1. Manuals
  2. Brands
  3. Measurement Systems Manuals
  4. Scooter
  5. MSI5200C
  6. User manual

Measurement Systems MSI5200C User Manual

Bantam portable vehicle weighing system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
MSI5200C
BANTAM
PORTABLE VEHICLE
WEIGHING SYSTEM
User
Guide
Quality
Industrial
Weighing
and Force
Measurement
Equipment
Measurement
Systems
International

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MSI5200C and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Measurement Systems MSI5200C

  • Page 1 MSI5200C BANTAM User PORTABLE VEHICLE Guide WEIGHING SYSTEM Quality Industrial Weighing and Force Measurement Equipment Measurement Systems International...

  • Page 2: Table Of Contents

    M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L TABLE OF CONTENTS Installation ................... 3 Meter ....................3 How to Set Up and Operate the System ..........

  • Page 3: Installation

    M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L THE BANTUM WHEEL WEIGHER SYSTEM Carrying Case: Used to transport and store the entire system when not in use. Weigh Pad Cable: Used to interconnect weigh pads.
  • Page 4 M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L Span Control Screw and Cap: Used only during system calibration (see Calibration Procedure). Cap should be left in place during normal operation.

  • Page 5: How To Set Up And Operate The System

    M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L HOW TO SET UP AND OPERATE THE SYSTEM Note: Typical six pad arrangement (Figure 2) allows for easy weighing of both two and three axle vehicles.

  • Page 6: External Ac Operation

    M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L The following additional procedure should be followed to gain axle as well as total vehicle weights: 8a) Drive vehicle onto front two pads.

  • Page 7: Calibration Procedure

    M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L a) Red clip to POSITIVE (+) terminal. b) Black Clip to NEGATIVE (-) terminal. Connect cable 40043-240 to the connector on the side of the meter labeled POWER.

  • Page 8: Internal Zero Adjustment

    2 through 10 if the meter does not return to 0. 12) Replace the cap screw. 13) Repeat steps 2 through 12 for each pad. Note: Measurement Systems International, Inc., will calibrate, for a fixed charge, systems that are returned to the factory. Systems must be returned freight prepaid.

  • Page 9: Battery Charging

    M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L BATTERY CHARGING Battery life is a function of several variables, including battery age, battery charge, temperature and the number of pads connected.
  • Page 10 M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L remove the plate. Unplug the battery connector and remove the battery.

  • Page 11: Troubleshooting Guide

    M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L TROUBLESHOOTING GUIDE SYMPTOM: POSSIBLE CAUSE: ACTION: Meter display is blank without Discharged Battery.
  • Page 12 M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L SYMPTOM: POSSIBLE CAUSE: ACTION: Meter reading is erratic or drifting Loose or disconnected weigh pad Check cables.

  • Page 13: Parts List

    M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L PARTS LIST Part Number Description Quantity 2 Pad 3 Pad 4 Pad 6 Pad D00376 Carrying Case, 2 Pad D00545...

  • Page 14: Figures

    M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L FIGURES ACCESS PLUG SEAL Figure 1: Access to calibration port. METER Figure 2: Six-pad system configuration.
  • Page 15 M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L 14' or 24' 14' or 24' METER Figure 3: Four-pad system configuration. METER Figure 4: Two-pad system configuration.
  • Page 16 M E A S U R E M E N T S Y S T E M S I N T E R N A T I O N A L Step 2 - Slip shrinkable tubing Step 1 - Strip 1/2 inch of on each insulated wire.

  • Page 17: The Msi Limited Warranty

    I N T E R N A T I O N A L THE MSI LIMITED WARRANTY MEASUREMENT SYSTEMS INTERNATIONAL, INC., WARRANTS load sensing elements and meters against defects in workmanship and materials for a period of one year from date of purchase and warrants electrical cables and batteries against the same defects for a period of ninety (90) days from date of purchase.
  • Page 18 MADE IN THE Measurement Systems I N T E R N A T I O N A L ©1997 by Measurement Systems International 14240 INTERURBAN AVENUE SOUTH SEATTLE, WASHINGTON 98168-4660 U.S.A. PUB.138-07-90 Printed in U.S.A. 206-433-0199 • FAX: 206-244-8470...

Table of Contents