Table of Contents
Advertisement
Quick Links
S
U
P
S
U
P
S
U
P
2
5
0
0
W
i
n
t
e
2
5
0
0
W
i
n
t
2
5
0
0
W
i
n
t
USER' S MANUAL release 1.0
This manual must be considered an integral part of the projector.
E
R
T
R
A
C
E
E
R
T
R
A
C
E
E
R
T
R
A
C
E
l
l
i
g
e
n
t
d
i
s
e
l
l
i
g
e
n
t
d
i
s
e
l
l
i
g
e
n
t
d
i
R
2
5
0
0
R
2
5
0
0
R
2
5
0
0
c
h
a
r
g
e
f
o
c
h
a
r
g
e
f
o
s
c
h
a
r
g
e
f
o
H
T
I
H
T
I
H
T
I
l
l
o
w
s
p
o
t
l
l
o
w
s
p
o
t
l
l
o
w
s
p
o
t
Advertisement
Table of Contents
Summary of Contents for Lampo Supertracer 2500 HTI
- Page 1 USER’ S MANUAL release 1.0 This manual must be considered an integral part of the projector.
-
Page 2: Table Of Contents
BEFORE CONNECTING AND USING THE PROJECTOR, IT IS IMPORTANT TO READ CAREFULLY ALL THE INSTRUCTIONS IN THIS MANUAL. QUALIFIED PERSONNEL ONLY, IN COMPLIANCE WITH ALL THE SECURITY LAWS, CAN DO THE INSTALLATION, THE MAINTENANCE AND THE UTILISATION OF THIS PROJECTOR. BEFORE CONNECTING THE PROJECTOR, MAKE SURE THAT THE FREQUENCY AND THE VOLTAGE VALUES ARE SUITABLE AS SPECIFIED ON THE PROJECTOR. -
Page 3: General Description Of Projector
GENERAL DESCRIPTION SUPERTRACER is an intelligent followspot ideal for distance between 20 and 80mt, it has an external ballast, zoom between 7.4° and 15.6° and it is perfectly balanced. Supertracer has a colour wheel, filter correction, frost filter, focusing, dimmer and strobe, this effects is controller by TRACER console or by any DMX 512 controller. As shown in the figure, the SUPERTRACER FOLLOWSPOT 2500 HTI is made up of the following parts: 1. - Page 4 REAR PANEL As shown in the figure, the following elements ca be seen on the rear panel: 1. Rear handle 2. Serial number plate 3. DMX address area 4. Control Assignment Section 5. XLR DMX 512 in/out 6. Line and electronic fuse 7.
- Page 5 NOISE LEVEL After the projector has been powered up and the initial configuration takes place, the noise produced by the projector is primarily due to its cooling system. The noise level is much lower than the limit of 70 db A permitted by law.
-
Page 6: Start-Up Procedures
START – UP PROCEDURES POSITIONING AND INSTALLATION Follow these steps for opening the package and installing the projector in its working position: • Place the projector near the place it will be installed. • Open the package and remove the anchoring elements, accessories, and User manual. •... -
Page 7: What's Inside
LAMP INSTALLATION • Switch off projector • Loosen the cheese-headed screw hexagon built in front and on the back of the projector of the top lid and remove the lid. • Remove the lamp from the packing and carefully read the Manufacturer’s instructions. -
Page 8: Dmx Channel Assignment
DMX CHANNEL ASSIGNMENT CHANNEL FUNCTION COLOUR COLOUR CORRECTION IRIS DIMMER & SHUTTER FOCUSING SPECIAL FUNCTION DMX CHANNEL FUNCTIONS are described in the table. When you address a projector keep in mind that the BASE CHANNEL (or Starting Channel) corresponds to the first channel (the colour channel, in this case), and the other functions follow in the order described in the table. - Page 9 CHANNEL 1 = COLOURS percent values decimal values 0 > 5.9 % WHITE 0 > 15 6.3 > 9.4 % WHITE / RED 16 > 24 9.8 > 13.3 % 25 > 34 13.7 > 18 % RED / YELLOW 35 >...
-
Page 10: Control Systems
CONTROL SYSTEMS TRACER CONTROL UNIT SUPERTRACER comes with a control unit mounted on the adjustable bar and connected to the projector by means of a proper cable through 9 pin din connector. The TRACER CONTROL UNIT is powered at low voltage 12 Volts directly by the projector and it is able to control the fixture in all its functions. - Page 11 DIMMER /SHUTTER SECTION This section contains the controls for light beam characteristics: INTENSITY, my means of the DIMMER, and STROBE EFFECT, using the variable speed SHUTTER. Note that the action of the slider for this section depends on the position of the Dimmer/Strobe selector. When the Dimmer LED is on, the slider adjusts the intensity of the beam.
- Page 12 CASCADE CONTROL FROM THE TRACER CONSOLE When several projectors are connected by cable, the console on the first projector can control all functions on the following projectors. For this reason, the projectors must be connected with a standard DMX cable, IN/OUT 3 or 5 pin connectors.
-
Page 13: Optical System
OPTICAL SYSTEM The SUPERTRACER FOLLOWSPOT 2500 is provided with a high-efficiency optical system made of mirror, optic condenser and two anti-flare lenses. This system lets SUPERTRACER FOLLOWSPOT 2500 project an extremely powerful and homogenous light beam. The SUPERTRACER use OSRAM HTI 2500W/SE lamp. Socket G22+cable 240000 lumen 6000K 600h Diameter at 7.4°: 0.130 for distance Diameter at 15.6°: 0.275 for distance Linear zoom from 7.4°... -
Page 14: Maintenaince
MAINTENANCE Safety guards, lenses and filters must be replaced if they are visibly damaged to the point that they become ineffective (i.e.: if they have deep slashes or cuts).. The lamp must be replaced if damaged, cracked or deformed by the heat PLANNED MAINTENANCE OPERRATION FREQUENCY... - Page 15 M3 SURFACE TEMPERATURE TEST Before you check the temperature, make sure the projector is in the full operating mode (wait about 20 minutes after switching on the projector). Use a contact probe to measure the surface temperature on the projector’s metal case and determine the hottest area at the bottom’s projector (nearest to the lamp).
-
Page 16: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Make sure the mains power is ON and the circuit breaker has No mains power supply not been triggered Projector does not turn Make sure the switch on the back of the projector is ON No power to projector Make sure the top lid is tightly closed Replace the burned-out fuse*... -
Page 17: Spare Parts
No goods can be returned, for any reason without previous authorisation from the manufactured, and the transport charges, to and from LAMPO are at the cost of the client. The warranty is not valid in the following cases: 1 If the projector was used improperly or with negligence, or if it was damaged and repaired and/or modified to the point of jeopardizing safe functioning.
Need help?
Do you have a question about the Supertracer 2500 HTI and is the answer not in the manual?
Questions and answers