Summary of Contents for Icom MarineCommander MXP-5000
Page 1
INSTRUCTION MANUAL MARINE PLOTTER MXP-5000 DISPLAY UNIT MXD-5000 This device complies with Part 15 of the FCC Rules. Opera- tion is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United CAUTION: Changes or modifications to these Kingdom, Germany, France, Spain, Russia and/or other countries.
FCC INFORMATION ·················································· i TABLE OF CONTENTS ············································· ii PRECAUTIONS ························································ iii 1 PANEL DESCRIPTION ······································1–5 ■ Main unit (MXP-5000) ·········································1 ■ Display unit (MXD-5000) ····································2 2 INSTALLATION AND CONNECTIONS ···········6–11 ■ Connection ·························································6 ■ Mounting the Main unit ·······································7 ■...
Display extension unit away from heavy rain, and never immerse it in the water. The Display extension unit meets IPX4 requirements For MXP-5000 (Main unit): for splash resistance when the connection cables are R WARNING! NEVER apply AC voltage to the DC connected.
GPS, Com- e DATA IN/OUT CONNECTOR [DATA IN/OUT] pass and STW. Connect an Icom AIS Transponder, Marine VHF transceiver or navigation equipment. o HEADING CONNECTOR [HEADING] See page 14 for the [DATA IN/OUT] connector infor- Connect a heading sensor.
PANEL DESCRIPTION ■ MXD-5000 (Display unit) D Front panel BRILL RANGE FOCUS LAYOUT MENU CLEAR q POWER/DISPLAY BRILLIANCE SWITCH r FOCUS/DISPLAY LAYOUT SWITCH [ /BRILL] [FOCUS/LAYOUT] ➥ Push to change the active screen. • While the MarineCommander’s power is OFF •...
Page 7
While opening the Menu screen, push to cancel chart* by JEPPESEN. and return to the upper menu, or cancel the Menu * Chart data is not supplied by Icom. screen. • An unmount operation should be performed before removing the SD Card. If you do not unmount the SD...
Page 8
(Default: Position) the vessel. Shows the current position data* in latitude/longi- When a companion Icom fish finder is not connected tude. to the main unit, or the sea bottom is not detected, * Depending on the presetting, Loran-C Time differences “–––”...
Page 9
!4 !3 !2 u STATUS-BAR !1 FISH FINDER ICON ➥ Shows the status data. Display as an animation when a companion Icom ➥ • A total of 19 options are selectable. fish finder is connected and operating. The selectable options are Date/Time, Position, COG/ Appears, but not as an animation, when the fish ➥...
DC IN EXT-DISPLAY DATA IN/OUT MAIN Ground Main unit DC IN Thinner Black CAUTION: NEVER connect (MXP-5000) 12V/24V or disconnect the display Green cable/display extension unit while turning ON the power. 12 V/24 V battery Black 5 m; 16.4 ft...
(3.28 ft) away from your vessel’s magnetic navigation compass. Bolt Spring washer Flat washer First, drill six φ5.5–6 mm (0.22–0.24 in) holes to mount the MXP-5000. Flat washer Spring washer ■ Power source requirement ■ Ground connection CAUTION: Before connecting the DC power cable, To prevent electrical shocks and other problems, check the following important items.
INSTALLATION AND CONNECTIONS ■ Installing the Display unit D Mounting D Location The mounting bracket supplied with the display unit al- Select a place for installation which meets the follow- lows “dashboard” or “overhead” mounting. ing important conditions: q Hold the mounting bracket up to the selected loca- ➥...
Page 13
INSTALLATION AND CONNECTIONS D Wall mounting The display unit can be mounted to a flat surface, such as an instrument panel, using the mounting bolts (M6 × 35 mm). Flat washer Spring washer q Remove the four bolts from the four corners of the display unit.
INSTALLATION AND CONNECTIONS ■ Front cover attachment The supplied front cover can be attached to the front of the display unit. Front cover ■ Bolt cap attachment The supplied bolt caps can be attached to the four corner bolts to protect them from dust and moisture.
INSTALLATION AND CONNECTIONS ■ Removing or connecting the EX-3187’s cable To install the display cable though a hole in a wall BE CAREFUL! The EX-3187 meets IPX4 require- where as the display connector cannot pass through ment for splash resistant when the connecting the the hole, remove the cable from the EX-3187 or the connection cables.
Allows you to install the Main unit and Display unit mal performance when used with Icom equipment. up to 20 m (65.6 ft) apart. (one Display cable+three Icom is not responsible for the destruction or damage to EX-3187s) Icom equipment in the event the Icom equipment is used •...
D MXD-5000 (Display unit) • LCD display : 12.1-inch SVGA Color display • DC input voltage : 30 V DC supplied from MXP-5000 (Main unit) • Power consumption : Less than 1.0 A (at maximum brightness) • Usable temperature range : –20°C to +60°C;...
HEADING IN Red 2 (with 2 V applied) Pink bps and 19200 bps. (Default: 4800 bps) (– –) Connects to the Icom MA-500TR or to the Icom MXA-5000 or to an AIS receiver. Black 1 Yellow AIS-2 IN (–) (IEC61162-2) (–)