 60/40 Split Rear Seat

    122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 60/40 Split Rear Seat To Lower Rear Seat Either side of the rear seat can be lowered to allow for extended cargo space and still maintain some rear seating room. NOTE: Be sure that the front seats are fully upright and positioned forward.
  • Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 WARNING! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion. They could be seriously injured in an accident.
  • Page 126: Driver Memory Seat - If Equipped

    124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage (Rear Seat Armrest) — If Equipped The rear seat may be equipped with a center storage armrest. Armrest Storage Latch DRIVER MEMORY SEAT — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, Rear Seat Armrest driver’s outside mirror, adjustable brake and accelerator...
  • Page 127: Setting Memory Positions And Linking Remote Keyless Entry (Rke) Transmitter To Memory

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Keyless Entry (RKE) transmitters can also be pro- position. The memory system can accommodate up to grammed to recall the same positions when the UN- four RKE transmitters, each one linked to either of the LOCK button is pressed.
  • Page 128: Memory Position Recall

    126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Adjust the brake and accelerator pedals to the desired 11. Select Remote Linked to Memory in the Electronic positions. Vehicle Information Center (EVIC) and enter Yes . Refer to “Electronic Vehicle Information Center (EVIC) — 5.
  • Page 129: To Disable A Rke Transmitter Linked To Memory

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 To recall the memory setting for driver two, press 3. Press and release the memory S (SET) button located memory button number 2 on the driver’s door, or the on the driver’s door. UNLOCK button on the RKE transmitter linked to 4.
  • Page 130: Easy Entry/Exit Seat

    128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Easy Entry/Exit Seat driving position when the key is placed into the This feature provides automatic driver’s seat positioning ignition, and turned out of the LOCK position toward which will enhance driver mobility out of and into the the ACC/ON position.
  • Page 131: To Open And Close The Hood

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. 1. Pull the release lever located below the instrument panel and in front of the driver’s door. Safety Latch Location CAUTION! To prevent possible damage, do not slam the hood to close it.
  • Page 132: Lights

    130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights and Parking Lights WARNING! Turn the end of the multifunction lever to the first detent for parking light operation. Turn to the second detent for If the hood is not fully latched, it could fly up when headlight operation.
  • Page 133: Automatic Headlight System - If Equipped

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Automatic Headlight System — If Equipped If your vehicle is equipped with a “Rain Sensitive Wiper Turn the end of the multifunction lever to the third detent System” and it is activated, the headlights will automati- to activate the automatic headlight system.
  • Page 134: Smartbeams - If Equipped

    132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SmartBeams — If Equipped To Activate The SmartBeam system provides increased forward light- 1. Select “Auto Headlamp Low/High Beams? — Low/ ing at night by automating high beam control through High Beam.” Refer to “EVIC — Customer-Programmable the use of a digital camera mounted on the inside Features”...
  • Page 135: Daytime Running Lights - If Equipped

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 To Deactivate Daytime Running Lights — If Equipped The high beam headlights come on at a low intensity 1. Pull back on the multifunction lever to manually level whenever the engine is running, and the transmis- deactivate the system (normal operation of low beams).
  • Page 136: Instrument Panel And Interior Lights

    134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Instrument Panel and Interior Lights When the multifunction lever is in the parking light, headlight, or AUTO position (if equipped), rotating the center portion of the lever up and down will increase and decrease the brightness (dimmer control) of the instru- ment panel lights.
  • Page 137: Battery Saver Feature

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Battery Saver Feature turn lights, low beam headlights, or Auto headlights and If the multifunction lever is left in the interior light pull out the end of the multifunction lever. A light in the position, parking light position, or the headlight position instrument cluster shows when the fog lights are on.
  • Page 138: Turn Signals

    136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: • Turning on the high beam headlights turns off the fog lights. • A front fog light is a lighting device that provides illumination in front of the vehicle under conditions of fog, rain, snow, or dust.
  • Page 139: High Beam Switch

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 High Beam Switch Flash-to-Pass Push the multifunction lever away from you to switch You can signal another vehicle by lightly pulling the the headlights to high beam. Pull the multifunction lever multifunction lever toward the steering wheel. This will towards you to switch the headlights back to low beam.
  • Page 140: Front Map/Reading Lights

    138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE contains both driver and passenger reading lights), read- ing lights (located above the rear doors), and a rear cargo light. Opening a door, pressing the UNLOCK button on the Remote Keyless Entry (RKE) transmitter or turning the center of the multifunction control lever to the extreme up position, will activate all interior courtesy lights.
  • Page 141: Windshield Wipers And Washers

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 WINDSHIELD WIPERS AND WASHERS The front and rear wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select Low, High, or one of the five speed sensitive intermittent windshield wiper speeds.
  • Page 142: Mist

    140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold Mist while spray is desired. If the lever is pulled while in the Use the Mist feature when weather conditions make delay range, the wiper will operate for several seconds occasional usage of the wipers necessary.
  • Page 143: Rain Sensing Wipers - If Equipped

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 • The rain sensing feature may not function properly Rain Sensing Wipers — If Equipped This feature senses moisture on the windshield and when ice, or dried salt water is present on the wind- automatically activates the wipers for the driver.
  • Page 144: Tilt/Telescoping Steering Column

    142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside tem- perature is greater than 32°F (0°C). • Transmission in NEUTRAL Position — When the ignition is ON, and the transmission is in the NEU- TRAL position, the rain sensing system will not oper- ate until the wiper switch is moved, vehicle speed is...
  • Page 145: Adjustable Pedals - If Equipped

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 the steering wheel outward or push it inward as desired. adjusted without compromising safety or comfort in To lock the steering column in position, push the control actuating the pedals. handle upward until fully engaged. WARNING! Do not adjust the steering wheel while driving.
  • Page 146: Electronic Speed Control - If Equipped

    144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the top of the switch to move the pedals rearward CAUTION! (toward the driver). Do not place any article under the adjustable pedal’s • The pedals can be adjusted with the ignition OFF. or impede its ability to move as it may cause damage •...
  • Page 147: To Activate

    UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous. You could accidentally set the system or cause it to go faster than you want. You could lose control and have an accident. Always leave the system OFF when you are not using it.
  • Page 148 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Speed Control without erasing the set speed memory. that tapping the lever three times will increase speed by Pressing the ON/OFF button or turning the ignition 3 mph (5 km/h) (3.7L, 4.7L, 5.7L, and 3.0L diesel en- switch OFF erases the set speed memory.
  • Page 149 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 To Accelerate For Passing Section and Note Section for limitations of this system Press the accelerator as you would normally. When the and recommendations. pedal is released, the vehicle will return to the set speed. The Rear Park Assist will remember the last system state Using Electronic Speed Control On Hills (enabled or disabled) from the last ignition cycle when...
  • Page 150 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The sensors can detect obstacles from approximately 12 to 59 in (30 to 150 cm) from the rear fascia in the horizontal direction, depending on the location and orientation of the obstacle and the type of obstacle. Rear Park Assist Warning Display The Rear Park Assist Warning Display, located in the headliner near the flipper glass, provides both visible and...
  • Page 151 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 The system dimly illuminates the two outer most yellow LEDs when it is ON and detecting no obstacles. The following chart shows the warning display operation when the system is detecting an obstacle: WARNING DISPLAY DISTANCES DISPLAY LED OBSTACLE DISTANCE FROM:...
  • Page 152 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enable/Disable The Rear Park Assist When the switch is pressed to disable the system, the The Rear Park Assist can be enabled and disabled with a instrument cluster will display the “PARK ASSIST DIS- switch located on the upper switch bank of the instru- ABLED”...
  • Page 153 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Cleaning The Rear Park Assist WARNING! Clean the Rear Park Assist Sensors with water, car wash soap and a soft cloth. Do not use rough or hard cloths. Do Drivers must be careful when backing up even when not scratch or poke the sensors.
  • Page 154 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4. Enable or disable the rear camera feature by selecting CAUTION! (Continued) enable rear camera in reverse soft key. • To avoid vehicle damage, the vehicle must be 5. Press the “save” soft key. driven slowly when using the Rear Camera system to be able to stop in time when an obstacle is seen.
  • Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 4. When the vehicle is shifted into REVERSE, an image of the rear of the vehicle will appear with a caution note to check entire surroundings displayed across the top of the screen. After five seconds this note will disappear. 5.
  • Page 156 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lights also turn on when a front door or rear door is The HomeLink buttons are located in the overhead opened. The lights will also turn on when the UNLOCK console, and contain one, two, or three dots/lines desig- button on the remote keyless entry transmitter is pressed.
  • Page 157 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Programming HomeLink WARNING! Before You Begin • Your motorized door or gate will open and close If you have not trained any of the HomeLink buttons, while you are training the Universal Transceiver. erase all channels before you begin training.
  • Page 158 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) NOTE: Some gate operators and garage door openers from the HomeLink buttons while keeping the EVIC may require you to replace Step 3 with procedures noted display in view.
  • Page 159 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 This can usually be found where the hanging antenna 6. Firmly press and release the “learn” or “training” wire is attached to the garage door opener motor (it is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer.
  • Page 160 158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Gate Operator/Canadian Programming has successfully accepted the frequency signal. The Canadian radio-frequency laws require transmitter sig- EVIC display will change from “CHANNEL # TRAIN- nals to “time-out” (or quit) after several seconds of ING”...
  • Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Reprogramming A Single HomeLink Button The HomeLink Universal Transceiver is disabled when To reprogram a channel that has been previously trained, the Vehicle Security Alarm is active. follow these steps: Troubleshooting Tips 1. Turn the ignition switch to the ON/RUN position. If you are having trouble programming HomeLink , here are some of the most common solutions: 2.
  • Page 162 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information POWER SUNROOF — IF EQUIPPED This device complies with FCC rules Part 15 and Industry The power sunroof switch is located between the sun Canada RSS-210. Operation is subject to the following visors on the overhead console.
  • Page 163 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Opening Sunroof — Express WARNING! Press the switch rearward and release, and the sunroof • Never leave children in a vehicle, with the key in will open automatically from any position. The sunroof will open fully, then stop automatically.
  • Page 164 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Override NOTE: The sunshade cannot be closed if the sunroof is If a known obstruction (ice, debris, etc.) prevents closing open. the sunroof, press the switch forward and hold for two Wind Buffeting seconds after the reversal occurs.
  • Page 165 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Ignition Off Operation The power sunroof switches remain active for up to 10 minutes after the ignition switch has been turned OFF. Opening either front door will cancel this feature. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed.
  • Page 166 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Do not use a three-prong adapter. power from the vehicle’s battery, even when not in •...
  • Page 167 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 POWER INVERTER — IF EQUIPPED This outlet can power cellular phones, electronics and There is a 115-Volt, 150-Watt inverter outlet located on the other low power devices requiring power up to 150 back of the center console to convert DC current to AC Watts.
  • Page 168 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the power inverter switch (located on the upper NOTE: • When the power inverter switch is pressed, there will switch bank) to turn the power on to the outlet. Press the switch again to turn the power off. be a delay of approximately one second before the inverter status indicator turns ON.
  • Page 169 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 CUPHOLDERS In the center console, there are two cupholders for the front seat passengers. Rear Cupholders CARGO AREA FEATURES Cargo Light Front Cupholders The cargo area light is activated by opening the liftgate, The rear passengers have access to two cupholders that opening any door, or by rotating the dimmer control on pull out from the lower center of the rear seat.
  • Page 170 168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the cargo light lens surface will turn off all interior lamps. Retractable Cargo Area Cover — If Equipped Push on the lens surface a second time to restore the NOTE: The purpose of this cover is for privacy, not to interior lights to normal operation.
  • Page 171 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 WARNING! In an accident, a loose cargo cover in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle. Do not store the cargo cover on the cargo floor or in the passenger compartment.
  • Page 172 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cargo Tie-Down Hooks WARNING! The tie-downs located on the cargo area floor should be • To help protect against personal injury, passengers used to safely secure loads when the vehicle is moving. should not be seated in the rear cargo area. The rear cargo space is intended for load carrying purposes only, not for passengers, who should sit in seats and use seat belts.
  • Page 173 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Cargo Load Floor WARNING! (Continued) The panel in the load floor is reversible for added utility. • Do not carry loads which exceed the load limits One side is carpeted and the other side features a plastic described on the label attached to the left door or lined tray which holds a variety of items.
  • Page 174 172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cargo load floor is held by spring loaded latches. In REAR WINDOW FEATURES order to use the cargo load floor, use the following Rear Window Wiper/Washer procedure: A switch on the right side of the steering column controls NOTE: The cargo load floor latches should not be operation of the rear wiper/washer function.
  • Page 175 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 If the liftgate flipper glass is open, connection to the rear window wiper is interrupted preventing activation of the rear wiper blade. When the liftgate flipper glass is closed, the rear wiper switch, or the ignition switch, needs to be turned OFF and ON to restart the rear wiper.
  • Page 176 174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Distribute cargo weight evenly on the roof rack crossbars. CAUTION! The roof rack does not increase the total load carrying • To avoid damaging the electrical conductors of the capacity of the vehicle. Be sure the total load of cargo inside the vehicle plus that on the external rack does not rear window defroster, do not use scrapers, sharp exceed the maximum vehicle load capacity.
  • Page 177 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 NOTE: CAUTION! • To help control wind noise when the crossbars are not • To prevent damage to the roof of your vehicle, DO in use, place the front crossbar in the second detent from the front of the vehicle and the rear crossbar in NOT carry any loads on the roof rack without the last detent closest to the rear of the vehicle.
  • Page 178 176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) WARNING! • Travel at reduced speeds and turn corners care- Cargo must be securely tied before driving your fully when carrying large or heavy loads on the vehicle. Improperly secured loads can fly off the roof rack.
  • Page 179: Understanding Your Instrument Panel

    UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....181 Compass Display ....200 Instrument Cluster –...
  • Page 180 178 UNDERSTANDING YOUR INSTRUMENT PANEL Notes On Playing MP3/WMA Files ..218 Operation Instructions — CD Mode For CD And MP3 Audio Play ....229 List Button (Disc Mode For MP3/WMA Play) .
  • Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 179 Universal Consumer Interface (UCI) — If Selecting uconnect studios (Satellite) Equipped ......247 Mode .
  • Page 182 180 UNDERSTANDING YOUR INSTRUMENT PANEL CD Player ......259 Automatic Temperature Control — If Equipped ......264 CD/DVD Maintenance .
  • Page 183: Instrument Panel Features

