HP S7650 SERVICE MANUAL 17’’ CDT MONITOR HP S7650 THESE DOCUMENTS ARE FOR REPAIR SERVICE INFORMATION ONLY. EVERY REASONABLE EFFORT HAS BEEN MADE TO ENSURE THE ACCURACY OF THIS MANUAL; WE CANNOT GUARANTEE THE ACCURACY OF THIS INFORMATION AFTER THE DATE OF PUBLICATION AND DISCLAIMS LIABILITY FOR...
HP S7650 Revision List Version Date Revision History TPV Model Name Initial Release P784B-2 Sep.-13-04 Update Schematic Diagram,BOM P784BVCCHPN2P Nov.23-23-05 Update BOM P784BVCCHPN2 Jan.-12-2006...
HP S7650 2. Precautions And Notices 2-1 Safety Precautions Observe all caution and safety related notes located inside the display cabinet. Operation of the display with the cover removed, may cause a serious shock hazard from the display power supply. Work on the display should not be attempted by anyone who is not thoroughly familiar with precautions necessary when working on high voltage equipment.
HP S7650 2-3 Service Notes When replacing parts or circuit boards, clamp the lead wires around terminals before soldering. When replacing a high wattage resistor (more than 1/2W of metal oxide film resistor) in circuit board, keep the resistor about 10mm (1/2 in) away from circuit board.
HP S7650 3. Operating Instructions This procedure gives you instructions for installing and using the Color display. Position the display on the desired operation and plug the power cord into a convenient AC outlet. Three-wire power cord must be shielded and is provided as a safety precaution as it connects the chassis and cabinet to the electrical conduit ground.
HP S7650 4. Adjustment 4-1 Adjustment Conditions And Precautions Approximately 30 minutes should be allowed for warm up before proceeding. Adjustments should be undertaken only on those necessary elements since most of them have been carefully preset at the factory.
Page 10
HP S7650 H-Size H-Moire Reduce H-Center Moire Disable V-Size No Use V-Center No Use Pincushion No Use Parallelogram V-Linearity Pin-Balance V-Linearity Trapezoid Top Corner Rotation Bot Corner No Use No Use Contrast Max-Hsize Modify Brightness Max-Vsize Modify R-Bias Max-Trapezoid Modify...
Page 11
HP S7650 (b) To make the adjustment condition is under the Factory preset OSD menu. Same as step 2-B. (c) Warm up more than 20 minutes. (d) Put the probe in the middle of screen, Brightness set to maximum. Contrast set to max.
Page 12
HP S7650 C. Produce a complete, red pattern on the display. Adjust the purity magnet rings on the PCM assembly to obtain a complete field of the color red. This is done by moving the two tabs in such a manner that they advance in an opposite direction but at the same time to obtain the same angle between the two tabs, which should be approximately 180'.
HP S7650 5. Circuit Description 5-1 Micro Controller Circuit MICRO Controller The IC101 contains a 6502/8051 8-bit CPU core, 512 bytes of RAM, 16K bytes of ROM,14 channel 8 bit PWM D/A converters, 2 channel A/D converters for key detection, one 8 bit pre-loadable...
HP S7650 Pin28 (BDRV) is floating Pin26 (HDRV) is floating Vertical Oscillator The vertical free –running frequency is determined by the capacitance C613 at pin22. Usually the free-running frequency should be lower than the minimum trigger frequency. 5-3 Transistor & Diode Circuit...
HP S7650 6.Trouble Shooting Chart 6-1 No Raster 1. CRT Relative Circuit Problems CHECK MAIN PCB POWER SUPPLY 47.0V,13V CHECK POWER SAVING CIRCUIT, H-SYNC, V-SYNC SIGNAL Q909, Q910 CHECK THE HIGE VOLTAGE OF CRT REFER ITEM S.M.P.S. ABOUT 23~24KV CHECK FAILSAFE CKT IC401 PIN 25 RELATIVE CKT.
Page 16
HP S7650 2.Abnormal Video Level On Screen 3. Abnormal DDC (Plug & Play)
HP S7650 6-5 Abnormal Horizontal Deflection 1.Abnormal Horizontal Width Of Video 2.Abnormal Horizontal Video Center CHECK IC401 PIN 4, 7 RELATIVE CIRCUIT 3.Abnormal Horizontal Linearity...