Table of Contents
Advertisement
Quick Links
CANFORD AUDIO PLC
CROWTHER ROAD WASHINGTON
technical data
TYNE & WEAR NE38 OBW, UK
admin (0191)418 1000
sales (0191)418 1122
fax (0191)418 1001
MINX MIXER
OPERATING INSTRUCTIONS
Manufactured by Canford Audio plc
Under licence from Audio Systems Components Ltd
02-406 (Issue 1) 02/02
MINX MIXER - OPERATING INSTRUCTIONS
02-406 (Issue 1) 01/03
Advertisement
Table of Contents
Summary of Contents for Canford MINX MIXER
-
Page 1: Technical Data
TYNE & WEAR NE38 OBW, UK admin (0191)418 1000 sales (0191)418 1122 fax (0191)418 1001 MINX MIXER OPERATING INSTRUCTIONS Manufactured by Canford Audio plc Under licence from Audio Systems Components Ltd 02-406 (Issue 1) 02/02 MINX MIXER - OPERATING INSTRUCTIONS 02-406 (Issue 1) 01/03... -
Page 2: Table Of Contents
- Output Attenuator - Battery Switch - IEC Mains Socket - Fuse Holder - Headphone sockets - Battery Compartment Phantom Power module Phantom Power (obsolete version) 12Volt powering Technical Specifications MINX MIXER - OPERATING INSTRUCTIONS 02-406 (Issue 1) 01/03 - 2 -... -
Page 3: Introduction
These are just typical uses. The Minx is so compact and versatile, yet with such good quality specs. it can be used as a sub-mixer at concerts, feed ENG cameras/VCRs or for local work. MINX MIXER - OPERATING INSTRUCTIONS 02-406 (Issue 1) 01/03... -
Page 4: Operating Instructions
(O/P) or control line input (CUE) on their respective headphones. For engineer only, monitoring will be overridden by PFL if selected. Talkback Routing (PTT) MINX MIXER - OPERATING INSTRUCTIONS 02-406 (Issue 1) 01/03 - 4 -... -
Page 5: Talkback Routing (Ptt)
The oscillator circuit employed uses a thermistor which will initially overshoot before settling back to 0dBu. If following equipment is sensitive to overshoot, turn LIMITER on before using oscillator. MINX MIXER - OPERATING INSTRUCTIONS 02-406 (Issue 1) 01/03 - 5 -... -
Page 6: Back Panel
If OFF/CHARGE position selected the mixer is mains powered and the Ni-Cads are being charged. DO NOT OPERATE THE MINX FROM MAINS POWER WITH ORDINARY DRY CELLS AND OFF/CHARGE POSITION SELECTED. MINX MIXER - OPERATING INSTRUCTIONS 02-406 (Issue 1) 01/03 - 6 -... -
Page 7: Fuse Holder
Phantom Power supply, unless Off/Charge is selected and/or Phantom Disable is selected. The drain on this battery then depends on the number and type of microphones in use. MINX MIXER - OPERATING INSTRUCTIONS 02-406 (Issue 1) 01/03 - 7 -... -
Page 8: Phantom Power (Obsolete Version)
Do not use 12 Volt ‘T’ Powering with 48 Volt Phantom power microphones or Dynamic mics. Do not use 48 Volt Phantom powering with 12 Volt ‘T’ Power microphones or Dynamic microphones. MINX MIXER - OPERATING INSTRUCTIONS 02-406 (Issue 1) 01/03 - 8 -... -
Page 9: Technical Specifications
= +ve Phase or ‘Hot’ Ring = -ve Phase or ‘Cold’ Sleeve = Ground Bare wire terminals: = +ve Phase or ‘Hot’ Black = -ve Phase or ‘Cold’ MINX MIXER - OPERATING INSTRUCTIONS 02-406 (Issue 1) 01/03 - 9 -...