HX E-33A-100701 User Manual

Hx studio monitor

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

SER

UIDE

HX E-33A-100701

Table of Contents

Need help?

Do you have a question about the E-33A-100701 and is the answer not in the manual?

Questions and answers

Summary of Contents for HX E-33A-100701

Page 1 UIDE HX E-33A-100701...
Page 2: Table Of Contents
ONTENTS Introduction ................................... 3 Warranty ..................................3 Warnings..................................3 Loudspeaker Face Information ............................4 Loudspeaker Sound Dispersion ............................. 4 Room Preparation ................................5 Loudspeaker Cabling ..............................9 Input and Control ................................. 12 Maximum Output and Listening Distance ........................13 Quick Digital Output Adjustment ..........................13 Surface Cleaning .................................
Page 3: Introduction
NTRODUCTION Thank you for your purchase of HX studio monitor E-33A-100701. HX E series loudspeakers provide high end audio reproduction, maximum transparency and low distortion output. ARRANTY Warranty covers all defects in material and workmanship. No user maintenance is necessary. All equipment has been tested with care and precision.
Page 4: Loudspeaker Face Information
OUDSPEAKER NFORMATION OUDSPEAKER OUND ISPERSION The optimum sound coverage for the device is shown in the pictures below.
Page 5: Room Preparation
REPARATION Loudspeaker and amplifier box dimensions can be seen below: Add an extra 1.5in (38.1mm) extrusion to the box depth for the amplifier heat sink.
Page 6 Please provide an appropriate size of a loudspeaker stand/base for the loudspeaker. Due to the low frequency reproduction capability, vibration isolator/pad is recommended to be placed below the each loudspeaker box (between the box and the stand). Loudspeaker can be positioned in different setup. Please see description for different position in the following page.
Page 7 Above picture shows the preferred setup. Woofers are located “inside” and loudspeaker is mounted horizontally. This box position is the default position for E-33A-100701. Above picture shows another variation of the horizontal position. Placing woofer “outside” may result in slightly narrower stereo image.
Page 8 As previously discussed, locating the tweeter near a boundary is not a good idea. We do not recommend this position. Above picture shows the preferred position if the loudspeaker needs to be mounted vertically. Tweeter should be placed “outside” and far from boundaries. If the tweeter is too high relative to the listening plane, please provide down-tilt.
Page 9: Loudspeaker Cabling
OUDSPEAKER ABLING The correct connection of the cables to loudspeaker’s terminal is shown below: Each cable is marked by dot (one, two or three) and each pair has one end that is marked by a black marker. The dot on the cable corresponds to the dot on the sticker near the terminal. The black marker at the end of the cable corresponds to the negative (black terminal) input.
Page 10 Please see the picture below, showing the dot marker and connection detail: Another closer look at the terminal cable is shown below:...
Page 11 The included cable from the amplifier to the loudspeaker is 1.5m / 6 ft long. If you want to replace or extend the extension cable, please see the information below for the color code on the amplifier cable: On the loudspeaker terminal: one dot is tweeter input terminal, two dots is 7 in midrange woofer input terminal and three dots is 10 in subwoofer input terminal.
Page 12: Input And Control
NPUT AND ONTROL The amplifier does not have user control i.e. volume control, on/off button or preset buttons. It is highly recommended to place the amplifier AC mains cable with a user controllable switch so it can be turned off if it is not used. Input for the amplifier is one XLR cable.
Page 13: Maximum Output And Listening Distance
ISTENING ISTANCE E-33A-100701 is optimized for 1-4m (3.3ft – 13ft) listening distance. It is not recommended to have a listening distance of less than 1m (3.3ft). The amplifier sensitivity is 1.4V RMS (5.1 dBu, 2V peak), therefore a 0.5V RMS pink noise with 12dB crest factor (-3.8dBu, 2V peak) can be safely passed to the loudspeaker without clipping/distortion.
Page 14: Third Party Accessories
ARTY CCESSORIES To further support the operation of E-33A-100701 loudspeaker, several third party accessories can be used such as: 1. Loudspeaker Stand Please make sure the loudspeaker stand is able to support up to 27 kg (60 lbs). The base dimension should not be too small.