    UNDERSTANDING YOUR INSTRUMENT PANEL 181 INSTRUMENT PANEL FEATURES 1 - Air Outlet 5 - Upper Switch Bank 9 - Lower Switch Bank 2 - Instrument Cluster 6 - Power Outlet/Cigar Lighter 10 - Climate Controls 3 - Radio 7 - Storage Bin 11 - Ignition Switch 4 - Glove Compartment 8 - Power Outlet...
  • Page 184: Instrument Cluster - Gasoline Engine

    182 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER – GASOLINE ENGINE I n f o r m a t i o n P r o v i d e d b y :...
  • Page 185: Instrument Cluster - Diesel Engine

    UNDERSTANDING YOUR INSTRUMENT PANEL 183 INSTRUMENT CLUSTER – DIESEL ENGINE I n f o r m a t i o n P r o v i d e d b y :...
  • Page 186: Instrument Cluster Description

    184 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION the brake booster, the ABS pump will run when applying the brake and a brake pedal pulsation may be felt during 1. Speedometer each stop. Indicates vehicle speed. The dual brake system provides a reserve braking capac- 2.
  • Page 187 UNDERSTANDING YOUR INSTRUMENT PANEL 185 The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON position. Driving a vehicle with the red brake light on is NOTE: This light shows only that the parking brake is dangerous.
  • Page 188 186 UNDERSTANDING YOUR INSTRUMENT PANEL the ON position before engine start. If the bulb does not during starting, stays on, or turns on while driving, have come on when turning the key from OFF to ON, have the the system inspected by an authorized dealer as soon as condition checked promptly.
  • Page 189 UNDERSTANDING YOUR INSTRUMENT PANEL 187 8. Tachometer Do not operate the vehicle until the cause is corrected. Indicates the engine speed in revolutions per minute This light does not show how much oil is in the engine. (RPM). The engine oil level must be checked under the hood. 9.
  • Page 190 188 UNDERSTANDING YOUR INSTRUMENT PANEL vehicle placard or tire inflation pressure label, you should maintain correct tire pressure, even if under-inflation has determine the proper tire inflation pressure for those not reached the level to trigger illumination of the TPMS tires.) low tire pressure telltale.
  • Page 191 UNDERSTANDING YOUR INSTRUMENT PANEL 189 tires or wheels on your vehicle, to ensure that the 13. Temperature Gauge replacement or alternate tires and wheels allow the TPMS The temperature gauge shows engine coolant tempera- to continue to function properly. ture. Any reading within the normal range indicates that the engine cooling system is operating satisfactorily.
  • Page 192 190 UNDERSTANDING YOUR INSTRUMENT PANEL 15. TOW/HAUL Indicator Light — If Equipped WARNING! This light will illuminate when the TOW/ HAUL button has been selected. The TOW/ A hot engine cooling system is dangerous. You or HAUL button is located in the center of the others could be badly burned by steam or boiling instrument panel (below the climate controls).
  • Page 193 UNDERSTANDING YOUR INSTRUMENT PANEL 191 17. 4WD LOW Indicator — If Equipped 19. Cruise Indicator This light alerts the driver that the vehicle is in This indicator lights when the speed control the 4WD LOW mode. The front and rear drive- system is turned ON.
  • Page 194 192 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: You must apply the brakes before shifting from stall and your vehicle may require towing. The light will PARK. come on when the ignition is first turned on and remain on briefly as a bulb check. If the light does not come on 22.
  • Page 195: Electronic Vehicle Information Center (Evic)

    UNDERSTANDING YOUR INSTRUMENT PANEL 193 vehicle is experiencing a problem with the charging ELECTRONIC VEHICLE INFORMATION CENTER system. Obtain SERVICE IMMEDIATELY. See an autho- (EVIC) rized dealer. The Electronic Vehicle Information Center (EVIC) fea- tures a driver-interactive display that is located in the 26.
  • Page 196 194 UNDERSTANDING YOUR INSTRUMENT PANEL • Vehicle Information Warning Message Displays FUNCTION SELECT Button Press the FUNCTION SELECT button to select • Personal Settings (Customer-Programmable Features) the displayed function YES (Y) or NO (N). • Compass Display • Outside Temperature Display SCROLL Button •...
  • Page 197: Electronic Vehicle Information Center (Evic) Displays

    UNDERSTANDING YOUR INSTRUMENT PANEL 195 • PROGRAMMING ACTIVE — NEW KEY PRO- Electronic Vehicle Information Center (EVIC) Displays GRAMMED When the appropriate conditions exist, the Electronic • SERVICE SECURITY KEY Vehicle Information Center (EVIC) displays the following • DRIVER/PASSENGER DOOR OPEN (with graphic) messages: •...
  • Page 198 196 UNDERSTANDING YOUR INSTRUMENT PANEL • LIFTGATE/HOOD OPEN (with graphic) • AUTO HIGH BEAMS ON • HOOD/GLASS/DOOR OPEN (with graphic) • AUTO HIGH BEAMS OFF • HOOD/GLASS/DOORS OPEN (with graphic) • PARK ASSIST DISABLED • HOOD/GATE/DOOR OPEN (with graphic) • SERVICE SUSPENSION •...
  • Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL 197 • IOD FUSE OUT • LEFT FRONT LOW PRESSURE (Premium TPM Sys- tem Only) • HILL DESCENT CONTROL • RIGHT FRONT LOW PRESSURE (Premium TPM Sys- • MEMORY #1 POSITIONS SET tem Only) • MEMORY #2 POSITIONS SET •...
  • Page 200: Engine Oil Change Indicator System

    198 UNDERSTANDING YOUR INSTRUMENT PANEL • PRESS BRAKE TO START release the MENU button. To reset the oil change indica- tor system (after performing the scheduled maintenance) • INSERT KEY refer to the following procedure. • TURN TO ON 1. Turn the ignition switch to the ON position (Do not Engine Oil Change Indicator System start the engine).
  • Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 199 • Trip A Distance To Empty (DTE) Shows the estimated distance that can be traveled with • Trip B the fuel remaining in the tank. This estimated distance is • Elapsed Time determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel •...
  • Page 202: Compass Display

    200 UNDERSTANDING YOUR INSTRUMENT PANEL Trip A button once to clear the resettable function being dis- Shows the total distance traveled for Trip A since the last played. To reset all resettable functions, press and hold reset. the FUNCTION SELECT button for two seconds. Current display will reset along with other functions Trip B Shows the total distance traveled for Trip B since the last...
  • Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 201 Manual Compass Calibration Compass Variance If the compass appears erratic and the “CAL” indicator Compass Variance is the difference between magnetic does not appear in the EVIC display, you must put the North and Geographic North. In some areas of the compass into the Calibration Mode manually, as follows: country, the difference between magnetic and geographic North is great enough to cause the compass to give false...
  • Page 204: Personal Settings (Customer-Programmable Features)

    202 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Press and release the FUNCTION SELECT button to change the variance number. Continue until desired number is reached. 5. Press either MENU, SCROLL, or COMPASS/TEMP button to set the value and exit. Personal Settings (Customer-Programmable Features) Personal Settings allows the driver to set and recall features when the transmission is in PARK.
  • Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 203 FUNCTION SELECT button while in this display to opened. To make your selection, press and release the select English, Espanol, or Francais. Then, as you con- FUNCTION SELECT button until YES (Y) or NO (N) tinue, the information will display in the selected lan- appears.
  • Page 206 204 UNDERSTANDING YOUR INSTRUMENT PANEL feature may be selected with or without the “Flash Automatic High Beams (Available with SmartBeam Lamps with Lock” feature. To make your selection, press Only) and release the FUNCTION SELECT button until YES (Y) When this feature is selected, the high beam headlights or NO (N) appears.
  • Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 205 NOTE: Turning the headlights on during the daytime Reset Service Distance (Displays Only if Service causes the instrument panel lights to dim. To increase the Interval was Changed) brightness, refer to “Lights” in Section 3 of this manual. When this feature is selected, the current accumulated service distance can be reset to the newly selected service Rain Sensing Intermittent Wipers —...
  • Page 208: System Status

    206 UNDERSTANDING YOUR INSTRUMENT PANEL door. Refer to “Easy Entry/Exit Seat” under “Driver Hill Start Assist Memory Seat” in Section 3 of this manual for more To make your selection, press and release the FUNC- information. TION SELECT button until YES (Y) or NO (N) appears. Key Off Power Delay Display Units of Measure In: When this feature is selected, the power window...
  • Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 207 • Tire Pressure Monitor System (shows the current pres- NOTE: • Tires heat up during normal driving conditions. Heat sure of all four road tires.) For additional information, refer to “Tire Pressure Monitor System” in Section 5 of will cause the tire pressure to increase from 2 to 6 psi this manual.
  • Page 210: Sales Code Req - Am/Fm Stereo Radio And 6-Disc Cd/Dvd Changer (Mp3/Wma Aux Jack)

    208 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE REQ — AM/FM STEREO RADIO Operating Instructions - Radio Mode AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX NOTE: The ignition switch must be in the ON or ACC JACK) position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
  • Page 211 UNDERSTANDING YOUR INSTRUMENT PANEL 209 to seek up and the left switch to seek down. The radio Phone Button uconnect phone — If Equipped will remain tuned to the new station until you make Press this button to operate the uconnect phone feature another selection.
  • Page 212 210 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Adjust the minutes using the right side TUNE/ TUNE Control SCROLL control knob. Press the TUNE/SCROLL control Turn the rotary TUNE/SCROLL control knob clockwise knob to save the time change. to increase or counterclockwise to decrease the frequency. 5.
  • Page 213 UNDERSTANDING YOUR INSTRUMENT PANEL 211 SCROLL control knob to the right or left to adjust the Toggle the MUSIC TYPE button to select the following sound level from the right or left side speakers. format types: 16-Digit Character Push the rotary TUNE/SCROLL control knob a fifth time Program Type Display and FADE will display.
  • Page 214 212 UNDERSTANDING YOUR INSTRUMENT PANEL station with the same selected Music Type name. The 16-Digit Character Program Type Music Type function only operates when in the FM Display mode. Personality Persnlty Public Public If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be Rhythm and Blues R &...
  • Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL 213 • DISC Play/Pause - You can toggle between NOTE: • The available selections for each of the above entries playing the DVD and pausing the DVD by pushing the SELECT button (if equipped). varies depending upon the disc. •...
  • Page 216 214 UNDERSTANDING YOUR INSTRUMENT PANEL TUNE/SCROLL control knob to adjust the minutes. down and selecting other. Enter the country code using Press the TUNE/SCROLL control knob again to save the TUNE/SCROLL control knob to scroll up and down changes. to select the number and then push to select. •...
  • Page 217 UNDERSTANDING YOUR INSTRUMENT PANEL 215 Aspect Ratio — If Equipped SET Button — To Set the Pushbutton Memory Selecting this item allows you to choose between wide When you are receiving a station that you wish to screen, pan scan, and letter box. commit to pushbutton memory, press the SET button.
  • Page 218: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)

    216 UNDERSTANDING YOUR INSTRUMENT PANEL Every time a preset button is used, a corresponding CAUTION! button number will display. The radio may shut down during extremely hot Buttons 1 - 6 conditions. When this occurs, the radio will indicate These buttons tune the radio to the stations that you “Disc Hot”...
  • Page 219 UNDERSTANDING YOUR INSTRUMENT PANEL 217 Radio display will show LOADING DISC when the disc The disc can be ejected with the radio and ignition OFF. is loading and “READING DISC” when the radio is SEEK Button (CD MODE) reading the disc. Press the right SEEK button for the next selection on the CD.
  • Page 220: Notes On Playing Mp3/Wma Files

    218 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF (CD MODE) Supported Medium Formats (File Systems) Press and hold FF (Fast Forward) and the CD player will The medium formats supported by the radio are ISO 9660 begin to fast forward until FF is released, or RW or Level 1 and Level 2 and includes the Joliet extension.
  • Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL 219 Multisession disc formats are supported by the radio. frequencies in the following table are supported. In Multisession discs may contain combinations of normal addition, variable bit rates (VBR) are also supported. The CD audio tracks and computer files (including MP3/ majority of MP3/WMA files use a 44.1 kHz sampling rate WMA files).
  • Page 222: List Button (Disc Mode For Mp3/Wma Play)

    220 UNDERSTANDING YOUR INSTRUMENT PANEL • Number of files and folders - Loading times will ID3 Tag information for artist, song title, and album title are supported for ID3 version 1 tags. ID3 version 2 is not increase with more files and folders supported by the radios.
  • Page 223: Info Button (Disc Mode For Mp3/Wma Play)

    UNDERSTANDING YOUR INSTRUMENT PANEL 221 INFO Button (DISC Mode for MP3/WMA Play) Pressing the AUX button will change the mode to auxil- Pressing the INFO button repeatedly will scroll through iary device if the AUX jack is connected. the following TAG information: Song Title, Artist, File NOTE: The AUX device must be turned on and the Name, and Folder Name (if available).
  • Page 224: Operating Instructions - Voice Recognition

    222 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Operating Instructions - uconnect studios Press the TIME button to change the display from (Satellite Radio) (If Equipped) elapsed playing time to time of day. The time of day will Refer to “uconnect studios (Satellite Radio)”...
  • Page 225: Equipped

    UNDERSTANDING YOUR INSTRUMENT PANEL 223 intended for home and other limited viewing uses only, Refer to your uconnect tunes (REN) or (RER) user’s unless otherwise authorized by Macrovision. Reverse manual for detailed operating instructions. engineering or disassembly is prohibited. Operating Instructions — Voice Recognition DTS™...
  • Page 226 224 UNDERSTANDING YOUR INSTRUMENT PANEL To Manually Set the Clock — RER/REN 6. To save the new time setting, touch the screen where the word “Save” is displayed. 1. Turn on the radio. Changing Daylight Savings Time 2. Touch the screen where the time is displayed. When selected, this feature will display the time of day in 3.
  • Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 225 Show Time if Radio is Off Changing the Time Zone When selected, this feature will display the time of day 1. Turn on the radio. on the touch screen when the radio is turned off. Proceed as follows to change the current setting: 2.
  • Page 228: Sales Code Res - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack)

