Advertisement
29.
Check that you
removed all the shipping pieces, including
the round shipping piece. Dispose of all
materials in proper manner.
If you do not remove the round shipping
piece, your washer/dryer may "walk" away
from its location.
30.
Check that you have all
your tools.
31.
Turn on water faucets and
check for leaks. Tighten couplings if there is
leaking. DO NOT OVERTIGHTEN. This could
cause damage to faucets.
32.
Replace the access panel. Be
sure to tighten screws at each end of the
access panel.
33.
Plug power supply cord into
grounded outlet.
34.
Read the Use and Care Guide
to fully understand your new washer/dryer.
Now start the washer and allow it to
complete the regular cycle.
35.
Remove tape from dryer door
and open dryer door. Remove tape across
the dryer lint screen. Check to be sure lint
screen is in its proper position. Wipe out drum
with a damp cloth to remove any dust. Start
dryer and allow it to complete a heat cycle
to make sure the dryer is working properly.
36.
Finally, save all literature and
keep with washer/dryer.
You have just
finished installing your
new washer/dryer.
To get the most efficient use from
your new washer/dryer, read
your Use & Care Guide.
Congratulations!
Keep Installation Instructions nearby
where you can refer to them.
They'll make reinstalling
your washer/dryer in
another home as easy as
the first installation.
Panel E
Recessed and closet
installation
instructions
!
!
WARNING
Fire Hazard
It is recommended that the washer/dryer be
exhausted to the outside.
If washer/dryer is installed in a closet, the
dryer MUST be exhausted outside.
Failure to follow these instructions may
result in a fire.
To prevent large amounts of lint and moisture
from accumulating and to maintain drying
efficiency, and to prevent exposure to
possible health hazards, this appliance
should be exhausted outdoors.
THIS WASHER/DRYER MAY BE INSTALLED
IN A RECESSED AREA OR CLOSET.
The installation spacing is in centimeters and
inches and is the minimum allowable.
Additional spacing should be considered for
ease of installation, servicing and
compliance with local codes and
ordinances.
If closet door is installed, the minimum
unobstructed air openings in top and
bottom are required. Louvered doors with
equivalent air openings are acceptable.
Closet installation must be exhausted.
Other installations must use the minimum
dimensions indicated.
Recessed installation
0 cm (0")
0 cm (0")
30.5 cm
(12")
dryer
washer
front view
Minimum installation spacing
Note: If recessed installation is exhausted, all
spacing can be 0 cm (0 in).
Additional clearance for wall, door and floor
molding may be required.
Closet installation
closet door
310 sq. cm (48 sq. in.)
7.6 cm (3")
7.6 cm (3")
155 sq. cm (24 sq. in.)
front view
Unobstructed air openings are minimum for closet
door. Louvered door with equivalent air openings
is acceptable.
310 sq. cm (48 sq. in.)
closet door
155 sq. cm (24 sq. in.)
2.5 cm (1")
side view
Closet installation must be exhausted outdoors.
Recessed, non-exhausted installation must use
only the rear exhaust position and Exhaust
Deflector Kit No. 4500 is required.
Product dimensions
(Shown with legs extended 1 inch from
bottom of washer/dryer.)
30.5 cm
(12")
11.1 cm
(4-3/8")
recess
depth
70.2 cm
(27-5/8")
7.6 cm (3")
144.8 cm
119.4 cm
(57")
130.9 cm
(51-1/2")
side view
0 cm (0")
Additional
space may
be needed
for exhaust
61 cm
(24")
3.8 cm
(1-1/2")
exhaust
outlet
96.5 cm
cold
drain
water inlet
69.9 cm
72.7 cm
(27-1/2")
(28-5/8")
36.2 cm
(14-1/4")
recess width
48.3 cm
(19")
rear view
side view
39.1 cm
(15-3/8")
54.1 cm
(21-5/16")
(47")
81.6 cm
(32-1/8")
69.2 cm
(27-1/4")
(38")
13.3 cm
(5-1/4")
182.2 cm
(71-3/4")
96.5 cm
(38")
Advertisement
