Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miranda SPG-1801
Summary of Contents for Miranda SPG-1801
- Page 1 DENSITÉ series SPG-1801 Sync Pulse Generator Module Guide to Installation and Operation M845-9800-100 13 Jul 2007 Miranda Technologies Inc. 3499 Douglas-B.-Floreani St-Laurent, Québec, Canada H4S 1Y6 Tel. 514-333-1772 Fax. 514-333-9828 www.miranda.com © 2007 Miranda Technologies Inc..
- Page 2 EN 61000-3-2 & -3-3, Disturbance in Supply Systems EN 61000-4-2, -3, -4, -5, -6, -8 & -11 Electromagnetic Immunity How to contact us: For technical assistance, please contact the Miranda Technical support centre nearest you: Europe, Middle East, Americas Asia...
-
Page 3: Table Of Contents
GUIDE TO INSTALLATION AND OPERATION Table of Contents SPG-1801 Sync Pulse Generator Module.................4 Introduction ............................4 Features .............................. 4 Block Diagram............................. 4 Card Front Edge Layout........................5 Application............................5 Installation ..........................6 Unpacking ............................6 Installation in the Densité frame......................6 Connection ............................ -
Page 4: Spg-1801 Sync Pulse Generator Module
1 SPG-1801 Sync Pulse Generator Module 1.1 Introduction The SPG-1801 is a sync pulse generator that can be slotted in the Densité frame. It accepts an external reference input or can receive its reference from the frame reference internal distribution, if the REF-1801 card is present. -
Page 5: Card Front Edge Layout
Status LED 1.5 Application One interesting application of the SPG-1801 combines the URS4D signal that is distributed to all Densité slots within the same frame from an REF-1801 card in slot 10, with multiple dual-independent-output SPG- 1801 cards to create a multi-format audio/video reference generation system. -
Page 6: Installation
2.2 Installation in the Densité frame The SPG-1801 must be mounted in a DENSITÉ-2 frame. The installation includes both the SPG-1801 module, and the rear panel module. It is not necessary to switch off the frame’s power when installing or removing the card. -
Page 7: Operation
3.2 Local control using the Densité frame control panel Push the SELECT button on the SPG-1801 card edge (see Section 1.4) to assign the local control panel to operate the SPG-1801. Use the control panel buttons to navigate through the menu, as described below. -
Page 8: Status Led
3.2.1 Status LED The status monitor LED is located on the front card-edge of the SPG-1801, and is visible through the front access door of the DENSITÉ frame. This multi-color LED indicates module status by color, and by flashing/steady illumination, according to the chart. The chart also indicates fault reporting for this card on the DENSITÉ... -
Page 9: Menu For Local Control
The SPG-1801 has operating parameters which may be adjusted locally at the controller card interface. After pressing the SELECT button on the SPG-1801 module, use the keys on the local control panel (described above) to step through the displayed menu and adjust the parameters. The menu is shown below. -
Page 10: Remote Control Using Icontrol
The basic window structure for the SPG-1801 is shown in figure 3.1. The window identification line at the top gives the card type (SPG-1801), and the slot number in which the card is installed in the Densité frame. On the left is a Status icon for the card. -
Page 11: Input Tab
2. Tabs are provided to give access to the various controls. Click on a tab to access it 3. The contents of the selected tab, with operating controls and status monitors as required. 4. The Load Factory button. Clicking this button will reset all SPG-1801 parameters to factory-default values, overriding settings made in the control panels. 3.3.2... -
Page 12: Output Tab
TC (URS) – use the timecode included in the URS signal. generated by an REF-1801 card located in slot 10 of the Densité frame The current status of time code available at the SPG-1801 input is shown in the LTC Status, VITC Status and TC (URS) Status areas •... -
Page 13: Alarms Tab
• • Word Clock 48 kHz Vertical (lines) – the slider selects the vertical offset between the reference input to the SPG-1801 and the output being configured. • The nominal range is +/- one frame, and is indicated (in lines) at the ends of the slider •... - Page 14 The alarm exists but has no effect (used for text and composite alarms) Shortcut: if you click in one of the columns beside SPG-1801 in the Status/Name column (where there is no pulldown shown), you will open an “invisible” pulldown that lets you assign a level to all alarms in that column simultaneously.
- Page 15 OK accepts the settings and closes the window once the card confirms that there are no errors. • Apply accepts the settings, but leaves the window open • Cancel closes the window without applying any changes, and leaves the previous settings intact. SPG-1801 | 15...
-
Page 16: Info Tab
GUIDE TO INSTALLATION AND OPERATION 3.3.5 Info tab When the SPG-1801 is included in an iControl environment, certain information about the card should be available to the iControl system. The user can enter labels and comments that will make this card easy to identify in a complex setup. - Page 17 • Remote System Administration – opens the Joining Locators window, which lists remote lookup services to which this SPG-1801 is registered. Add: Force the iControl service for this SPG-1801 to register itself on a user-specified Jini lookup service, using the following syntax for the locator’s URL in the Input data box: jini://<ip_address>...
-
Page 18: Specifications
ANALOG REFERENCE OUTPUT SIGNAL TYPE Composite NTSC-M, PAL-B with optional VITC STANDARD SMPTE-170M, ITU-R BT.1700-1, SMPTE-318M SIGNAL LEVEL 1V p-p RETURN LOSS > 35dB up to 10MHz SIGNAL TYPE HD Tri-Level Sync STANDARD SMPTE-274M, SMPTE-296M SIGNAL LEVEL 600mV p-p 18 | SPG-1801... - Page 19 GUIDE TO INSTALLATION AND OPERATION SIGNAL TYPE DARS AES-3id STANDARD SMPTE-276M SIGNAL LEVEL 1V p-p SIGNAL TYPE Word Clock STANDARD AES11-2003 SIGNAL LEVEL 2.0V p-p OTHER MAXIMUM POWER PHYSICAL FORMAT Densité-2 SPG-1801 | 19...
Need help?
Do you have a question about the SPG-1801 and is the answer not in the manual?
Questions and answers