    226 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RES — AM/FM STEREO RADIO Operating Instructions — Radio Mode WITH CD PLAYER (MP3 AUX JACK) NOTE: The ignition switch must be in the ON or ACC NOTE: The radio sales code is located on the lower right position to operate the radio.
  • Page 229 UNDERSTANDING YOUR INSTRUMENT PANEL 227 SEEK Buttons 4. Adjust the minutes using the right side TUNE/ Press and release the SEEK buttons to search for the next SCROLL control knob. Press the TUNE/SCROLL control listenable station in AM/FM mode. Press the right switch knob to save time change.
  • Page 230 228 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade. control knob to the right or left to increase or decrease the AM/FM Button mid-range tones.
  • Page 231: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play

    UNDERSTANDING YOUR INSTRUMENT PANEL 229 SET 2 in both AM and FM. This allows a total of 12 AM Operation Instructions — CD MODE For CD And and 12 FM stations to be stored into pushbutton memory. MP3 Audio Play The stations stored in SET 2 memory can be selected by NOTE: pressing the pushbutton twice.
  • Page 232 230 UNDERSTANDING YOUR INSTRUMENT PANEL If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD. begin to play when you insert the disc.
  • Page 233: Notes On Playing Mp3 Files

    UNDERSTANDING YOUR INSTRUMENT PANEL 231 the current selection. Pressing and holding the SEEK SET/RND Button (Random Play Button) button will allow faster scrolling through the tracks in Press this button while the CD is playing to activate CD and MP3 modes. Random Play.
  • Page 234 232 UNDERSTANDING YOUR INSTRUMENT PANEL Supported Medium Formats (File Systems) exceeding 20 folders will result in this display. With The medium formats supported by the radio are ISO 9660 200 files, exceeding 50 folders will result in this Level 1 and Level 2 and includes the Joliet extension. display.) When reading discs recorded using formats other than •...
  • Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 233 Supported MP3 File Formats MPEG Sampling Bit Rate (kbps) The radio will recognize only files with the *.MP3 exten- Specification Frequency (kHz) sion as MP3 files. Non-MP3 files named with the *.MP3 160, 128, 144, extension may cause playback problems.
  • Page 236: Operation Instructions - Auxiliary Mode

    234 UNDERSTANDING YOUR INSTRUMENT PANEL Loading times for playback of MP3 files may be affected MP3 player, or cassette player, and utilize the vehicle’s by the following: audio system to amplify the source and play through the vehicle speakers. • Media - CD-RW media may take longer to load than CD-R media Pressing the DISC/AUX button will change the mode to auxiliary device if the AUX jack is connected.
  • Page 237: Sales Code Res/Rsc - Am/Fm Stereo Radio With Cd Player (Mp3 Aux Jack) And Sirius Radio

    UNDERSTANDING YOUR INSTRUMENT PANEL 235 SALES CODE RES/RSC — AM/FM STEREO Operating Instructions — Radio Mode RADIO WITH CD PLAYER (MP3 AUX JACK) AND NOTE: The ignition switch must be in the ON or ACC SIRIUS RADIO position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
  • Page 238 236 UNDERSTANDING YOUR INSTRUMENT PANEL to seek up and the left switch to seek down. The radio If your vehicle is not equipped with or this feature is not will remain tuned to the new station until you make available on your vehicle, a “Not Equipped With another selection.
  • Page 239 UNDERSTANDING YOUR INSTRUMENT PANEL 237 5. To exit, press any button/knob or wait five seconds. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise The clock can also be set by pressing the SETUP button. to increase or counterclockwise to decrease the frequency. For vehicles equipped with satellite radio, press the SETUP button, use the TUNE/SCROLL control to select Setting the Tone, Balance, and Fade...
  • Page 240 238 UNDERSTANDING YOUR INSTRUMENT PANEL SCROLL control knob to the right or left to adjust the Toggle the MUSIC TYPE button to select the following sound level from the right or left side speakers. format types: 16-Digit Character Push the rotary TUNE/SCROLL control knob a fifth time Program Type Display and FADE will display.
  • Page 241 UNDERSTANDING YOUR INSTRUMENT PANEL 239 By pressing the SEEK button when the Music Type icon 16-Digit Character Program Type is displayed, the radio will be tuned to the next frequency Display station with the same selected Music Type name. The Personality Persnlty Music Type function only operates when in the FM...
  • Page 242 240 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button and 12 FM stations to be stored into pushbutton memory. Press the button to select either AM or FM mode. The stations stored in SET 2 memory can be selected by pressing the pushbutton twice. SET/RND Button —...
  • Page 243: Operation Instructions - Cd Mode For Cd And Mp3 Audio Play

    UNDERSTANDING YOUR INSTRUMENT PANEL 241 Operation Instructions — CD MODE for CD and If you insert a disc with the ignition ON and the radio MP3 Audio Play ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and •...
  • Page 244 242 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD the current selection. Pressing and holding the SEEK Press the EJECT button to eject the CD. button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within...
  • Page 245: Notes On Playing Mp3 Files

    UNDERSTANDING YOUR INSTRUMENT PANEL 243 SET/RND Button (Random Play Button) Supported Medium Formats (File Systems) Press this button while the CD is playing to activate The medium formats supported by the radio are ISO 9660 Random Play. This feature plays the selections on the Level 1 and Level 2 and includes the Joliet extension.
  • Page 246 244 UNDERSTANDING YOUR INSTRUMENT PANEL exceeding 20 folders will result in this display. With Supported MP3 File Formats 200 files, exceeding 50 folders will result in this The radio will recognize only files with the *.MP3 exten- display.) sion as MP3 files. Non-MP3 files named with the *.MP3 extension may cause playback problems.
  • Page 247: List Button (Cd Mode For Mp3 Play)

    UNDERSTANDING YOUR INSTRUMENT PANEL 245 Loading times for playback of MP3 files may be affected MPEG Sampling Bit Rate (kbps) by the following: Specification Frequency (kHz) 160, 128, 144, • Media - CD-RW media may take longer to load than MPEG-2 Audio 112, 96, 80, 64, CD-R media...
  • Page 248: Info Button (Cd Mode For Mp3 Play)

    246 UNDERSTANDING YOUR INSTRUMENT PANEL begin playing the files contained in that folder (or the Operation Instructions - Auxiliary Mode next folder in sequence if the selection does not contain The auxiliary (AUX) jack is an audio input jack which playable files).
  • Page 249: Universal Consumer Interface (Uci) - If Equipped

    UNDERSTANDING YOUR INSTRUMENT PANEL 247 Operating Instructions - uconnect phone (If This feature allows you to plug an iPod into the Equipped) vehicle’s sound system through a 16–pin connector using Refer to “uconnect phone” in Section 3. the provided interface cable. Operating Instructions - uconnect studios UCI supports Mini, 4G, Photo, Nano, 5G iPod (Satellite Radio) (If Equipped)
  • Page 250: Connecting The Ipod

    248 UNDERSTANDING YOUR INSTRUMENT PANEL Connecting The iPod Using This Feature Use the optional connection cable to connect an iPod to By using the optional connection cable to connect an the vehicle’s 16–pin connector port (which is located in iPod to the vehicle’s UCI 16–pin connector port: the glove compartment on some vehicles).
  • Page 251: Play Mode

    UNDERSTANDING YOUR INSTRUMENT PANEL 249 • Jump backward in the current track by pressing and Play Mode When switched to UCI mode, the iPod automatically holding the << RW button. Holding the << RW starts Play mode. In Play mode, you may use the button long enough will take you to the beginning following buttons on the radio faceplate to control the of the current track.
  • Page 252: List Or Browse Mode

    250 UNDERSTANDING YOUR INSTRUMENT PANEL • While a track is playing, press the INFO button to see Shuffle OFF modes for the iPod . If the RND icon is the associated metadata (Artist, track title, album, etc.) showing on the radio display, then the shuffle mode is for that track.
  • Page 253 UNDERSTANDING YOUR INSTRUMENT PANEL 251 • During all List modes, the iPod displays all lists in • To Exit List mode without selecting a track, press the “wrap-around” mode. So if the track is at the same PRESET button again to go back to Play bottom of the list just turn the wheel backwards mode.
  • Page 254: Uconnect Studios (Satellite Radio) - If

    252 UNDERSTANDING YOUR INSTRUMENT PANEL uconnect studios (SATELLITE RADIO) — IF CAUTION! EQUIPPED (REN/REQ/RER/RES RADIOS ONLY) • Leaving the iPod (or any supported device) any- Satellite radio uses direct satellite-to-receiver broadcast- ing technology to provide clear digital sound, coast to where in the vehicle in extreme heat or cold can coast.
  • Page 255: Electronic Serial Number/Sirius Identification Number (Esn/Sid)

    UNDERSTANDING YOUR INSTRUMENT PANEL 253 number 888-539-7474, or visit the Sirius web site at Sirius ID number will display. The Sirius ID number www.sirius.com, or at www.siriuscanada.ca for Cana- display will time out in two minutes. Press any button on dian residents.
  • Page 256: Reception Quality

    254 UNDERSTANDING YOUR INSTRUMENT PANEL bikes should be placed as far rearward as possible, within Operating Instructions - uconnect studios the loading design of the rack. Do not place items directly (Satellite) Mode on or above the antenna. NOTE: The ignition switch must be in the ON or ACC Reception Quality position to operate the radio.
  • Page 257 UNDERSTANDING YOUR INSTRUMENT PANEL 255 INFO Button MUSIC TYPE Button Pressing the INFO button will cycle the display informa- Pressing this button once will turn on the Music Type tion between Artist, Song Title, and Composer (if avail- mode for five seconds. Pressing the MUSIC TYPE button able).
  • Page 258: Operating Instructions - Uconnect Phone (If Equipped)

    256 UNDERSTANDING YOUR INSTRUMENT PANEL SETUP Button You may add a second channel to each pushbutton by Pressing the SETUP button allows you to select the repeating the above procedure with this exception: Press following items: the SET button twice and SET 2 will show in the display window.
  • Page 259: Uconnect Studios (Sirius Backseat Tv™) - If Equipped

    UNDERSTANDING YOUR INSTRUMENT PANEL 257 uconnect studios (SIRIUS BACKSEAT TV™) — powered remote control, and two headsets. Refer to your IF EQUIPPED VES™ User’s Manual for detailed operating instructions. Satellite video uses direct satellite receiver broadcasting The LCD screen is located on the headliner behind the technology to provide streaming video.
  • Page 260: Remote Sound System Controls - If Equipped

    258 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Control Location Remote Sound System Controls (Back View of Steering Wheel) REMOTE SOUND SYSTEM CONTROLS — IF The right-hand control is a rocker-type switch with a EQUIPPED pushbutton in the center and controls the volume and The remote sound system controls are located on the rear mode of the sound system.
  • Page 261: Radio Operation

    UNDERSTANDING YOUR INSTRUMENT PANEL 259 Pressing the center button will make the radio switch CD Player between the various modes available (AM/FM/TAPE/ Pressing the top of the switch once will go to the next CD, Etc.). track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track, or to the The left-hand control is a rocker-type switch with a beginning of the previous track if it is within one second...
  • Page 262: Cd/Dvd Maintenance

    260 UNDERSTANDING YOUR INSTRUMENT PANEL CD/DVD MAINTENANCE NOTE: If you experience difficulty in playing a particu- To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e. scratched, reflective precautions: coating removed, a hair, moisture or dew on the disc) oversized, or have protection encoding.
  • Page 263: Climate Controls

    UNDERSTANDING YOUR INSTRUMENT PANEL 261 CLIMATE CONTROLS Manual Air Conditioning And Heating System — If Equipped The controls for the heating/air conditioning and venti- lation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions.
  • Page 264 262 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Temperature Control The blower control rotary knob (on the The temperature control rotary knob left) controls the blower and can be set (in the center) controls the air tem- to one of four speeds, and OFF. The perature.
  • Page 265 UNDERSTANDING YOUR INSTRUMENT PANEL 263 Defrost through vents under the front seats. Some airflow is Air is directed to the windshield through the delivered to defrost while in the floor mode so that outlets at the base of the windshield. Air is also comfort can be maintained.
  • Page 266: Automatic Temperature Control - If Equipped

    264 UNDERSTANDING YOUR INSTRUMENT PANEL Recirculation Slight changes in engine speed or power may be noticed The recirculation feature can be selected with when the air conditioning compressor is on. This is a the mode control knob. You may choose be- normal occurrence as the compressor will cycle on and tween Bi-Level Recirculation and Panel Recir- off to maintain comfort and increase fuel economy.
  • Page 267 UNDERSTANDING YOUR INSTRUMENT PANEL 265 be used for front seat occupants only. The HI AUTO position should be used when more airflow is desired, or when rear seat occupants are present. Dial in the comfort setting you would like the system to maintain by rotating the driver’s or passenger’s control knob.
  • Page 268 266 UNDERSTANDING YOUR INSTRUMENT PANEL respectively. With the temperature setting in these posi- NOTE: • The surface of the climate control panel, and the top tions, the system does not attempt automatic comfort control. center of the instrument panel should be kept free of debris due to the climate control sensor’s location.
  • Page 269 UNDERSTANDING YOUR INSTRUMENT PANEL 267 • Most of the time, when in Automatic operation, you Manual Operation can temporarily put the system into Recirculation This system offers a full complement of manual override mode by pressing the “Recirculation” button. How- features which consist of Blower Preferred Automatic, ever, under certain conditions in automatic the system Mode Preferred Automatic with Manual Air Temperature...
  • Page 270 268 UNDERSTANDING YOUR INSTRUMENT PANEL I n f o r m a t i o n P r o v i d e d b y :...
  • Page 271 UNDERSTANDING YOUR INSTRUMENT PANEL 269 NOTE: Regardless of the type of operation, when a NOTE: The defrost mode is not automatically selected. temperature knob is set to the full clockwise or full It must be manually selected, when desired. counterclockwise position, the system will deliver full Defrost/Floor hot or full cold air out of the ducts, respectively.
  • Page 272 270 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level outlets selected on the mode control dial. The button Air flows both through the outlets located in the includes an LED that illuminates when manual operation instrument panel and those located on the floor. Air is selected.
  • Page 273: Operating Tips

