Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for 12Volt DirectStart CS423
- Page 1 CS400 DIRECTSTART REMOTE CAR STARTER + ALARM CS423 DIRECTSTART REMOTE CAR STARTER w/ 3 ZONE INTRUSION ALARM OPTIONS INSTALLATION MANUAL DIRECTSTART MANUFACTURED FOR 12VOLT DIRECT Div. Of TRILOGIX ELECTRONIC SYSTEMS INC. www.12voltdirect.com CS400 VERSION 412...
-
Page 2: System Contents
CS400 DIRECTSTART REMOTE CAR STARTER + ALARM INSTALLATION INFO System Wiring Transmitter Programming: How to System Programming: How to, Example, Bank I Programming: Basic features. Bank II Programming: Remote start features Tach Programming: Tach Setting, Adjusting, Engine Crank Protection Diesel Installation: Description of Options Safety device Connections: Automatic &... -
Page 3: Tach Programming
CS400 DIRECTSTART REMOTE CAR STARTER + ALARM TACH PROGRAMMING (MANDATORY) *NOTE THIS IS THE FIRST THING YOU SHOULD DO AFTER ALL WIRE CONNECTIONS HAVE BEEN MADE. At least one transmitter must be programmed inorder to proceed with TACH programming. If transmitter is not programmed proceed to Transmitter programming (page #4) then return to complete tach programming first before changing any function settings or adding additional transmitters To enter Tach Programming:... - Page 4 CS400 DIRECTSTART REMOTE CAR STARTER + ALARM TRANSMITTER TRANSMITTER TRANSMITTER TRANSMITTER (Description & Operation) (Description & Operation) (Description & Operation) (Description & Operation) BUTTON #1 "LOCK" Icon Button #I (Lock Icon) is used to LOCK (Optional) electric door locks and/or ARM engine interrupt circuit and/or intrusion alarm.
-
Page 5: Changing Function Settings
CS400 DIRECTSTART REMOTE CAR STARTER + ALARM CHANGING FUNCTION SETTINGS TO ENTER FUNCTION PROGRAMMING YOU REPEAT THE TRANSMITTER PROGRAMMING SEQUENCE: 1. Open the hood. (J2-PIN#14 Violet hood switch wire must see (-) ground ) 2. Toggle the Ignition Key ON and OFF 8 times…(Start and Finish in the OFF position) Parklights will come on solid to indicate system is in Transmittter learning mode. - Page 6 CS400 DIRECTSTART REMOTE CAR STARTER + ALARM BANK BANK BANK BANK 1 1 1 1 PROGRAMMING PROGRAMMING PROGRAMMING PROGRAMMING FUNCTIONS FUNCTIONS FUNCTIONS FUNCTIONS OPTIONS OPTIONS OPTIONS OPTIONS 1 - Door lock Option 1 :: Active door lock Button 2 : Passive door lock (Doors/Alarm lock w/ Interrupt Circuit) Button 3 : Erase all learned code and reset to original default Note Option #3 will (A) erase all transmitters.
- Page 7 CS400 DIRECTSTART REMOTE CAR STARTER + ALARM BANK BANK BANK BANK 2 2 2 2 PROGRAMMING PROGRAMMING PROGRAMMING PROGRAMMING FUNCTIONS FUNCTIONS FUNCTIONS FUNCTIONS OPTIONS OPTIONS OPTIONS OPTIONS 1- Fuel setting/ Option 1 : Gasoline engine Diesel timeout Option 2 : Diesel engine 12 sec. Glow-Plug time-out Option 3 : Diesel engine, Glow-plug monitor on brake input J2-PIN#12 (Green)~ 2- Groundout...
- Page 8 CS400 DIRECTSTART REMOTE CAR STARTER + ALARM Parking Light Status (Flash Codes) #Flash Rate Description fast Doors Lock; Armed; End of run time; Exiting Service mode slow Cold weather mode canceled;Low voltage start cancelled fast Doors Unlock; Disarm Disabler; Entering Service mode slow Power-up reset automatic transmission Car in Ready mode (manual transmission mode only)
- Page 9 CS400 DIRECTSTART REMOTE CAR STARTER + ALARM WIRE HARNESS DESCRIPTION J1: 6 PIN MAIN WIRING HARNESS PIN# PIN# PIN# PIN# COLOR COLOR COLOR COLOR POLARITY POLARITY POLARITY POLARITY DESCRIPTION DESCRIPTION DESCRIPTION DESCRIPTION J1-PIN#1- RED(30A FUSE) : + 12 VDC Main Power Source Input : Connect the Red wire to main constant +12 VDC power source or to the positive terminal of the battery.
- Page 10 CS400 DIRECTSTART REMOTE CAR STARTER + ALARM WIRE HARNESS DESCRIPTION J2-PIN#6 BROWN NEGATIVE STARTER KILL 500 mA Negative Output FUNCTION 2 -Connect this Brown wire to Pin 86 of the Starter Interrupt Relay. Programmable for: Option 1 : Active Arming (Transmitter must be used to Arm & Disarm system) Option 2 : Passive Arming (will arm automatically 30 sec.
-
Page 11: Manual Transmission Vehicles
CS400 DIRECTSTART REMOTE CAR STARTER + ALARM MANUAL TRANSMISSION VEHICLES INSTALLATION & OPERATING INSTRUCTIONS It is essential that ALL Safety connections are installed, tested and functioning properly for safe operation. It is essential that ALL Safety connections are installed, tested and functioning properly for safe operation. It is essential that ALL Safety connections are installed, tested and functioning properly for safe operation.