Table of Contents
Advertisement
CLIPPED HEAD
FRAMING NAILER
Cloueuse de charpente à
clous à tête coupée
Clavadora para
estructuras con
cabezal recortadoa
Instruction manual
Manuel d'instructions
Manual de'instrucciones
Française: Page 17
Español: Página 34
www.portercable.com
INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.
LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
FC350B
9R195706RA
1 - ENG
Advertisement
Table of Contents
Related Manuals for Porter-Cable FC350B
Summary of Contents for Porter-Cable FC350B
- Page 1 Instruction manual Manuel d'instructions Manual de'instrucciones Française: Page 17 Español: Página 34 www.portercable.com INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. FC350B 9R195706RA 1 - ENG...
-
Page 2: Definitions - Safety Guidelines
IMpORTAnT SAFeTy InSTRUCTIOnS FOR pneUMATIC TOOlS save these instructions When using any pneumatic tool, all safety precautions, as outlined below, should be followed to avoid the risk of death or serious injury. Read and understand all instructions before operating the tool. DeFInITIOnS - SAFeTy GUIDelIneS The definitions below describe the level of severity for each signal word. - Page 3 • Do not use bottled gases to power this tool. Bottled Fig. e compressed gases such as oxygen, carbon dioxide, nitrogen, hydrogen, propane, acetylene or air are not for use with pneumatic tools. Never use combustible gases or any other reactive gas as a power source for this tool.
- Page 4 • never carry tool with finger on trigger. Using the Fig. K trigger lock-off will prevent accidental discharge. Accidental discharge could result. • Do not overreach. Maintain proper footing and balance at all times. Loss of balance may cause personal injury. (Fig.
- Page 5 could ignite gases causing a fire. Driving a nail into Fig. p another nail may also cause a spark. (Fig. R) • Keep face and body parts away from back of the tool cap when working in restricted areas. Sudden recoil can result in impact to the body, especially when nailing into hard or dense material.
-
Page 6: Nail Specifications
Important Safety Instructions. save these instructions nAIl SpeCIFICATIOnS FC350B nails 0.113"–131" (2.87–3.33 mm) diameter, papertape collated clipped head framing nails lengths 2"–3-1/2" (50–90 mm) Angle 34º Air Inlet 1/4" NPT (6.4 mm) nOTe: Use only pORTeR-CABle approved fasteners 6 - ENG... -
Page 7: Tool Parts
(contact actuation mode), the tool will drive a fastener if the contact trip is bumped while the trigger is depressed. The FC350B is equipped with a selectable trigger. This trigger allows the operator to select either single sequential action trigger mode or bump action trigger mode. In accordance with the ANSI Standard SNT-101-2002, the trigger is assembled in the single sequential action trigger mode. -
Page 8: Operation
To reduce the risk of damage to the tool, only use PORTER-CABLE pneumatic tool oil or a non-detergent SAE 20 weight oil. Oil with additives or detergent will damage tool parts. -
Page 9: Actuating Tool
Read all Safety Warnings before using tool. Fig. 2 Connect the air supply to the tool. Insert fasteners (L) into T-slot (K) on end cap of magazine (J) past the nail stop (E). nOTe: Magazine will hold two full fastener strips. Pull pusher (I) back until the nail stop (E) falls behind the fasteners. - Page 10 Contact actuation trigger - (Fig. 6) Trigger lock button The contact actuation trigger is intended for rapid fastening on flat, stationary surfaces. Fig. 6 Using the contact actuation trigger, two methods are available: place actuation and contact actuation. To operate the tool using the plACe ACTUATIOn method: Depress the contact trip against the work surface.
- Page 11 DIReCTIOnAl exHAUST DeFleCTOR (FIG. 8) Fig. 8 Adjust directional exhaust deflector (A), so the exhaust air blast will be directed away from the operator. The exhaust deflector provides sixteen detented positions for directing the exhaust blast away from the operator. Grasp the deflector and rotate it to the desired position for the current application.
-
Page 12: Cold Weather Operation
Keep tool as warm as possible prior to use. Make certain all fasteners have been removed from magazine. Put 5 to 7 drops of PORTER-CABLE pneumatic tool oil in the air inlet. Lower air pressure to 80 psi (5.5 bar) or less. -
Page 13: Maintenance
RepAIRS For assistance with your tool, visit our website at www.portercable.com for a list of service centers, or call the PORTER-CABLE Customer Care Center at 1-888-848-5175 (U.S. & Canada Only). SeRvICe ReplACeMenT pARTS Use only identical replacement parts. -
Page 14: Three-Year Limited Warranty
We cannot guarantee repairs made or attempted by others. You can also write to us for information at PORTER-CABLE, 4825 Highway 45 North, Jackson, Tennessee 38305 - Attention: Product Service. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, etc.). -
Page 15: Troubleshooting Guide
Bent collation wire. fasteners. Canister or nose screws loose Tighten screws. Canister is dirty. Clean magazine. Driver tip is worn or damaged. Install Driver Maintenance Kit. Other Contact a PORTER-CABLE Authorized Warranty Service Center TOOl SpeCIFICATIOnS FC350B Height (inch/mm) 14.76/375 Width (inch/mm) 4.72/120... - Page 16 Compressor will be sufficient for tools at all production rates. Compressor will be sufficient at slow or moderate production rates, but may have difficulty at very rapid rates. Compressor will be adequate only when tools are utilized at slow production rates (punch-out or occasional use). not Recommended Portable 5.5 HP Gas...
- Page 17 The following are PORTER-CABLE trademarks for one or more power tools and accessories: a gray and black color scheme; a F “four point star” design; and three contrasting/outlined longitudinal stripes. The following are also trademarks for one or more PORTER-CABLE and Delta products: Les éléments ci-dessous sont des marques de commerce des outils et des accessoires de PORTER-...