    UNDERSTANDING YOUR INSTRUMENT PANEL 271 captured interior air to condense on windows and ham- control and blower speed to maintain comfort. Higher per visibility. For this reason, the system will not allow blower speeds will reduce fogging. Interior fogging on “Recirculation”...
  • Page 274 272 UNDERSTANDING YOUR INSTRUMENT PANEL When using the air conditioner in extremely heavy Winter Operation traffic, in hot weather, especially when towing a trailer, When operating the system during the winter months, additional engine cooling may be required. If this situa- make sure the air intake, located directly in front of the tion is encountered, operate the transmission in a lower windshield, is free of ice, slush, snow, or other...
  • Page 275: Operating Tips Chart

    UNDERSTANDING YOUR INSTRUMENT PANEL 273 Operating Tips Chart I n f o r m a t i o n P r o v i d e d b y :...
  • Page 276 I n f o r m a t i o n P r o v i d e d b y :...
  • Page 277: Starting And Operating

    STARTING AND OPERATING CONTENTS Starting Procedure ..... 280 Brake/Transmission Shift Interlock System . . 287 Normal Starting ..... 280 Brake/Transmission Interlock Manual Override .
  • Page 278 276 STARTING AND OPERATING Quadra-Trac II Operating Power Steering ..... . . 306 Instructions/Precautions — If Equipped ..297 Power Steering Fluid Check .
  • Page 279 STARTING AND OPERATING 277 HDC (Hill Descent Control) (4WD Models Compact Spare Tire — If Equipped ..338 With NV245 Two–Speed Transfer Limited-Use Spare — If Equipped ..339 Case Only) .
  • Page 280 278 STARTING AND OPERATING Fuel Requirements ..... 355 E-85 General Information ....361 3.7 And 4.7L Engine .
  • Page 281 STARTING AND OPERATING 279 Trailer Towing ......369 Snow Plow ......382 Common Towing Definitions .
  • Page 282: Starting Procedure

    280 STARTING AND OPERATING STARTING PROCEDURE Normal Starting Before starting your vehicle, adjust your seat, adjust the Tip Start inside and outside mirrors, fasten your seat belt, and if present, instruct all other occupants to buckle their seat NOTE: Normal starting of either a cold or a warm belts.
  • Page 283: Extremely Cold Weather (Below 20°F Or 29°C)

    STARTING AND OPERATING 281 Extremely Cold Weather (Below 20°F or 29°C) WARNING! (Continued) To ensure reliable starting at these temperatures, use of • Do not attempt to push or tow your vehicle to get an externally powered electric engine block heater (avail- it started.
  • Page 284: After Starting

    282 STARTING AND OPERATING • Low Oil Pressure Light is off. release it as soon as the starter engages. The starter motor will disengage automatically in 10 seconds. Once this Cold Weather Precautions occurs, release the accelerator pedal, turn the ignition Operation in ambient temperature below 32°F (0°C) may switch to the LOCK position, wait 10 to 15 seconds, then require special considerations.
  • Page 285 STARTING AND OPERATING 283 NOTE: blankets will greatly increase starting capability at low • Use of Climatized ULSD Diesel Fuel or Number 1 temperatures. Suitable battery blankets are available ULSD Diesel Fuel results in a noticeable decrease in from your authorized MOPAR dealer. fuel economy.
  • Page 286 284 STARTING AND OPERATING depending on engine temperature. When the “Wait To Incomplete combustion allows carbon and varnish to Start” goes out, the engine is ready to start. form on piston rings and injector nozzles. Also, the unburned fuel can enter the crankcase, diluting the oil 4.
  • Page 287: Engine Block Heater - If Equipped

    STARTING AND OPERATING 285 Engine Idling - In Cold Weather allow the lubricating oil and coolant to carry excess heat Avoid prolonged idling in ambient temperatures below away from the combustion chamber, bearings, internal 0°F (-18°C). Long periods of idling may be harmful to components, and turbocharger.
  • Page 288: Automatic Transmission

    286 STARTING AND OPERATING • 5.7L Engine — bundled and fastened to the injector AUTOMATIC TRANSMISSION harness. CAUTION! • 3.0L Diesel Engine — on the passenger side of the vehicle, mounted on a stud between the fresh airbox Damage to the transmission may occur if the follow- and coolant reservoir.
  • Page 289: Brake/Transmission Shift Interlock System

    STARTING AND OPERATING 287 Brake/Transmission Interlock Manual Override WARNING! Your vehicle may be equipped with a shift lock manual override. The manual override may be used in the event It is dangerous to move the shift lever out of PARK or that the shift lever should fail to move from PARK with NEUTRAL if the engine speed is higher than idle the key in the ON position and the brake pedal de-...
  • Page 290: Five-Speed Automatic Transmission

    288 STARTING AND OPERATING 5. Using the screwdriver, reach into the manual override Have your vehicle inspected by your local authorized opening. Press and hold the shift lock lever down. dealer, if the shift lock manual override has been used. Five–Speed Automatic Transmission The electronically controlled transmission provides a precise shift schedule.
  • Page 291 STARTING AND OPERATING 289 PARK WARNING! (Continued) This gear position supplements the parking brake by • It is dangerous to move the shift lever out of PARK locking the transmission. The engine can be started in or NEUTRAL if the engine speed is higher than this range.
  • Page 292 290 STARTING AND OPERATING NOTE: Towing the vehicle, coasting, or driving for any shifts the transmission into ERS 3 (third gear), the trans- other reason with the shift lever in NEUTRAL can result mission will never shift above third gear, but can shift in severe transmission damage.
  • Page 293 STARTING AND OPERATING 291 transmission will downshift to 4th gear and the display gear). When in the DRIVE position in 5th gear, the first will show 4. Another tap to the left (-) will shift the tap to the left (-) will downshift the transmission and transmission into 3rd gear.
  • Page 294 292 STARTING AND OPERATING • transmission left “D(-)” and hold it there. The transmission will shift to reached normal operating the range from which the vehicle can best be slowed temperature. down. NOTE: If the vehicle is started in extremely cold tem- Overdrive Operation peratures, the transmission may not shift into Overdrive The automatic transmission includes an electronically...
  • Page 295 STARTING AND OPERATING 293 OVER TEMP” message may display, and the transmis- overheating or failure due to excessive shifting. When sion may downshift out of Overdrive until the transmis- operating in TOW/HAUL mode, the transmission will sion cools down. After cool down, the transmission will shift into direct gear and Overdrive will be enabled resume normal operation.
  • Page 296 294 STARTING AND OPERATING activated. Pressing the switch a second time restores 4. Wait approximately 10 seconds, then restart the en- normal operation. If the TOW/HAUL mode is desired, gine. the switch must be pressed each time the engine is 5.
  • Page 297: Rocking The Vehicle

    STARTING AND OPERATING 295 • If the vehicle has not been driven in several days, the drops below a calibrated speed, or during acceleration, the clutch automatically and smoothly disengages. The first few seconds of operation after shifting the trans- feature is operational in Overdrive and in DRIVE.
  • Page 298: Four-Wheel Drive Operation

    296 STARTING AND OPERATING The least amount of accelerator pedal pressure to main- FOUR-WHEEL DRIVE OPERATION tain the rocking motion, without spinning the wheels or Quadra-Trac I Operating racing the engine, is most effective. Racing the engine or Instructions/Precautions — If Equipped spinning the wheels, due to the frustration of not freeing The Quadra-Trac I is a single-speed (HI range only) the vehicle, may lead to transmission overheating and...
  • Page 299: Quadra-Trac Ii Operating Instructions/Precautions - If Equipped

    STARTING AND OPERATING 297 Quadra-Trac II Operating Proper operation of four-wheel drive vehicles depends Instructions/Precautions — If Equipped on tires of equal size, type, and circumference on each The Quadra-Trac II transfer case is fully automatic in the wheel. Any difference will adversely affect shifting and normal driving 4WD HI mode.
  • Page 300: Shift Positions

    298 STARTING AND OPERATING Shift Positions Shifting Procedures For additional information on the appropriate use of each 4WD HI to 4WD LOW transfer case mode position, see the information below: With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), key ON or engine running, shift the transmission into 4WD HI NEUTRAL, and raise the transfer case T-handle.
  • Page 301 STARTING AND OPERATING 299 “4WD LOW” indicator light in the instrument cluster, will flash and go out when the shift is complete. Release the T-handle. NOTE: • If shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “CHECK SHIFT PROCEDURES”...
  • Page 302 300 STARTING AND OPERATING NEUTRAL Shift Procedure 1. Key ON, engine off. 2. Vehicle stopped, with foot on brake. 3. Place transmission into NEUTRAL. 4. Hold down the NEUTRAL “pin” switch (with a pen, etc.) for four seconds until the LED lamp by the switch starts to blink indicating shift in progress.
  • Page 303: Quadra-Drive Ii System - If Equipped

    STARTING AND OPERATING 301 Quadra-Drive II System — If Equipped ON-ROAD DRIVING TIPS The optional Quadra-Drive II System features three Utility vehicles have higher ground clearance and a torque transfer couplings. The couplings include ELSD narrower track to make them capable of performing in a (Electronic Limited-Slip Differential) front and rear axles wide variety of off-road applications.
  • Page 304: Off-Road Driving Tips

    302 STARTING AND OPERATING OFF-ROAD DRIVING TIPS CAUTION! NOTE: Prior to off-road driving, remove the front air When driving through water, do not exceed 5 mph dam to prevent damage. The front air dam is attached to (8 km/h). Always check water depth before entering the lower front fascia with quarter turn fasteners, and can as a precaution, and check all fluids afterward.
  • Page 305: Driving In Snow, Mud And Sand

    STARTING AND OPERATING 303 Flowing Water transfer case) to assure the fluids have not been contami- If the water is swift flowing and rising (as in storm nated. Contaminated fluid (milky, foamy in appearance) run-off) avoid crossing until the water level recedes should be flushed/changed as soon as possible to pre- and/or the flow rate is reduced.
  • Page 306: Hill Climbing

    304 STARTING AND OPERATING Hill Climbing WARNING! NOTE: Before attempting to climb a hill, determine the If the engine stalls, you lose forward motion, or conditions at the crest and/or on the other side. cannot make it to the top of a steep hill or grade, Before climbing a steep hill, shift the transmission to a never attempt to turn around.
  • Page 307: Traction Downhill

    STARTING AND OPERATING 305 • Completely inspect the underbody of your vehicle. Traction Downhill Shift the transmission into a low gear, and the transfer Check tires, body structure, steering, suspension, and case into 4WD LOW range. Let the vehicle go slowly exhaust system for damage.
  • Page 308: Power Steering

    306 STARTING AND OPERATING If for some reason the power assist is interrupted, it will WARNING! still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering Abrasive material in any part of the brakes may cause effort, especially at very low vehicle speeds and during excessive wear or unpredictable braking.
  • Page 309: Power Steering Fluid Check

    STARTING AND OPERATING 307 WARNING! WARNING! Continued operation with reduced power steering Do not use Automatic Transmission Fluid (ATF), or assist could pose a safety risk to yourself and others. other types of power steering fluids, when servicing Service should be obtained as soon as possible. the power steering system of this vehicle.
  • Page 310: Parking Brake

    308 STARTING AND OPERATING NOTE: The Brake Warning Light indicates only that the WARNING! parking brake is applied. It does not indicate the degree of brake application. Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to ensure accurate fluid level reading.
  • Page 311: Anti-Lock Brake System

    STARTING AND OPERATING 309 the shift lever in PARK, otherwise the load on the WARNING! (Continued) transmission locking mechanism may make it difficult to • Be sure the parking brake is fully disengaged move the shift lever out of PARK. before driving, failure to do so can lead to brake problems due to excessive heating of the rear WARNING!
  • Page 312 310 STARTING AND OPERATING wheel lock-up and help avoid skidding on slippery The ABS pump motor runs during the self-test at 12 mph surfaces. (20 km/h) and during an ABS stop. The pump motor makes a low humming noise during operation, which is All vehicle wheels and tires must be the same size and normal.
  • Page 313 STARTING AND OPERATING 311 NOTE: During severe braking conditions, a pulsing WARNING! (Continued) sensation may occur and a clicking noise will be heard. • The ABS cannot prevent accidents, including This is normal, indicating that the ABS is functioning. those resulting from excessive speed in turns, •...
  • Page 314: Electronic Brake Control System

    312 STARTING AND OPERATING • Do not drive too fast for road conditions, especially Also, your vehicle is equipped with TSC (Trailer Sway when roads are wet or slushy. A wedge of water can Control) and, if it has 4WD with the NV245 two-speed build up between the tire tread and the road.
  • Page 315: Tcs (Traction Control System)

    STARTING AND OPERATING 313 stability. A feature of the TCS system functions similar to WARNING! a limited-slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is ABS (Anti-Lock Brake System) cannot prevent the spinning faster than the other, the system will apply the natural laws of physics from acting on the vehicle, brake of the spinning wheel.
  • Page 316: Erm (Electronic Roll Mitigation)

    314 STARTING AND OPERATING benefit of the system, you must apply continuous brak- ERM (Electronic Roll Mitigation) ing pressure during the stopping sequence (do not This system anticipates the potential for wheel lift by “pump” the brakes). Do not reduce brake pedal pressure monitoring the driver’s steering wheel input and the unless braking is no longer desired.
  • Page 317: Esp (Electronic Stability Program)

