Advertisement
Quick Links
Important Steps that Make Your Printer
Work with Your System
To make your new Model 3321 Invoice Printer work with your Hardlines & Lumber system, you need
to make two adjustments: one to your terminals, and one to the printer.
Adjust Your Terminals: Modify Terminal Record
Do this with each terminal you'll be using with the Model 3321.
1. From the main menu, type MTR and press <Enter>.
2. Press the <Tab> key, then the <Enter> key, so that the cursor lands on the Printer Type field.
Type S, then press <Change>.
3. Press <End> to return to the main menu.
Adjust Your Printer: Change to 17 characters per inch
The printer must have paper loaded before you can make this adjustment.
1. Make sure the printer is turned off. Check the switch located on the right side of the printer,
toward the back.
2. Hold down the MODE button located on the front panel of the printer and turn the printer on.
The word Menu lights up on the front panel.
3. Press the ITEM button two times. The following lines print:
Font
Font
4. Press the SET button two times. The following lines print:
Font
Font
5. Press the MODE button to enable the printer.
1075248 © 1991, 1997 Triad Systems Corporation All Rights Reserved
Print Mode
HSD
Pitch
10 CPI
Pitch
12 CPI
Pitch
17.1 CPI
Advertisement
Summary of Contents for Triad 3321
- Page 1 Important Steps that Make Your Printer Work with Your System To make your new Model 3321 Invoice Printer work with your Hardlines & Lumber system, you need to make two adjustments: one to your terminals, and one to the printer.
- Page 2 Important Buttons and Lights: Read this section to • become familiar with your printer’s buttons and lights. What the Levers Do: The Model 3321 printer has two • external levers. Read this section to find out what they do. •...
-
Page 3: Changing Paper
Open the tractor feed’s hinges. These hinges hold the paper to the printer. You’ll find hinges at the paper’s edges. Grasp the paper from beneath the printer and tug the paper down and out. 3321-2 Model 3321 Printer... - Page 4 You can use this knob to adjust where the printer begins printing. You may need to adjust the paper a few times before it is lined up correctly. Push the Sel button to turn on the Sel light. Model 3321 Printer 3321-3...
- Page 5 You will find the ribbon cartridge inside the top of the printer, beneath the plastic cover. Grasp the black ribbon cartridge by its sides and pull. It should come up with almost no effort. 3321-4 Model 3321 Printer...
-
Page 6: About Your Printer
Printing Capacity: Triad recommends that you print no more than 150 pages per day, or 3,000 pages per month with your Model 3321 printer. It’s unlikely you will ever have a need to print so many forms at once. Your Model 3321 was not meant to print on multi-part forms that are more than four parts thick. - Page 7 The Form Feed Button: When you push the Form Feed button, the printer will advance the paper by one page — about 11 inches. Since your Triad system normally takes care of feeding the printer paper, you won’t need to use this button often.
- Page 8 You may want to look at the topic “Changing Paper.” The alarm light could also mean that something is wrong with your printer. If you think this may be so, call the Triad Service Center. •...
-
Page 9: If You Have Problems
If you can’t seem to find an answer here, or in the rest of this printer section, you should call the Triad Service Center for help. The printer doesn’t print when it should. Usually, this •... - Page 10 The lever is left of the word “Hot.” Set the switch to for paper that’s one sheet thick Set the switch to for two or three sheet paper Set the switch to if you’re using four-sheet paper Model 3321 Printer 3321-9...