    STARTING AND OPERATING 315 NOTE: Anytime the ESP system is in the “Full Off” ESP (Electronic Stability Program) mode, ERM is disabled. Refer to ESP (Electronic Stability This system enhances directional control and stability of Program) for a complete explanation of the available ESP the vehicle under various driving conditions.
  • Page 318 316 STARTING AND OPERATING • Understeer - when the vehicle is turning less than WARNING! appropriate for the steering wheel position. ESP (Electronic Stability Program) cannot prevent the The ESP/TCS Indicator Light located in the instrument natural laws of physics from acting on the vehicle, cluster, starts to flash as soon as the tires lose traction and nor can it increase the traction afforded by prevailing the ESP system becomes active.
  • Page 319 STARTING AND OPERATING 317 High Range (4WD Models) or 2WD Models conditions and more wheel spin than ESP would nor- mally allow is required to gain traction. To turn ESP on again, momentarily depress the ESP OFF switch. This This is the normal operating mode for ESP in 4WD HIGH will restore the normal “ESP On”...
  • Page 320 318 STARTING AND OPERATING NOTE: To improve the vehicle’s traction when driving In this mode, ESP and TCS, except for the “limited slip” with snow chains, or starting off in deep snow, sand, or feature described in the TCS section, are turned off until gravel, it may be desirable to switch to the “Partial Off”...
  • Page 321 STARTING AND OPERATING 319 (64 km/h), the normal ESP stability function returns but WARNING! TCS remains off. When the vehicle speed drops below 35 mph (56 km/h), the ESP system shuts off. ESP is With the ESP switched off, the enhanced vehicle deactivated at low vehicle speeds in 4WD LOW range so stability offered by ESP and ERM are unavailable.
  • Page 322: Tsc (Trailer Sway Control)

    320 STARTING AND OPERATING follow the trailer tongue weight recommendations. Refer WARNING! to “Trailer Towing” in Section 5 of this manual. When TSC is functioning, the ESP/TCS Indicator Light will With the ESP switched off, the enhanced vehicle flash, the engine power may be reduced and you may stability offered by ESP and ERM are unavailable.
  • Page 323 STARTING AND OPERATING 321 period of time after the driver takes their foot off of the HSA will work in REVERSE and all forward gears when brake pedal. If the driver does not apply the throttle the activation criteria have been met. The system will not during this short period of time, the system will release activate if the vehicle is placed in NEUTRAL or PARK.
  • Page 324 322 STARTING AND OPERATING WARNING! WARNING! (Continued) • HSA is not a parking brake. If you stop the vehicle • If you use a trailer brake controller with your on a hill without putting the transmission in trailer, your trailer brakes may be activated and PARK and using the parking brake, it will roll deactivated with the brake switch.
  • Page 325: Hdc (Hill Descent Control) (4Wd Models With Nv245 Two-Speed Transfer Case Only)

    STARTING AND OPERATING 323 HDC (Hill Descent Control) (4WD Models With NV245 Two–Speed Transfer Case Only) HDC maintains vehicle speed while descending hills during off-road driving situations and is available in 4WD LOW range only. To enable HDC (transfer case must be in 4WD LOW range), press the HDC switch.
  • Page 326 324 STARTING AND OPERATING and will only activate when the vehicle is descending a HDC also has the capability to sense rough terrain, and hill. It will usually not activate on level ground. will automatically adjust to a slightly slower set speed (about 0.3 mph (0.5 km/h) than normal.
  • Page 327: Esp/Bas Warning Light And Esp/Tcs Indicator Light

    STARTING AND OPERATING 325 after several ignition cycles, and the vehicle has been WARNING! driven several miles at speeds greater than 30 mph (48 km/h), see your authorized dealer as soon as possible HDC is only intended to assist the driver in control- to have the problem diagnosed and corrected.
  • Page 328: Tire Safety Information

    326 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
  • Page 329 STARTING AND OPERATING 327 • Temporary spare tires are high-pressure compact • High flotation tire sizing is based on U.S. design spares designed for temporary emergency use only. standards and it begins with the tire diameter molded Tires designed to this standard have the letter “T” into the sidewall.
  • Page 330 328 STARTING AND OPERATING EXAMPLE: R = Construction code — R means radial construction — D means diagonal or bias construction 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol —...
  • Page 331 STARTING AND OPERATING 329 EXAMPLE: Load Identification: ..blank..= Absence of any text on the sidewall of the tire indicates a Standard Load (SL) tire Extra Load (XL) = Extra load (or reinforced) tire Light Load = Light load tire C, D, E = Load range associated with the maximum load a tire can carry at a specified pressure Maximum Load —...
  • Page 332: Tire Identification Number (Tin)

    330 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
  • Page 333: Tire Loading And Tire Pressure

    STARTING AND OPERATING 331 Tire Loading and Tire Pressure This placard tells you important information about the: Tire Placard Location 1) number of people that can be carried in the vehicle NOTE: The proper cold tire inflation pressure is listed 2) total weight your vehicle can carry on the driver’s side B-Pillar.
  • Page 334 332 STARTING AND OPERATING axles must not be exceeded. For further information on 3. Subtract the combined weight of the driver and pas- GAWRs, vehicle loading, and trailer towing, refer to sengers from XXX lbs or XXX kg. “Vehicle Loading” in this section. 4.
  • Page 335 STARTING AND OPERATING 333 • For the following example, the combined weight of NOTE: • The following table shows examples on how to calcu- occupants and cargo should never exceed 865 lbs late total load, cargo/luggage, and towing capacities (392 kg). of your vehicle with varying seating configurations and number and size of occupants.
  • Page 336 334 STARTING AND OPERATING I n f o r m a t i o n P r o v i d e d b y :...
  • Page 337: Tires - General Information

    STARTING AND OPERATING 335 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
  • Page 338: Tire Inflation Pressures

    336 STARTING AND OPERATING of the vehicle and can produce a feeling of sluggish WARNING! (Continued) response or over responsiveness in the steering. • Unequal tire pressures from one side of the vehicle Unequal tire pressures can cause erratic and unpredict- to the other can cause the vehicle to drift to the right able steering response.
  • Page 339: Tire Pressures For High Speed Operation

    STARTING AND OPERATING 337 Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the winter.
  • Page 340: Radial-Ply Tires

    338 STARTING AND OPERATING loading may be required for high-speed vehicle opera- Radial-Ply Tires tion. Refer to original equipment or an authorized tire WARNING! dealer for recommended safe operating speeds, loading and cold tire inflation pressures. Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle WARNING! poorly.
  • Page 341: Limited-Use Spare - If Equipped

    STARTING AND OPERATING 339 WARNING! CAUTION! Temporary use spare tires are for emergency use only. Because of the reduced ground clearance, do not take With these tires, do not drive more than 50 mph your vehicle through an automatic car wash with the (80 km/h).
  • Page 342: Tire Spinning

    340 STARTING AND OPERATING WARNING! WARNING! The limited-use spare tires are for emergency use Fast spinning tires can be dangerous. Forces gener- only. Installation of this limited-use spare tire affects ated by excessive wheel speeds may cause tire dam- vehicle handling. With this tire, do not drive more age or failure.
  • Page 343: Life Of Tire

    STARTING AND OPERATING 341 Many states have laws requiring tire replacement at this point. Life Of Tire The service life of a tire is dependent upon various factors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! 1 —...
  • Page 344: Replacement Tires

    342 STARTING AND OPERATING Keep dismounted tires in a cool, dry place with as little WARNING! exposure to light as possible. Protect tires from contact • Do not use a tire, wheel size or rating other than with oil, grease, and gasoline. that specified for your vehicle.
  • Page 345: Tire Chains

    STARTING AND OPERATING 343 • Do not install tire chains or traction devices on ve- WARNING! (Continued) hicles with larger than P235/65R17 tires. Tires larger • Failure to equip your vehicle with tires having than this may not provide sufficient body clearance adequate speed capability can result in sudden tire with chains or other traction devices.
  • Page 346: Tire Rotation Recommendations

    344 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS These effects can be reduced by timely rotation of tires. Tires on the front and rear axles of vehicles operate at The benefits of rotation are especially worthwhile with different loads and perform different steering, handling, aggressive tread designs such as those on On/Off-Road and braking functions.
  • Page 347: Tire Pressure Monitor System (Tpms)

    STARTING AND OPERATING 345 TIRE PRESSURE MONITOR SYSTEM (TPMS) The TPMS will warn the driver of a low tire pressure if The Tire Pressure Monitoring System (TPMS) will warn the tire pressure falls below the low pressure warning the driver of a low tire pressure based on the vehicle threshold for any reason, including low temperature recommended cold tire pressure.
  • Page 348 346 STARTING AND OPERATING For example, your vehicle has a recommended cold CAUTION! (parked for more than three hours) tire pressure of 33 psi • The TPMS has been optimized for the original (227 kPa). If the ambient temperature is 68°F (20°C) and the measured tire pressure is 28 psi (193 kPa), a tempera- equipment tires and wheels.
  • Page 349: Base System

    STARTING AND OPERATING 347 • Seasonal temperature changes will affect tire pressure, NOTE: • The TPMS is not intended to replace normal tire care and the TPMS will monitor the actual tire pressure in and maintenance, or to provide warning of a tire the tire.
  • Page 350 348 STARTING AND OPERATING A tire pressure monitoring sensor is located in the spare pressures have been received. The vehicle may need to be wheel, if the vehicle is equipped with a matching full-size driven for up to 20 minutes above 15 mph (24 km/h) to spare wheel and tire assembly.
  • Page 351 STARTING AND OPERATING 349 3. Lots of snow or ice around the wheels or wheel Tire Pressure Monitoring Telltale Light as long as none housings. of the road tires are below the low pressure warning threshold. 4. Using tire chains on the vehicle. •...
  • Page 352: Premium System - If Equipped

    350 STARTING AND OPERATING TPM SYSTEM” message will be displayed for 75 sec- NOTE: It is particularly important, for you to regularly onds, and the Tire Pressure Monitoring Telltale Light check the tire pressure in all of your tires and to maintain will flash on and off for 75 seconds and then remain on the proper pressure.
  • Page 353 STARTING AND OPERATING 351 spare tire can be used in place of any of the four road tires. A low spare tire will set the “SPARE LOW PRES- SURE” message, but it will not cause the Tire Pressure Monitoring Telltale Light to illuminate or the chime to sound.
  • Page 354 352 STARTING AND OPERATING once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information. CHECK TPM SYSTEM Warning The Tire Pressure Monitoring Telltale Light will flash on and off for 75 seconds, and remain on solid when a system fault is detected.
  • Page 355 STARTING AND OPERATING 353 If the ignition key is cycled, this sequence will repeat, The EVIC will also display a CHECK TPM SYSTEM providing the system fault still exists. If the system fault message for three seconds when a system fault is de- no longer exists, the Tire Pressure Monitoring Telltale tected possibly related to the trigger component.
  • Page 356 354 STARTING AND OPERATING show the low tire pressure value “flashing.” Driving the Tire Pressure Monitoring Telltale Light will flash the vehicle for up to 20 minutes above 15 mph on and off for 75 seconds and then remain on solid. In (24 km/h) will turn OFF the Tire Pressure Monitoring addition, the EVIC will display a “CHECK TPM Telltale Light as long as none of road tires are below...
  • Page 357: General Information

    STARTING AND OPERATING 355 be driven for up to 20 minutes above 15 mph (24 km/h) FUEL REQUIREMENTS in order for the TPMS to receive this information. 3.7 and 4.7L Engine All engines (except 5.7L engines) are de- General Information This device complies with part 15 of the FCC rules and signed to meet all emissions regulations RSS 210 of Industry Canada.
  • Page 358: Reformulated Gasoline

    356 STARTING AND OPERATING for optimum performance. The use of premium gasoline Reformulated Gasoline is not recommended, as it will not provide any benefit Many areas of the country require the use of cleaner over regular gasoline in these engines. burning gasoline referred to as “Reformulated Gasoline.”...
  • Page 359: E-85 Usage In Non-Flex Fuel Vehicles

    STARTING AND OPERATING 357 • OBD II “Malfunction Indicator Light” on CAUTION! • poor engine performance DO NOT use gasoline containing Methanol. Use of • poor cold start and cold drivability these blends may result in starting and drivability problems and may damage critical fuel system com- •...
  • Page 360: Materials Added To Fuel

    358 STARTING AND OPERATING blended with MMT provides no performance advantage conditions and would result in additional cost. Therefore, beyond gasoline of the same octane number without you should not have to add anything to the fuel. MMT. Gasoline blended with MMT reduces spark plug Fuel System Cautions life and reduces emission system performance in some vehicles.
  • Page 361: Carbon Monoxide Warnings

    STARTING AND OPERATING 359 • The use of fuel additives which are now being sold as Never run the engine in a closed area, such as a octane enhancers is not recommended. Most of these garage, and never sit in a parked vehicle with the products contain high concentrations of methanol.
  • Page 362: Fuel Requirements (Diesel Engines)

    360 STARTING AND OPERATING FUEL REQUIREMENTS (DIESEL ENGINES) Use good quality diesel fuel from a reputable supplier. For most year-round service, No. 2 diesel fuel, meeting NOTE: Federal law requires that you must fuel this ASTM specification D-975 Grade S15, will provide good vehicle with Ultra Low Sulfur Highway Diesel fuel (15 performance.
  • Page 363: Flexible Fuel (4.7L Engine Only) - If Equipped

    STARTING AND OPERATING 361 Diesel fuel is seldom completely free of water. To prevent for information on features that are common between fuel system trouble, drain the accumulated water from Flexible Fuel and gasoline-only powered vehicles. the fuel/water separator using the provided fuel/water separator drain.
  • Page 364: Ethanol Fuel (E-85)

    362 STARTING AND OPERATING ETHANOL FUEL (E-85) CAUTION! E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. Only vehicles with the E-85 fuel filler cap (gas cap) can operate on E-85. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury.
  • Page 365: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles

    STARTING AND OPERATING 363 For best results, a refueling pattern that avoids alternat- Selection Of Engine Oil For Flexible Fuel Vehicles ing between E-85 and unleaded gasoline is recom- (E-85) and Gasoline Vehicles mended. Whether operating the vehicle on an E-85 ethanol fuel or unleaded gasoline, the engine oil requirements are the When you do switch fuel types it is recommended that: same.
  • Page 366: Replacement Parts

    364 STARTING AND OPERATING consumption. You can expect your MPG and your driv- ADDING FUEL ing range to decrease by about 30% compared to gasoline CAUTION! operation. Replacement Parts DO NOT put gasoline in your diesel vehicle (if All components in your Flexible Fuel Vehicle (FFV) are equipped).
  • Page 367 STARTING AND OPERATING 365 CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel cap (gas cap). A poorly fitting cap could let impu- rities into the fuel system. Also, a poorly fitting aftermarket cap can cause the Malfunction Indica- tor Light (MIL) to illuminate, due to fuel vapors escaping from the system.
  • Page 368 366 STARTING AND OPERATING WARNING! WARNING! • Never have any smoking materials lit in or near A fire may result if gasoline is pumped into a the vehicle when the gas cap is removed or the portable container that is inside of a vehicle. You tank filled.
  • Page 369: Vehicle Loading

    STARTING AND OPERATING 367 included on this label and indicates the month, day, and CAUTION! hour of manufacture. The bar code that appears on the bottom of the label is your VIN. Damage to the fuel system or emission control sys- tem could result from using an improper fuel tank Gross Vehicle Weight Rating (GVWR) filler cap (gas cap).
  • Page 370 368 STARTING AND OPERATING Each axle’s GAWR is determined by the components in Curb Weight the system with the lowest load carrying capacity (axle, The curb weight of a vehicle is defined as the total weight springs, tires, or wheels). Heavier axles or suspension of the vehicle with all fluids, including vehicle fuel, at full components, sometimes specified by purchasers for in- capacity conditions, and with no occupants or cargo...
  • Page 371: Trailer Towing

    STARTING AND OPERATING 369 the front or rear axles has been exceeded, but the total TRAILER TOWING load is within the specified GVWR. If so, weight must be In this section you will find safety tips and information shifted from front to rear, or rear to front, as appropriate on limits to the type of towing you can reasonably do until the specified weight limitations are met.
  • Page 372 370 STARTING AND OPERATING Gross Trailer Weight (GTW) WARNING! The GTW is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or tem- It is important that you do not exceed the maximum porary) loaded in or on the trailer in its loaded and front or rear GAWR.
  • Page 373 STARTING AND OPERATING 371 some other connecting point of the vehicle. These kind of depending on Vehicle and Trailer configuration/loading hitches are the most popular on the market today and to comply with gross axle weight rating (GAWR) they are commonly used to tow small- and medium- requirements.
  • Page 374: Trailer Hitch Classification

    372 STARTING AND OPERATING Trailer Hitch Classification Trailer Hitch Classification Definitions Your vehicle may be factory equipped for safe towing of Class Max. Trailer Hitch Industry trailers weighing over 3,500 lbs (1 587 kg) with the Standards optional Trailer Tow Prep Package. See your authorized Class I - Light Duty 2,000 lbs (907 kg) dealer for package content.
  • Page 375: Trailer Towing Weights (Maximum Trailer Weight Ratings)

    STARTING AND OPERATING 373 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Model Model GCWR (Gross Com- Frontal Area Max. GTW (Gross Max. Trailer bined Wt. Rating) Trailer Wt.) Tongue Wt.
  • Page 376 374 STARTING AND OPERATING 3.0L Diesel 12,200 lbs (5 534 kg) 64 sq ft (5.95 sq m) 7,400 lbs (3 357 kg) 740 lbs (336 kg) (Limited) 3.0L Diesel 12,250 lbs (5 556 kg) 64 sq ft (5.95 sq m) 7,400 lbs (3 357 kg) 740 lbs (336 kg) (Overland)
  • Page 377: Trailer And Trailer Tongue Weight

    STARTING AND OPERATING 375 Trailer And Trailer Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
  • Page 378: Towing Requirements

    376 STARTING AND OPERATING NOTE: Remember that everything put into or on the CAUTION! (Continued) trailer adds to the load on your vehicle. Also, additional • During the first 500 miles (805 km) of trailer factory-installed options, or authorized dealer-installed towing, limit your speed to 50 mph (80 km/h).
  • Page 379 STARTING AND OPERATING 377 four-wheel drive vehicles, make sure the transfer case WARNING! (Continued) is not in NEUTRAL. Always, block or chock the • Improper towing can lead to an injury accident. trailer wheels. Follow these guidelines to make your trailer tow- •...
  • Page 380 378 STARTING AND OPERATING Towing Requirements — Tires Towing Requirements — Trailer Brakes − Do not attempt to tow a trailer while using a compact − Do not interconnect the hydraulic brake system or spare tire. vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible −...
  • Page 381 STARTING AND OPERATING 379 CAUTION! WARNING! (Continued) • Towing any trailer will increase your stopping If the trailer weighs more than 1,000 lbs (454 kg) distance. When towing, you should allow for ad- loaded, it should have its own brakes and they ditional space between your vehicle and the ve- should be of adequate capacity.
  • Page 382 380 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 7-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 —...
  • Page 383: Towing Tips

    STARTING AND OPERATING 381 Towing Tips The transmission fluid and filter should be changed if Before setting out on a trip, practice turning, stopping you REGULARLY tow a trailer for more than 45 minutes and backing the trailer in an area away from heavy of continuous operation.
  • Page 384: Snow Plow

    382 STARTING AND OPERATING Cooling System WARNING! To reduce potential for engine and transmission over- heating, take the following actions: Do not add a snow plow, winches, or any other aftermarket equipment to the front of your vehicle. − City Driving This could adversely affect the functioning of the When stopped for short periods of time, shift the trans- airbag system and you could be injured.
  • Page 385: Towing - Quadra-Trac I (Single-Speed Transfer Case) 4Wd Models

    STARTING AND OPERATING 383 Towing — Quadra-Trac I (Single-Speed Transfer Shifting Into NEUTRAL Case) 4WD Models Use the following procedure to prepare your vehicle for recreational towing. Recreational towing is not allowed. This model does not have a NEUTRAL position in the transfer case. CAUTION! Towing —...
  • Page 386 384 STARTING AND OPERATING Hold down the NEUTRAL “pin” switch (with a pen, etc.) for four seconds until the LED lamp by the switch starts to blink, indicating shift in progress. The lamp will stop blinking (stay on solid) when the NEUTRAL shift is complete.
  • Page 387 STARTING AND OPERATING 385 9. Shift the transmission into PARK. Shifting Out Of NEUTRAL Use the following procedure to prepare your vehicle for 10. Place the ignition key in the OFF position, and normal usage. remove key. 1. Depress the brake pedal. 11.
  • Page 388 386 STARTING AND OPERATING Hold down the NEUTRAL “pin” switch (with a pen, etc.) for four seconds until the LED lamp by the switch starts to blink, indicating shift in progress. The lamp will stop blinking (go out) when shift is complete. The “4WD SYSTEM IN NEUTRAL”...
  • Page 389 STARTING AND OPERATING 387 NOTE: When shifting out of transfer case NEUTRAL, CAUTION! turning the engine OFF may be required to avoid gear clash. Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the...
  • Page 390 I n f o r m a t i o n P r o v i d e d b y :...
  • Page 391: What To Do In Emergencies

    WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flashers ....390 Jacking Instructions ....394 If Your Engine Overheats .
  • Page 392: Hazard Warning Flashers

    390 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the switch bank just above the climate controls. potential for overheating by taking the appropriate ac- tion.
  • Page 393: Jacking And Tire Changing

    WHAT TO DO IN EMERGENCIES 391 JACKING AND TIRE CHANGING CAUTION! WARNING! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT • Getting under a jacked-up vehicle is dangerous. (H), pull over and stop the vehicle. Idle the vehicle The vehicle could slip off the jack and fall on you.
  • Page 394: Jack Location

    392 WHAT TO DO IN EMERGENCIES Jack Location Spare Tire Stowage The scissor-type jack and tire changing tools are located The spare tire is stowed under the rear of the vehicle by in the passenger side compartment, behind the second means of a cable winch mechanism.
  • Page 395: Spare Tire Removal

    WHAT TO DO IN EMERGENCIES 393 CAUTION! • The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch. • When the spare is clear, tilt the retainer at the end of the cable and pull it through the center of the wheel.
  • Page 396: Jacking Instructions

    394 WHAT TO DO IN EMERGENCIES NOTE: Passengers should not remain in the vehicle WARNING! when the vehicle is being jacked. Do not attempt to change a tire on the side of the Jacking Instructions vehicle closest to moving traffic. Pull far enough off the road to avoid being hit when operating the jack WARNING! or changing the wheel.
  • Page 397 WHAT TO DO IN EMERGENCIES 395 WARNING! (Continued) • Never start or run the engine with the vehicle on a jack. • Do not let anyone sit in the vehicle when it is on a jack. Jack Warning Label • Do not get under the vehicle when it is on a jack. 1.
  • Page 398 396 WHAT TO DO IN EMERGENCIES 3. Assemble the jack and jacking tools as shown. Connect 4. Locate the jack as shown. For the front axle, place it jack handle driver (1) to two extensions (2), then to the under the front lower control arm as shown. For the rear lug wrench (3).
  • Page 399 WHAT TO DO IN EMERGENCIES 397 WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it. Raise the vehicle only enough to remove the tire. 6. Remove the lug nuts and wheel. 7.
  • Page 400: Jump-Starting

    398 WHAT TO DO IN EMERGENCIES wheel nut tightness is 95 ft lbs (130 N·m). If in doubt Double check to ensure the tire is snug against the about the correct tightness, have them checked with a underbody of the vehicle. Damage to the winch cable torque wrench by your authorized dealer or at a service may result if the vehicle is driven with the tire loose.
  • Page 401 WHAT TO DO IN EMERGENCIES 399 2. Park the booster vehicle within cable reach but with- WARNING! out letting the vehicles touch. Set the parking brake on • Battery fluid is a corrosive acid solution; do not both vehicles, place the transmission in PARK, and turn the ignition OFF.
  • Page 402: Emergency Tow Hooks - If Equipped

    400 WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal WARNING! (Continued) of the booster battery and then to the engine of the • Damage to charging system of booster vehicle or vehicle with the discharged battery. Make sure you have of immobilized vehicle.
  • Page 403: Towing A Disabled Vehicle

    WHAT TO DO IN EMERGENCIES 401 vehicle. The rear hook will be located on the driver’s side TOWING A DISABLED VEHICLE of the vehicle. 2–Wheel Drive Models Only NOTE: For off-road recovery, it is recommended to use Provided the transmission is operable, tow only in NEU- both of the front tow hooks to minimize the risk of TRAL at speeds not exceeding 30 mph (48 km/h), for damage to the vehicle.
  • Page 404 I n f o r m a t i o n P r o v i d e d b y :...
  • Page 405: Maintaining Your Vehicle

    MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment – 3.7L ....406 Dealer Service ......413 Engine Compartment –...
  • Page 406 404 MAINTAINING YOUR VEHICLE Exhaust System ..... 422 Underhood Fuses (Integrated Power Module) ... . . 447 Cooling System .
  • Page 407 MAINTAINING YOUR VEHICLE 405 Fluids And Capacities ....456 Engine ......458 Fluids, Lubricants, And Genuine Parts .
  • Page 408: Engine Compartment - 3.7L

    406 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 3.7L 1 — Engine Coolant Reservoir 6 — Battery 2 — Engine Oil Dipstick 7 — Washer Fluid Reservoir 3 — Power Distribution Center 8 — Engine Oil Fill 4 — Brake Fluid Reservoir 9 —...
  • Page 409: Engine Compartment - 4.7L

    MAINTAINING YOUR VEHICLE 407 ENGINE COMPARTMENT – 4.7L 1 — Engine Coolant Reservoir 7 — Battery 2 — Automatic Transmission Dipstick 8 — Washer Fluid Reservoir 3 — Engine Oil Dipstick 9 — Engine Oil Fill 4 — Power Distribution Center 10 —...
  • Page 410: Engine Compartment - 5.7L

    408 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 5.7L 1 — Engine Coolant Reservoir 7 — Washer Fluid Reservoir 2 — Automatic Transmission Dipstick 8 — Engine Oil Dipstick 3 — Power Distribution Center 9 — Engine Oil Fill 4 — Brake Fluid Reservoir 10 —...
  • Page 411: Engine Compartment - 3.0L Diesel

    MAINTAINING YOUR VEHICLE 409 ENGINE COMPARTMENT – 3.0L DIESEL 1 — Engine Coolant Reservoir 6 — Washer Fluid Reservoir 2 — Power Distribution Center 7 — Engine Oil Fill 3 — Brake Fluid Reservoir 8 — Engine Oil Dipstick 4 — Integrated Power Module 9 —...
  • Page 412: Onboard Diagnostic System - Obd Ii

    410 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the “Malfunction Indica- diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic tor Light”...
  • Page 413: Emissions Inspection And Maintenance Programs

    MAINTAINING YOUR VEHICLE 411 manual). Tighten the gas cap until a clicking sound is EMISSIONS INSPECTION AND MAINTENANCE heard. This is an indication that the gas cap is properly PROGRAMS tightened. In some localities, it may be a legal requirement to pass an inspection of your vehicle’s emissions control system.
  • Page 414 412 MAINTAINING YOUR VEHICLE Your vehicle has a simple ignition key-actuated test, the ignition or start the engine. This means that your which you can use prior to going to the test station. To vehicle’s OBD II system is not ready and you should check if your vehicle’s OBD II system is ready, you must not proceed to the I/M station.
  • Page 415: Replacement Parts

    MAINTAINING YOUR VEHICLE 413 before going to the I/M station. The I/M station can fail NOTE: Intentional tampering with emissions control your vehicle because the MIL is on with the engine systems can result in civil penalties being assessed running. against you.
  • Page 416: Engine Oil

    414 MAINTAINING YOUR VEHICLE operate satisfactorily without periodic maintenance. (0.95L) of oil when the level is at the bottom of the SAFE However, if a malfunction of these items does occur, it range will result in the level being at the top of the SAFE could adversely affect the engine or vehicle performance.
  • Page 417 MAINTAINING YOUR VEHICLE 415 3.0L Diesel Engine Only American Petroleum Institute (API) Engine Oil Anytime the oil is drained and filled it is very important Identification Symbol to wait 15 minutes before starting the engine. This symbol means that the oil has been certified by the American Engine Oil Selection —...
  • Page 418 416 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (3.7L/4.7L/5.7L Engines) Engine Oil Viscosity (3.0L Diesel Engine) SAE 5W-20 engine oil is recommended for all operating CAUTION! temperatures. This engine oil improves low temperature starting and vehicle fuel economy. Your vehicle is equipped with an advanced technol- The engine oil filler cap also shows the recommended ogy Diesel Engine and an emission device designed engine oil viscosity for your vehicle.
  • Page 419: Engine Air Cleaner Filter

    MAINTAINING YOUR VEHICLE 417 The engine oil filler cap also shows the recommended indiscriminately discarded, can present a problem to the engine oil viscosity for your vehicle. For information on environment. Contact your local authorized dealer, ser- engine oil filler cap location, refer to “Engine Compart- vice station, or governmental agency for advice on how ment”...
  • Page 420: Maintenance-Free Battery

    418 MAINTAINING YOUR VEHICLE Maintenance-Free Battery WARNING! Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic main- The air induction system (air cleaner, hoses, etc) can tenance required. provide a measure of protection in the case of engine backfire.
  • Page 421: Air Conditioner Maintenance

    MAINTAINING YOUR VEHICLE 419 Air Conditioner Maintenance WARNING! (Continued) For best possible performance, your air conditioner • Battery posts, terminals and related accessories should be checked and serviced by an authorized dealer contain lead and lead compounds. Wash hands at the start of each warm season. This service should after handling.
  • Page 422: Body Lubrication

    420 MAINTAINING YOUR VEHICLE Body Lubrication WARNING! (Continued) Locks and all body pivot points, including such items as • The air conditioning system contains refrigerant seat tracks, door hinge pivot points and rollers, liftgate, under high pressure. To avoid risk of personal tailgate, sliding doors and hood hinges, should be lubri- injury or damage to the system, adding refrigerant cated periodically with a lithium based grease such as...
  • Page 423: Windshield Wiper Blades

    MAINTAINING YOUR VEHICLE 421 Windshield Wiper Blades The fluid reservoir for the windshield washers and the Clean the rubber edges of the wiper blades and the rear window washer is shared. The fluid reservoir is windshield periodically with a sponge or soft cloth and a located in the engine compartment, be sure to check the mild nonabrasive cleaner to remove accumulations of salt fluid level at regular intervals.
  • Page 424: Exhaust System

    422 MAINTAINING YOUR VEHICLE into the passenger compartment. In addition, inspect the WARNING! exhaust system each time the vehicle is raised for lubri- cation or oil change. Replace as required. Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care WARNING! must be exercised when filling or working around the washer solution.
  • Page 425 MAINTAINING YOUR VEHICLE 423 Under normal operating conditions, the catalytic con- NOTE: Intentional tampering with emissions control verter will not require maintenance. However, it is im- systems can result in civil penalties being assessed portant to keep the engine properly tuned to assure against you.
  • Page 426: Cooling System

    424 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter dam- Cooling System age: WARNING! • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in You or others can be badly burned by hot engine motion.
  • Page 427 MAINTAINING YOUR VEHICLE 425 accumulation of bugs, leaves, etc. If dirty, clean by gently Cooling System — Drain, Flush, And Refill spraying water from a garden hose vertically down the If the engine coolant (antifreeze) is dirty and contains a face of the condenser.
  • Page 428 426 MAINTAINING YOUR VEHICLE Adding Coolant CAUTION! Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance Mixing of engine coolant (antifreeze), other than the intervals. This engine coolant (antifreeze) can be used up specified HOAT engine coolant (antifreeze), may to 5 Years or 102,000 miles (170 000 km) before replace- result in engine damage and may decrease corrosion ment.
  • Page 429 MAINTAINING YOUR VEHICLE 427 • Mix a minimum solution of 50% HOAT engine coolant NOTE: Mixing engine coolant (antifreeze) types will (antifreeze) and distilled water. Use higher concentra- decrease the life of the engine coolant (antifreeze) and tions (not to exceed 70%) if temperatures below -34°F will require more frequent engine coolant (antifreeze) (-37°C) are anticipated.
  • Page 430 428 MAINTAINING YOUR VEHICLE rules for your community. To prevent ingestion by ani- WARNING! mals and children, do not store ethylene glycol-based • The warning words DO NOT OPEN HOT on the engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground.
  • Page 431 MAINTAINING YOUR VEHICLE 429 • Do not overfill the coolant recovery bottle. of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once • Check engine coolant (antifreeze) freeze point in the a month.
  • Page 432: Brake System

    430 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is WARNING! equipped with air conditioning, keep the front of the condenser clean. Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting •...
  • Page 433: Front/Rear Axle Fluid

    MAINTAINING YOUR VEHICLE 431 With disc brakes, the fluid level can be expected to fall as Use only brake fluid that has been in a tightly-closed the brake linings wear. However, an unexpected drop in container to avoid contamination from foreign matter or fluid level may be caused by a leak and a system check moisture.
  • Page 434: Transfer Case

    432 MAINTAINING YOUR VEHICLE Selection of Lubricant Drain Use only the manufacturer’s recommended fluid. Refer First remove fill plug, then remove drain plug. Recom- to “Fluids, Lubricants, and Genuine Parts” in this section mended tightening torque for drain and fill plugs is 15 to for correct fluid type.
  • Page 435: Automatic Transmission

    MAINTAINING YOUR VEHICLE 433 Automatic Transmission CAUTION! Selection of Lubricant Using a transmission fluid other than the manufac- It is important that the proper lubricant is used in the turer’s recommended fluid may cause deterioration transmission to assure optimum transmission perfor- in transmission shift quality and/or torque converter mance.
  • Page 436 434 MAINTAINING YOUR VEHICLE Fluid Level Check (3.7L and 3.0L Diesel Engine) CAUTION! (Continued) Regular fluid level checks are not required. For this • The fluid level is preset at the factory and it does reason, the dipstick is omitted. not require adjustment under normal operating If you notice fluid loss or shift lever malfunction, have conditions.
  • Page 437 MAINTAINING YOUR VEHICLE 435 2. The vehicle must be on level ground. NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be 3. Fully apply the parking brake, and press the brake between the two “COLD”...
  • Page 438: Maintenance After Off-Road Driving

    436 MAINTAINING YOUR VEHICLE To prevent dirt and water from entering the transmission Service Manual. Also check for accumulations of vegeta- after checking or replenishing fluid, make certain that the tion or brush that could become a fire hazard, or conceal dipstick cap is properly reseated.
  • Page 439 MAINTAINING YOUR VEHICLE 437 passable in snow and ice, and those that are sprayed on Washing trees and road surfaces during other seasons, are highly • Wash your vehicle regularly. Always wash your ve- corrosive to the metal in your vehicle. hicle in the shade using MOPAR Car Wash or a mild The following maintenance recommendations will enable car wash soap, and rinse the panels completely with...
  • Page 440 438 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is • Do not use abrasive or strong cleaning materials considered the responsibility of the owner. such as steel wool or scouring powder, which will •...
  • Page 441 MAINTAINING YOUR VEHICLE 439 Wheel and Wheel Trim Care MOPAR Spot & Stain Remover, if absolutely necessary. All wheels and wheel trim, especially aluminum and Do not use harsh cleaners or Armorall. Use MOPAR chrome-plated wheels should be cleaned regularly with a Total Clean to clean vinyl upholstery.
  • Page 442 440 MAINTAINING YOUR VEHICLE Glass Surfaces WARNING! All glass surfaces should be cleaned on a regular basis with MOPAR Glass Cleaner or any commercial Do not use volatile solvents for cleaning purposes. household-type glass cleaner. Never use an abrasive type Many are potentially flammable, and if used in cleaner.
  • Page 443: Fuses

    MAINTAINING YOUR VEHICLE 441 2. Dry with a soft tissue. Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use MOPAR Total Clean, a mild soap solution, or lukewarm water.
  • Page 444 442 MAINTAINING YOUR VEHICLE Cav- Cartridge Cav- Cartridge Mini-Fuse Description Mini-Fuse Description Fuse Fuse 10 Amp Htd Mirror (EBL) 10 Amp Final Drive Control Module (FDCM), Heater Ventilation/ 20 Amp Rr Pwr Out (B+) Air Conditioning Yellow (HVAC), Rear Heated 10 Amp Rr HVAC (R/O) Seat Switch, O/H,...
  • Page 445 MAINTAINING YOUR VEHICLE 443 Cav- Cartridge Cav- Cartridge Mini-Fuse Description Mini-Fuse Description Fuse Fuse 20 Amp Cigar Ltr (R/A) Spare Yellow (Acc De- lay) 10 Amp Tire Pressure Tran- sponders (R/O) 15 Amp Rear Wiper (B+) Blue 10 Amp Upper & Lower Switch Bank, Diag.
  • Page 446: Underhood Fuses (Power Distribution Center)

    444 MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Cav- Cartridge Mini-Fuse Description Fuse 40 Amp HID Headlamps Green 50 Amp PTC Heater 2 (Diesel Only) 30 Amp Power Outlets Pink 50 Amp PTC Heater 3 (Diesel Only) 30 Amp Cig Lighter, Trail Tow Pink Batt...
  • Page 447 MAINTAINING YOUR VEHICLE 445 Cav- Cartridge Cav- Cartridge Mini-Fuse Description Mini-Fuse Description Fuse Fuse — Spare 40 Amp Accessory Delay, Seats Green 40 Amp HVAC Blower Green 40 Amp JB Power Green 30 Amp Rear Wiper, Ign R/O Pink 30 Amp Wiper Motor Pink 40 Amp...
  • Page 448 446 MAINTAINING YOUR VEHICLE Cav- Cartridge Cav- Cartridge Mini-Fuse Description Mini-Fuse Description Fuse Fuse 15 Amp Brake Lamps — Spare Blue 20 Amp Trail-Tow Mod (Ex- 20 Amp HD Washer (If Yellow port Only) Yellow Equipped) (Export — Spare Only) 20 Amp Ignition Switch 30 Amp...
  • Page 449: Underhood Fuses (Integrated Power Module)

    MAINTAINING YOUR VEHICLE 447 Cav- Cartridge Cav- Cartridge Mini-Fuse Description Mini-Fuse Description Fuse Fuse 25 Amp Coils, Actuators 10 Amp Lt Park Lamps Natural — Spare 10 Amp Trailer-Tow Park Lamps Underhood Fuses (Integrated Power Module) 10 Amp Rt Park Lamps 20 Amp Front Control Module Yellow...
  • Page 450: Vehicle Storage

    448 MAINTAINING YOUR VEHICLE Cav- Cartridge Cav- Cartridge Mini-Fuse Description Mini-Fuse Description Fuse Fuse 20 Amp Rear Fog Lamps (Ex- 20 Amp Ignition Off Draw Yellow port Only) Yellow (IOD) #2 20 Amp Front Control Module 10 Amp Occupant Restraint Yellow (FCM) Batt #1 Controller (ORC) R/S...
  • Page 451: Replacement Bulbs

    MAINTAINING YOUR VEHICLE 449 air conditioning system at idle for about five minutes Exterior Lights Bulb Type in the fresh air and high blower setting. This will Backup Lights ......3157K ensure adequate system lubrication to minimize the Front Fog Lights .
  • Page 452: Bulb Replacement

    450 MAINTAINING YOUR VEHICLE BULB REPLACEMENT NOTE: On vehicles equipped with High Intensity Dis- charge Headlights (HID), when the headlights are turned High Intensity Discharge Headlights (HID) — If on, there is a blue hue to the lights. This diminishes and Equipped becomes more white after approximately 10 seconds, as The headlights are a type of high voltage discharge tube.
  • Page 453: Headlight

    MAINTAINING YOUR VEHICLE 451 Headlight 1. Open the hood. 2. Turn the low or high beam bulb one–quarter turn counterclockwise to remove from housing. 1 — High Beam Bulb 3 — Turn Signal Bulb 2 — Low Beam Bulb 3. Disconnect the electrical connector and replace the bulb.
  • Page 454: Front Turn Signal

    452 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Turn Signal 1.
  • Page 455: Front Fog Light

    MAINTAINING YOUR VEHICLE 453 CAUTION! CAUTION! Do not touch the new bulb with your fingers. Oil Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
  • Page 456: Rear Tail, Stop, Turn Signal, And Backup Lights

    454 MAINTAINING YOUR VEHICLE Rear Tail, Stop, Turn Signal, And Backup Lights 1. Raise the liftgate. 2. Remove the two Torx fasteners. 1 — Tail/Stop Light Bulb 3 — Back-Up Light Bulb 2 — Tail/Turn Signal Bulb 4. Pull the bulb to remove it from the socket. 3.
  • Page 457: Center High-Mounted Stop Light (Chmsl)

    MAINTAINING YOUR VEHICLE 455 Center High-Mounted Stop Light (CHMSL) 2. Twist the bulb socket to remove from the CHMSL housing. 1. Remove the two screws securing the CHMSL. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach the CHMSL.
  • Page 458: Fluids And Capacities

    456 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Metric Fuel (Approximate) 3.7/4.7/5.7L Gasoline Engines 21 Gallons 79 Liters 3.0L Diesel Engine 22 Gallons 83 Liters Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) 5 Quarts 4.7 Liters 4.7 Liter Engine (SAE 5W-20, API Certified) 6 Quarts 5.7 Liters...
  • Page 459 MAINTAINING YOUR VEHICLE 457 5.7 Liter Engine (MOPAR Engine Coolant/Antifreeze 5 16.7 Quarts 15.8 Liters Year/100,000 Mile Formula) — With Rear Heat 3.0 Liter Diesel Engine (MOPAR Antifreeze/Engine Coolant 5 13.9 Quarts 13.2 Liters Year/100,000 Mile Formula) — Without Rear Heat 3.0 Liter Diesel Engine (MOPAR Antifreeze/Engine Coolant 5 15.3 Quarts 14.5 Liters...
  • Page 460: Engine

    458 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Engine Oil (3.7L/4.7L/5.7L Engines) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
  • Page 461 MAINTAINING YOUR VEHICLE 459 Component Fluid, Lubricant, or Genuine Part Fuel Selection (3.7L and 4.7L Engine) 87 Octane Fuel Selection (5.7L Engine) 87 Octane Acceptable - 89 Octane Recommended Fuel Selection (3.0L Diesel Engine) Use good quality diesel fuel from a reputable supplier in your vehicle. The manufacturer requires that you must fuel this vehicle with Ultra Low Sul- fur Highway Diesel fuel (15 ppm Sulfur maximum) and prohibits the use of Low Sulfur Highway Diesel fuel (500 ppm Sulfur maximum) to avoid...
  • Page 462: Chassis

    460 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission MOPAR ATF+4 Automatic Transmission Fluid Transfer Case (NV140 Single Speed MOPAR ATF+4 Automatic Transmission Fluid Only) Transfer Case (NV245 Two Speed MOPAR NV 247/245 Transfer Case Lubricant Only) Axle Differential (Front-Rear) MOPAR Synthetic Gear &...
  • Page 463: Maintenance Schedules

    MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..462 Maintenance Schedule — Gasoline Engine . . 462 Maintenance Schedules ....462 Maintenance Schedule —...
  • Page 464 462 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULES The Scheduled Maintenance services listed in bold type Maintenance Schedule — Gasoline Engine must be done at the times or mileages specified to ensure The oil change indicator system will remind you that it is the continued proper functioning of the emissions control time to take your vehicle in for scheduled maintenance.
  • Page 465 MAINTENANCE SCHEDULES 463 if it has been 6 months since your last oil change even the vehicle is on level ground will improve the accu- if the oil change indicator message is NOT illumi- racy of the oil level reading. Add oil only when the nated.
  • Page 466 464 MAINTENANCE SCHEDULES At Each Oil Change Required Maintenance Intervals • Change the engine oil filter. NOTE: ** Vehicles built with the 4.7L engine are equipped with sixteen spark plugs, one set is located on • Inspect the brake hoses and lines. the top of the engine under the coils and the second set is located on the side of the engine.
  • Page 467 MAINTENANCE SCHEDULES 465 6,000 Miles (10,000 km) or 12,000 Miles (20,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil If using your vehicle for any of the following: Dusty or off-road conditions.
  • Page 468: Service Schedule

    466 MAINTENANCE SCHEDULES 18,000 Miles (30,000 km) or 24,000 Miles (40,000 km) or 30,000 Miles (50,000 km) or 18 Months Maintenance 24 Months Maintenance 30 Months Maintenance Service Schedule Service Schedule Service Schedule Change the engine oil and engine oil Change the engine oil and engine oil Change the engine oil and engine oil filter.
  • Page 469 MAINTENANCE SCHEDULES 467 36,000 Miles (60,000 km) or 42,000 Miles (70,000 km) or 48,000 Miles (80,000 km) or 36 Months Maintenance 42 Months Maintenance 48 Months Maintenance Service Schedule Service Schedule Service Schedule Change the engine oil and engine oil Change the engine oil and engine oil Change the engine oil and engine oil filter.
  • Page 470 468 MAINTENANCE SCHEDULES 54,000 Miles (90,000 km) or 60,000 Miles (100,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule Service Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil Replace the engine air cleaner filter.
  • Page 471 MAINTENANCE SCHEDULES 469 66,000 Miles (110,000 km) or 72,000 Miles (120,000 km) or 72 Months Maintenance Service 66 Months Maintenance Schedule Service Schedule Change the engine oil and engine oil filter. Rotate tires. Change the engine oil and engine oil If using your vehicle for any of the following: Dusty or off-road conditions.
  • Page 472 470 MAINTENANCE SCHEDULES 78,000 Miles (130,000 km) or 84,000 Miles (140,000 km) or 78 Months Maintenance 84 Months Maintenance Service Schedule Service Schedule Change the engine oil and engine oil Change the engine oil and engine oil filter. filter. Rotate tires. Rotate tires.
  • Page 473 MAINTENANCE SCHEDULES 471 90,000 Miles (150,000 km) or 90 Months Maintenance Service 96,000 Miles (160,000 km) or Schedule 96 Months Maintenance Change the engine oil and engine oil filter. Service Schedule Rotate tires. Change the engine oil and engine oil Replace the engine air cleaner filter.
  • Page 474 472 MAINTENANCE SCHEDULES 102,000 Miles (170,000 km) or 108,000 Miles (180,000 km) or 114,000 Miles (190,000 km) or 102 Months Maintenance 108 Months Maintenance 114 Months Maintenance Service Schedule Service Schedule Service Schedule Change the engine oil and engine oil Change the engine oil and engine oil Change the engine oil and engine oil filter.
  • Page 475 MAINTENANCE SCHEDULES 473 120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the ignition cables (3.7L Engine). Replace the top row of spark plugs (4.7L Engine). Replace the spark plugs (3.7L and 5.7L Engines).
  • Page 476 474 MAINTENANCE SCHEDULES 126,000 Miles (210,000 km) or 132,000 Miles (220,000 km) or 138,000 Miles (230,000 km) or 126 Months Maintenance 132 Months Maintenance 138 Months Maintenance Service Schedule Service Schedule Service Schedule Change the engine oil and engine oil Change the engine oil and engine oil Change the engine oil and engine oil filter.
  • Page 477 MAINTENANCE SCHEDULES 475 144,000 Miles (240,000 km) or 144 Months Maintenance Service 150,000 Miles (250,000 km) or Schedule 150 Months Maintenance Change the engine oil and engine oil filter. Service Schedule Rotate tires. Change the engine oil and engine oil If using your vehicle for any of the following: Dusty or off-road conditions.
  • Page 478 476 MAINTENANCE SCHEDULES † This maintenance is recommended by the manufacturer Chrysler LLC recommends that these maintenance inter- to the owner, but is not required to maintain emissions vals be performed at your selling dealer. The technicians warranty. at your dealership know your vehicle best, and have access to factory trained information, genuine MOPAR WARNING! parts, and specially designed electronic and mechanical...
  • Page 479 MAINTENANCE SCHEDULES 477 • Check the windshield washer solvent and add if • Inspect for the presence of water in the fuel filter/ required. water separator unit. Once a Month CAUTION! • Check tire pressure and look for unusual wear or Failure to perform the required maintenance items damage.
  • Page 480 478 MAINTENANCE SCHEDULES 6,250 Miles (10,000 km) or 12,500 Miles (20,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule Schedule Change the engine oil and engine oil filter. Rotate tires. Rotate tires. If you are using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary.
  • Page 481 MAINTENANCE SCHEDULES 479 18,750 Miles (30,000 km) or 25,000 Miles (40,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule Service Schedule Change the engine oil and engine oil filter. Rotate tires. Rotate tires. Replace the engine air cleaner filter. Inspect the front and rear axle fluid.
  • Page 482 480 MAINTENANCE SCHEDULES 31,250 Miles (50,000 km) or 37,500 Miles (60,000 km) or 43,750 Miles (70,000 km) or 30 Months Maintenance 36 Months Maintenance 42 Months Maintenance Service Schedule Service Schedule Service Schedule Rotate tires. Change the engine oil and engine oil Rotate tires.
  • Page 483 MAINTENANCE SCHEDULES 481 50,000 Miles (80,000 km) or 48 Months Maintenance Service 56,250 Miles (90,000 km) or Schedule 54 Months Maintenance Change the engine oil and engine oil filter. Service Schedule Rotate tires. Rotate tires. Replace the engine air cleaner filter. Inspect the front and rear axle fluid.
  • Page 484 482 MAINTENANCE SCHEDULES 62,500 Miles (100,000 km) or 60 Months Maintenance Service 68,750 Miles (110,000 km) or Schedule 66 Months Maintenance Change the engine oil and engine oil filter. Service Schedule Rotate tires. Rotate tires. If you are using your vehicle for any of the following: Dusty or off-road conditions. Inspect the engine air cleaner filter, replace if necessary.
  • Page 485 MAINTENANCE SCHEDULES 483 75,000 Miles (120,000 km) or 72 Months Maintenance Service 81,250 Miles (130,000 km) or Schedule 78 Months Maintenance Change the engine oil and engine oil filter. Service Schedule Rotate tires. Rotate tires. Replace the engine air cleaner filter. Replace the fuel filter/water separator unit.
  • Page 486 484 MAINTENANCE SCHEDULES 87,500 Miles (140,000 km) or 93,750 Miles (150,000 km) or 84 Months Maintenance 90 Months Maintenance Service Schedule Service Schedule Change the engine oil and engine oil Rotate tires. filter. Inspect the front and rear axle fluid. Rotate tires.
  • Page 487 MAINTENANCE SCHEDULES 485 100,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule Change the engine oil and engine oil filter. Rotate tires. Replace the engine air cleaner filter. Replace the fuel filter/water separator unit. Inspect the front suspension, tie rod ends and boot seals, replace if necessary. Inspect the brake linings, replace if necessary.
  • Page 488 486 MAINTENANCE SCHEDULES WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
  • Page 489: If You Need Consumer Assistance

    IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Customer Assistance For The Hearing Or Vehicle......489 Speech Impaired (TDD/TTY) .
  • Page 490 488 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....493 Traction Grades ..... 495 Department Of Transportation Uniform Tire Temperature Grades .
  • Page 491: Suggestions For Obtaining Service For Your Vehicle

    IF YOU NEED CONSUMER ASSISTANCE 489 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
  • Page 492: Chrysler Llc Customer Center

    490 IF YOU NEED CONSUMER ASSISTANCE • Vehicle delivery date and mileage This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- Chrysler LLC Customer Center solved with this process. P.O. Box 21–8004 •...
  • Page 493: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)

    IF YOU NEED CONSUMER ASSISTANCE 491 Customer Assistance For The Hearing Or Speech have any questions about the service contract, call the Impaired (TDD/TTY) manufacturer’s Service Contract National Customer Hot- To assist customers who have hearing difficulties, the line at 1-800-521-9922. manufacturer has installed special TDD (Telecommuni- The manufacturer will not stand behind any service cation Devices for the Deaf) equipment at its customer...
  • Page 494: Warranty Information (U.s. Vehicles Only)

    492 IF YOU NEED CONSUMER ASSISTANCE the ownership experience. You’ll be pleased with their MOPAR PARTS sincere efforts to resolve any warranty issues or related Mopar fluids, lubricants, parts, and accessories are concerns. available from an authorized dealer. They will help keep the vehicle operating at its best.
  • Page 495: In Canada

    IF YOU NEED CONSUMER ASSISTANCE 493 To contact NHTSA, you may either call the Auto Safety PUBLICATION ORDER FORMS Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– 9153), To order the following manuals, you may use either the or go to http://www.safercar.gov; or write to: Adminis- website or the phone numbers listed below.
  • Page 496 494 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Call toll free at: • 1–800–890–4038 (U.S.) Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- • 1–800–387–1143 (Canada) cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
  • Page 497 IF YOU NEED CONSUMER ASSISTANCE 495 Treadwear WARNING! The Treadwear grade is a comparative rating, based on the wear rate of the tire when tested under controlled The traction grade assigned to this tire is based on conditions on a specified government test course. For straight-ahead braking traction tests, and does not example, a tire graded 150 would wear one and one-half include acceleration, cornering, hydroplaning, or...
  • Page 498 496 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel, than the minimum required by law. WARNING! The temperature grade for this tire is established for a tire that is properly inflated and not overloaded.
  • Page 499 INDEX I n f o r m a t i o n P r o v i d e d b y :...
  • Page 500 498 INDEX ABS (Anti-Lock Brake System) ....309 Antifreeze (Engine Coolant) ....456 Adding Fuel .
  • Page 501 INDEX 499 Torque Converter ..... . 294 Parking ......308 Autostick .
  • Page 502 500 INDEX Light ....... 167 Climate Control ......261 Luggage Carrier .
  • Page 503 INDEX 501 Drain, Flush, and Refill ....425 Dipsticks Inspection ......424 Automatic Transmission .
  • Page 504 502 INDEX Electrical Outlet, Auxiliary (Power Outlet) ..163 Emission Control System Maintenance ..411,462 Electronic Brake Control System ... . . 312 Engine Anti-Lock Brake System .
  • Page 505 INDEX 503 Overheating ......390 Hazard Warning ..... . . 390 Starting .
  • Page 506 504 INDEX Fog Lights ..... . . 135,192,453 Fuel, Flexible ... . . See Flexible Fuel Vehicles Folding Rear Seat .
  • Page 507 INDEX 505 Gross Vehicle Weight Rating ... . . 367,369 Hitches GVWR ....... 367 Trailer Towing .
  • Page 508 506 INDEX Interior Appearance Care ....439 Lap/Shoulder Belts ..... . . 37 Interior Fuses .
  • Page 509 INDEX 507 Bulb Replacement ..... . 450 Instrument Cluster ....130,134 Cargo .
  • Page 510 508 INDEX Traction Control ..... . . 325 Maintenance Procedures ....413 Turn Signal .
  • Page 511 INDEX 509 Mopar Parts ......413,492 Filter Disposal ......417 Multi-Function Control Lever .
  • Page 512 510 INDEX Park Sense System, Rear ....147 Sunroof ......160 Parking Brake .
  • Page 513 INDEX 511 Rear Heated Seats ..... . . 120 Remote Sound System (Radio) Controls ..258 Rear Park Sense System .
  • Page 514 512 INDEX Safety Information, Tire ....326 Cleaning ......439 Safety Tips .
  • Page 515 INDEX 513 Service Manuals ......493 Automatic Transmission ....280 Setting the Clock .
  • Page 516 514 INDEX Sunglasses Storage ..... . . 154 Tire Markings ......326 Supplemental Restraint System - Airbag .
  • Page 517 INDEX 515 Safety ......326 Trailer Towing ......369 Sizes .
  • Page 518 516 INDEX Transmitter, Remote Keyless Entry (RKE) ..21 Video Entertainment System™ Tread Wear Indicators ....340 (Rear Seat Video System) .
  • Page 519 INDEX 517 Windshield Defroster ....71,263,269 Windshield Wipers ..... . . 139 Windshield Washers .
  • Page 520 INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
  • Page 521 Chrysler LLC 81-326-0954 Second Edition Printed in U.S.A. I n f o r ma t i o n P r o v i d e d b y :...

This manual is also suitable for:

2011 grand cherokee

Table of Contents

Save PDF